Laney TI-BOOST Tony Iommi Treble Booster Pedal Instruction Manual
- June 9, 2024
- Laney
Table of Contents
Tony Iommi Treble Booster Pedal
TI-BOOST MANUAL
INTRODUCTION
We are very proud of our association with Tony Iommi and to have him
commission us with his only authorised signature pedal is a real honour.
The pedal functions in a similar way to Tony Iommi’s legendary modified Range
Master – giving you a significant bass cut and mid boost. We’ve included a
little more gain
and more selectable EQ options to make it more appealing to players looking to
find their own signature sounds.
FEATURES
Each of the BCC pedals have been designed to incorporate features that really matter :-
- Transparent fully buffered operation at all times.
- Super high output drive provides an excellent interface between bass guitar and effects pedals/amp.
- Much reduced cable loss.
- Consistent bass guitar volume performance at all settings.
- Signal phase integrity.
- Excellent consistent load for passive Volume pedals.
- Ultra-low noise circuitry.
- Silent switching.
- Low battery consumption.
LAYOUT
The layout of your pedal has been ergonomically designed by players, for
players, to give you control over all the features you need, quickly and
effectively.
The following pages will give you an insight into how the controls on TI-BOOST
work and interact with each other.
CONTROLS
-
DRIVE
Controls the amount of drive within the signal and will take you from clean through bluesy crunch to lead. -
LOW
Shapes the overall low frequency response of the pedal -
OUTPUT
Connect this jack to the input of your amp -
VOLUME
Controls the output level of the pedal. Allows you to hit the front end of the amp harder and generate amp distortion and sustain . Can also be used to attenuate the amplifier. -
MID
A 3 position custom voiced MID boost switch. Down position – LO mid boost, Middle – Flat, Up – Hi end boost -
HIGH
Shapes the overall Hight frequency response of the pedal. -
INPUT
Connect this jack to the output of your instrument. -
9VDC Input for external 9V external D.C. power supply
NOTES
The TI-BOOST is a true bypass pedal.
Install a good quality 9V battery into the pedal by unscrewing the base of the
pedal and fitting the battery securely to the battery connector and then
replace the base of the pedal. Do not use excessive force to tighten up the 4
base plate screws as this could damage the screws.
When not in use it is always a good idea to remove the input jack from your
pedal to prevent any unwanted battery power loss.
Caution – when you do not intend to use the pedal for a long period of time,
it is always advisable to remove the battery to prevent current loss and
battery leakage.
Alternatively – and highly recommended is the use of an external good quality
DC 9V PSU.
SPECIFICATIONS
9V PP3 battery included
External 9V DC supply – centre negative (not included)
Dimensions mm (HxWxD) 56.4 x 66 x 112
Unit weight 0.55kg
Shipping weight 0.70Kg
www.blackcountrycustoms.co.uk
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, that may cause undesired operation.
Warning: Changes or modification to the equipment not approved by Laney
can void the user’s authority to use the equipment.
Note: This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one or more
of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
**** This product conforms to the requirements of the following European
Regulations, Directives & Rules:
CE Mark (93/68/EEC), Low Voltage 2014/35/EU, EMC (2014/30/EU), RoHS
(2011/65/EU), RED (2014/30/EU), ErP 2009/125/EU
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the WEEE (Waste Electrical and Electronic Equipment) directive applicable in your country.
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Laney Electronics Ltd. declares that the radio equipment is in
compliance with Directives
2014/53/EU,
2011/65/EU,2009/125/EU
Full text of the EU declaration of conformity is available at the following
internet address:
support.laney.co.uk/approvals
NOTES….
Documents / Resources
|
Laney TI-BOOST Tony Iommi Treble Booster
Pedal
[pdf] Instruction Manual
TI-BOOST Tony Iommi Treble Booster Pedal, TI-BOOST, Tony Iommi Treble Booster
Pedal, Iommi Treble Booster Pedal, Treble Booster Pedal, Booster Pedal, Pedal
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>