SwitchBot W2701600 Blind Tilt Motorized Blinds User Manual
- June 9, 2024
- SwitchBot
Table of Contents
SwitchBot W2701600 Blind Tilt Motorized Blinds
Packllge Contants
List of Components
Preparation
You will need
- A smartphone or tablet using Bluetooth 4.2 or later.
- The latest version of our app, downloadable via the Apple App Store or Google Play Store.
- A SwitchBot account, you can register via our app or sign in to your account directly if you already have one.
Please note: If you intend to use the Cloud Service feature, you will need a SwitchBot Hub Mini (sold separately)
Safety Information
- Keep your device away from heat and humidity, and make sure it does not come into contact with fire or water.
- This product is a precision-based electronic product, please avoid physical damage.
- Do not attempt to disassemble, repair, or modify the product
- Do not use the product where wireless devices are not allowed.
Installation
Step 1: Add your Blind Tilt to the Switch Bot app Open the SwitchBot app and sign in to your account. Tap ” at the top right of the home page, find the Blind Tilt icon and select, then follow the instructions to add your device.
Step 2: Install on your blind
Use the alignment sticker to determine a rubber adapter for your blind wand
OWrap the alignment sticker around your blind wand and tuck the narrower end
of the sticker into the gap on the other end. Slide the narrower end through
the gap so the sticker tightly fits the wand. Now check which size the marks
on the sticker indicates -5, M, Lor XL
Select the rubber adapter of the right size according to the result above
Attach the rubber adapter to your blind wand
Stick the wider end of the al ignment sticker onto the headrail on the left of
the wand tilt, with the bottom edge of the rectangular area aligned with the
bottom edge of the headrail.
Pull the rest part of the alignment sticker down straight along the wand. Mark the corresponding position on the wand of where the sticker ends. This should be the top position of the rubber adapter.
Peel off the inner tape liner of the adapter and wrap it around your blind wand. Hold and pinch it for around 30 seconds. You can remove the alignment sticker now.
Attach the coupling onto the rubber adapter
DOpen the coupling and attach it onto the rubber adapter, then pinch and
fasten the spring buckle.
Twist the coupling against the wand and make sure there is no relative sliding between the coupling and the adapter.
Note: If the coupling sldes aver the adapter when you twist it, use the algrment sticker to measure your bind wand again and replace with a more suitable adapter.
Connect the Solar Panel to the main unit via the Type-C connector
OAlign the small bar on the spin buckle with the hollow circle mark on the
main unit, then plug the Solar Panel into the main unit via the Type-C
connector.
Turn the spin buckle clockwise to lock the connection point.
Check if the connection is secure. The small bar on the spin buckle should point to the solid circle mark when the spin buckle is locked.
Note: Make sure the spin buckle is securely locked to prevent dropping at a eter time.
Instal the main unit of your Blind Tilt onto the wand
O Push the slide switch on the main unit upwards to open the case.
Hold the main unit on the left of the wand. Align the gears on the coupling and inside the main unit, then close the main unit case.
Install the cord holder and anchor the Solar Panel
Hold the main unit on the left of the wand and keep it perpendicular to the
ground. Pull the cord of the Solar Panel straight up. Where the cord goes on
the headrail would be the right clip position of the cord holder
Scannen Sie den QR-Code, um die deutsche Version unseres Benutzerhandbuchs zu erhalten.
https://support.switch-bot.com./hc/de/articdes/8072316298135
Scannez le code QR pour obtenir no tre manuel dutilisation en version
française.
https://support.switch-bot.com/hc/es/articles/8072316298135
Escanee el código QR para obtener la versión en españiol de nuestro manual de
usuario.
https://support.switch-bot.com/hc/es/articles/8072316298135
Scan de QR code voor de Nederlandse versie van onze gebruikershandleiding.
https://support.switch-bot.com/hc/nl/articles/8072316298135
Scansianate il codice QR per ottenere la versione italana del nostro manuale
d’uso.
hetps://support.switch-bot.com/hc/es/articles/8072316298135
Peel off the tape liner on the cord holder’s back, stick it to the headrail, then press for about 10 seconds to secure it. You may also choose to secure the cord holder using screws
Clip the cord of the Solar Panel into the cord holder from right to left.
Stick the Solar Panel onto the window
Pass the Solar Panel through the gap between the headrail and the top slat.
Note: lat otherwise Make sure your the Soler device Panel may not passes work from propely the gap after above instalation the top
Stick the Solar Panel onto the inner side of your window with its front facing outside. Select an appropriate position near the main unit so that the cord connecting the Solar Panel will not be pulled when you open the window.
After finishing the instalation steps above, adjust the cord of the Solar Panel to make sure your Blind Tilt main unit and the wand are perpendicular to the ground, and the cord does not affect the movement of slats.
