DISRUPTIVE TECHNOLOGIES 102634-0.3 Cloud Connector User Manual

DISRUPTIVE TECHNOLOGIES 102634-0.3 Cloud Connector User Manual

Please read this guide before 
 attempting to operate the product

Failure to follow these instructions may result in an increased risk of personal injury or damage to property, including through fire, electrical shock, burns or suffocation. Disruptive Technologies Research AS shall not be liable for damage caused where the product owner has failed to follow the instructions set out in this guide No changes shall be made to the equipment without the manufacturer’s permission as this may void the user’s authority to operate the equipment.

Warnings

• Do not use outdoors
• Use in a dry environment
• Do not plug in a damaged device
• Do not remove screws or open device
• The mounting bracket must be secured with screws if installed above 2 meters.
• The Ethernet port must only be connected to a LAN within the same mains ring
• Unplug the power supply unit from the mains if the device is not in use.

Cloud Connector EU
Frequency Band ISM 868 MHz Transmit Power < 100 mW

Celluar Version: LTE Cat-1

LTE FDD: B1/B3/B7/B8/B20/B28

Output Power: LTE Power Class 3 (23 dBm ± 2 dB)

CE: Hereby, Disruptive Technologies Research AS declares that the radio equipment model 102505 and model 102673 are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.d21s.com/doc

UK: Hereby, Disruptive Technologies Research AS, declares that the radio equipment model 102505 and model 102673 are in compliance with UK SI 2017, No 1206: Radio Equipment Regulations. The full text of the UK DoC can be found at the following web address: www.d21s.com/doc

Frequency Band ISM 915 MHz

Transmit Power < 100 mW

Celluar Version: LTE Cat-M1

LTE FDD: B2/B4/B5/B12/B13/B25/B26/B66/B85

Output Power: LTE Power Class 5 (21 dBm ± 1.5 dB)

Compliance statement: www.d21s.com/doc

FCC: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with FCC radiation exposure limits for an uncontrolled environment. This device shall be installed and operated with a minimum distance of 20 cm between users or bystanders and the device.

ISED: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license- exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference
2. This device must accept any interference, including interference that may cause undesired operation of the device This equipment is exempt from the routine RF exposure evaluation requirements of RSS-102. This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders.

Cloud Connector

Getting Started
Cloud Connectors relay data from wireless sensors into the DT cloud infrastructure.

1. Connecting to Power
   Use the provided power supply to power the 
 Cloud Connector.

2. Connecting to the Cloud
   If the device has a cellular modem it will automatically start connecting to the cloud service. If not, plug in an ethernet cable to establish a connection.

3. Observe the Status Indicator
   Pulsing White
   Connecting / updating, this can take up to a few minutes.
   Solid White
   Connected to the Internet and fully operational.
   Solid Red
   Not connected, visit d21s.com/help for troubleshooting.

Operating Conditions

Temperature: 0 to 50°C (32 to 122°F)

Humidity: 10 to 90%RH (non-condensing)

Power Supply

External DC, 5V 2A
Only use a power supply compliant to EN or IEC 62368-1:2014 
 or later with ES1 and PS2 or PS1 classification

Power Consumption
Average < 3W

Construction
IP20, Polycarbonate (PC)

Symbols

 Conformité Européenne
 (Valid for EU version)

 UK Conformity Assessed (Valid for EU version)

 Federal Communications Commission 
 (Valid for US version)

 Waste of Electrical and Electronic Equipment

 Barrel Jack Polarity
 Center Positive

 UL Certified (Valid for US version)

Wall Installation

1. Secure the mounting bracket 
 to the wall with screws. If mounted below 2 meters, 
 the adhesive can be used alone.

2. The Cloud Connector attaches to the bracket with a friction bayonet mount.

3. Align the slots and mount the Cloud Connector onto thebracket.

4. Turn the Cloud Connector 45° degrees to secure it in place.  Connect the power cable (and ethernet cable for ethernet version).

Drop Ceiling Installation

1. Remove the tile from the ceiling to perform the installation. The mounting bracket is attached to the tile using the provided backing plate with two screws and nuts. The Cloud Connector attaches to the bracket with 
 a friction bayonet mount.
   

2. Drill a 15 mm hole, 6 cm from edge of the device for cables.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>