STRONG SRT 24HC4023 HD TV User Manual

STRONG SRT 24HC4023 HD TV

Safety Instructions

Only use attachments/accessories specified or provided by the manufacturer (such as the exclusive supply adapter, battery etc.

• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
• The ventilation should not be impeded by covering the ventilation openings with items, such as newspaper, table cloths, curtains, etc.
• The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
• The mark indicates a risk of electric shock.
• The external wires must be installed by an instructed person or ready made leads or cords must be used.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
• Danger of explosion if the battery is incorrectly replaced.
• Replace only with the same or equivalent types.
• The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.
• Excessive sound pressure from HEADPHONESs and headphones can cause hearing loss.
• Listening to music at high volume levels and for extended durations can damage one’s hearing.
• In order to reduce the risk of damage to hearing, one should lower the volume to a safe, comfortable level, and reduce the amount of time listening at high levels.
• The mains plug or appliance coupler is used as disconnect device, it shall remain readily operable.
• When not in use and during movement, please take care of the power cord set, e.g. tie up the power cord set with cable tie or something like that.
• It shall be free from sharp edges or similar which can cause abrasion of the power cord set.
• When put into use again, please make sure the power cord is not damaged.
• In case of damages, please get the power cord replaced by a similar one with the same specifications.
• The absence of a light indication on the apparatus does not mean that it is fully disconnected from the mains.
• To disconnect the apparatus completely, the mains plug must be pulled out.
• Attention should be drawn to environmental aspects of battery disposal.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• To prevent the spread of fire, keep candles or other open flames away from this product at all times.
• USB terminal can provide a maximum of 500 mA.
• Equipment with this symbol is a Class II or double insulated electrical appliance.
• It has been designed in such a way that it does not require a safety connection to electrical earth.

Operating Environment

• Do not install this equipment in a confined space such as a bookcase or similar unit.
• Do not use the set near damp, and cold areas, protect the set from overheating.
• Keep away from direct sunlight.
• Do not use the set near dust place.
• Do not attach candle to accessible opening area, to avoid flammable foreign material from entering the TV

WEEE Directive
Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Storage

Your device has been carefully checked and packed before shipping. When unpacking it, make sure that all the parts are included and keep the packaging away from children. We recommend that you keep the carton during the warranty period, to keep your device perfectly protected in the event of repair or warranty.

Accessories

• 1x installation instructions
• 1x safety instructions/warranty cards
• 1x remote control
• 2x AAA batteries
• 1 x 12 volts cable supply vehicle.

Equipmet set up

Install the display on a solid horizontal surface such as a table or desk. For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. This apparatus can be used in tropical and/or moderate climates.

Stand assembly instruction

1. Carefully place the TV with its front side facing down on a cushioned flat surface in order to protect the TV and the TV screen from damage.
2. Take out the 2x feet and assemble them to the TV.
3. Fasten the feet to the bottom of the TV using the 4 x ST3 x 12mm screws.

WARNING
Indicates warning information.

NOTE
Indicates any other additional important or helpful information.

MENU
Represents a button on the remote control or the TV Bold characters.

Move to
Represents a menu item within a window Italic characters.

INSTALLATION Default PIN code: 0000

Front panel/underside

NOTE
The graphics are for representation only.

1.  Power indicator /remote sensor
2. Speakers
3. Buttons: V-/V+, CH-/CH+.
4. Combo button; Input source, Menu, Standby/ON

Rear panel

NOTE
The graphics are for representation only

AC INPUT (FIXED CABLE)

Main power cable (180 – 240 V ~ 50/60 Hz)

Vesa 100 x 100

4 x screws holes to mount TV to wall.

NOTE
The graphics are for representation only.

• Volume up/down button
• Menu Press to turn the TV on or standby/Enter Menu
• Channel up/down button

Side panel

NOTE
The graphics are for representation only.

DC IN 12V input (11.25V ~ 13.75V), normally intended for boats and caravans. Alternative to the 220V power supply. USB Connect a USB device for playback of multimedia files.

COMMONINTERFACE (CI)

Connect a Conditional Access Module (CAM).

HEADPHONES

Speakers will be muted when HEADPHONES is plugged in and headphone selected.

AV IN

3.5 mm female jack entry for composite video and left/right audio connection.

HDMI Connect

HDMI input signal from a signal source such as DVD, Blu-ray player or game console.

S/PDIF (coaxial)

Use an RCA cable to connect your TV to a compatible digital amplifier or Home theatre set.

SATELLITE

IN Connect a satellite dish to the TV for searching programmes.

ANTENNA IN

Connect a terrestrial antenna or cable connection from your provider to the TV for searching programmes.

NOTE
The 12V DC input port of this TV set, is only intended for stable DC voltage. The input voltage range is 11.25V ~ 13.75V. User cannot use power input beyond the voltage range, otherwise it may damage the TV set. In no case both 12V connector and 230V power shall be connected to the TV at the same time. It could damage it.