Step 3: Calibration
After you have added and installed your SwitchBot BWind Tilt, you wiW need to
calibrate it to ensure it works correctly. Please follow the instructions in
our app and make sure that the actual movement of your blind slats is the same
as the animation in our app. A recalibration is needed each time you remove
and re-install the main unit. You can choose to recalibrate your Blind Tilt
whenever you want on its Settings page
Precautions
- This product is not a toy. Keep children away from this product.
- This product is only for indoor use. Please do not use this product in humid environment or outdoors.
- Do not expose this product to liquids or operate with wet hands
- Do not place this product near heat sources in a closed environment.
- Do not attempt to disassemble, modify or repair this product, unless by an authorized technician.
- This product is designed to improve the convenience of home life. We do not account for any risks or property loss as possible results of not fol lowing this user manual.
Battery Replacement
It takes about 6.5 hours to fully charge your device battery and one full
charge could last for about 10 months. You may also hamess the sunlight to
charge using the Solar Panel provided.
- Use a 5-1A adapter to charge your device.
- Battery life is tested under conditions of opening and closing a 1.8 x 1.8m blind with a 0.6 kgf.cm wand twice a day under 25 C. Actual battery life may vary depending on different conditions.
- Using Solar Panel to charge requires a level 6 illuminance level at least.
Note: Solar charging can get you unlimited battery life of your device. Under extreme conditions, like continuous chudy days for years, the Solar Panel and the batery can last at least 3 years before next charging.
Resetting Factory Settings
Use the ejection pin to poke the Reset button once to reset your device to
factory settings. Recalibration is needed after resetting.
Firmware Upgrades
In order to improve user experience, we will regularly release firmware
updates to introduce new functions and solve any software defects that may
occur during usage. When a new fimware version is available, we will send an
upgrade notification to your account via our app. When upgrading. please make
sure your product has sufficient battery and make sure your smartphone is
within range to prevent interference.
Troubleshooting
Please visit our website or scan the QR code below for more information.
https://support.switch-bot.com/hc/en-us/categories/7566387770903
Specifications
- Model: W2701600
- Color: White
- Material: ABS, UVresistant coating
- Size: 48.8x 29.2 x 144.2 mm (1.9 x 1.1 x5.7 in.)
- Weight: 130 g (4.6 oz)
- Power: Type-C, DC 5V=1A; 2000 mAh lithium battery
- Battery Life: Apprax. 10 months or almost unlimited with the Solar Panel
- Operating Temperature: -10°C to 45″C (14 OF to 113 °F)
- Operating Humidity: 10 9% to 95 % RH
- Torque Strength: 1 kgf.cm
- Network Connectivity: Bluetooth 5.0
- System Requirements: iOS 11.0, Android OS 5.0
Warranty
We warrant to the original owner of the product that the product will be free from defects in materials and workmanship. Please note that this limited warranty does not cover:
- Products submitted beyond the original limited warranty period.
- Products on which repairs or modifying have been attempted.
- Products subjected to falls, extreme temperatures, water, or other operating conditions outside the product specifications.
- Damage due to natural disaster (including but not limited to lightning. flood, tornado, earthquake, or hurricane, etc.)
- Damage due to misuse, abuse, negligence or casualty (e.g. fire).
- Other damage that is not attributable to defects in the manufacture of product materials.
- Products purchased from unauthorized reselers.
- Consumable parts (incduding but not limited to batterles).
- Natural wear of the product.
Contact & Support
Setup and Troubleshooting: support.switch-bot.com Support Email:
support@wondertechlabs.com Feedback: 1f
you have any concerns or problems when using our products, please send
feedback via our app through the Profile > Feedback page.
CE/UKCA Warning
To comply with RF exposure requirements, a minimum separation distance of 20
cm must be maintained between the user’s body and the device, including the
antenna. Use only the supplied or an approved antenna. This device is in
compliance with the essential requirements and other relevant provisions of
directive 2014/53/EU. All essential radio test suites have been carried out
CE DOC
Hereby, Woan Technology (Shenzhen) Co., Ltd. declres that the radio equipment
type w2701600 is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address:
support.switch-bot.com
UKCA DOC
Hereby, Woan Technology (Shenzhen) Co., Ltd. declares that the radio equipment
type W2701600 is in compliance with UK Radio Equipment Regulations (SI
2017/1206). The full text of the UK declaration of conformity is available at
the following internet address: support.switch-bot.com This product can be used in EU member states and UK
Manufacturer: Woan Technology (Shenzhen) Co., Ltd. Address: Room 1101,
Qiancheng Commercial Center, No.5 Haicheng Road, Mabu Community, Xixiang
Subdistrict, Bao’an District, Shenzhen, Guangdong, P.R.China, 518100 EU
Importer Name: Amazon Services Europe Importer Address: 38 Avenue john F
Kennedy, L-1855 Luxembourg Operation frequency BLE: 2402 MHz to 2480 MHz
Operation temperature: -10 C to 45C
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and recelver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>