Remote control

1. Press to turn the TV on or standby.
2. Press to mute or restore the volume.
3. 0 ~ 9 Choose channel directly.
4. ECO Screen brightness modes for energy saving
5. EPG Press to display the current EPG information in DTV mode.
6. VOL +/- Adjust the volume up or down.
7. Change the maximum input programmed digit
8. CH +/- Change programmed up or down. Big steps in Channel list.
9. INFO Display information about the current source.
10. SOURCE Select the input source mode. SAT/ DVBT/HDMI…
11. RETURN Press to go back to previous viewed channel.
12. MENU Open the menu options. Step back in some menu options.
13. Exit the current menu or page.
14. Navigate the menu or select channel list group
15. OK Confirm the selection or to call channel list.
16. TEXT Press to enter or exit the Teletext menu.
17. SUB Enable/disable subtitles in DTV/USB mode.
18. LIST Press this button to call one or return to channel list
19. Use / button select one.
20. FAV Press to view your assigned favorite list.
21. 1. COLOUR BUTTONS Press to execute the prompt function in TV or DTV menu mode.
22. AUDIO Press to select available audio languages. Selecting audio description, a narrator will describe what is happening on the screen for blind or visually impaired viewers. Press again to turn it off depending on broadcast.

Installing the batteries

Place 2x AAA batteries in the battery compartment of the remote control. Make sure to match the polarity markings inside the compartment.

NOTE
Pictures are only for reference. Actual items may differ.

• Slide the cover horizontally.
• Put 2x AAA batteries in the compartment and make sure the polarity is correct.
• Slide horizontally to close the cover.

Precautions for using the battery

Improper using of the battery will cause leakage. Carefully follow these instructions.

• Please note the batteries’ polarity to avoid short circuit.
• When the battery’s voltage is insufficient which affect the use range, you should replace it with a new battery.
• Remove the batteries from the remote control unit if you do not intend to use it for a long time.
• Do not use different types of batteries (for example Manganese and Alkaline batteries) together.
• Do not put the battery into fire, and charge or decompose the battery.
• Please dispose batteries abide by relevant environmental protection regulation.

Using the remote control

• Use the remote control by pointing it towards the remote sensor.
• Items between the remote control and the remote sensor could block normal operation.
• Do not cause the remote control to vibrate violently.
• Also, do not splash liquid on the remote control, also do not put the remote control in a high humidity place.
• Do not place the remote control under direct sunlight which will cause deformation of the unit by heat.
• When the remote sensor is under direct sunlight or strong lighting, the remote control will not work.
• If so, please change the lighting or TV’s position, or operate the remote control closer to the remote sensor.

FIRST TIME INSTALLATION

After all connections have been made properly, switch on your TV. Insert the main power plug into the wall outlet, now the red LED light should light up. Press the q button on your remote control to wake the TV up. The language and country selection will appear on the screen. Use t u to select the OSD Language of your preference. Use pq to select the Country and use t u again to select the region you are using this TV. This country/region selection is an important setting, it will set the time zone and will try to sort region channels at first or in a specific order. If all settings are made, confirm with OK on your remote control and follow the next steps. On the next screen, you can select which tuner you like to use and which channels you’d like to search for. Choose Tuner Type and by pressing t u you can choose between DTV, ATV or DTV + ATV (DTV to
search digital broadcasts; ATV to search analogue broadcasts). After you made your selection, press q to proceed to Digital type. In this menu you can select which input source you would like to use

• DVB-S to receive satellite broadcasts if you are equipped with a satellite dish.
• DVB-T to receive terrestrial broadcasts by using indoor or outdoor antenna.
• DVB-C to receive cable broadcasts.
• Connection to cable outlet box
• Then the next screen appears depending from the tuner selection you choose.

DVB-S/S2 installation

Satellite Setting

Press rght or left to select the satellite your dish is aimed at. Use the t u pq buttons to change settings for your satellite installation for each specific satellite.

Channel Search

Press up , down , right and left to highlight the options of choice and press OK to start the channel search.

Scan Mode

Choose between Default (recommended), Blind Scan and Network and Fast

Scan

Channel Type Select Free to search Free-To-Air channels only, Select Scramble to search Encrypted channels only, All Channels to search FTA and Encrypted channels.

Service Type

Select DTV to search Digital TV channels only, RADIO to search radio channels only or All for a complete search. It is recommended to use the default settings.

NOTE
Fast Scan option allows you to load pre-installed channel list from some providers. This selection list appears when you have chosen Fast Scan and confirm with OK button.

DVB-T/T2 installation

Terrestrial Setting

Here you only need to press OK to start searching. All settings are automatically set by country selection you made in first step.

NOTE
If you have an active antenna, please check the user manual of the antenna for external power supply. The TV can NOT supply power used for an active antenna.

DVB-C installation

Cable Setting

Press up, down ,right and left to highlight your settings.

Scan type

You can select Network Scan, Full, or Blind Scan. Default Network Scan for quick search advised.

NOTE
Full scan will have a duration of approximately 20 minutes, depending on your cable network.

Network ID

Please enter (with 0 ~ 9) the used Network ID from your provider.

Frequency

Please enter (with 0 ~ 9) the main frequency used by your provider in KHz.

Symbol

Please enter (with 0 ~ 9) the used Symbol from your provider Ks/s.

NOTE
Please check the settings for your cable system used by your provider. Press OK to continue and to start search process. We hope you will enjoy it for many years.

ELECTRONIC PROGRAMME GUIDE (EPG)

EPG stands for Digital Electronic Programme Guide. It is supplied by the programme providers and offers information on broadcasted programmes. You can access it in digital mode by pressing EPG on the remote control. Press EPG to bring up the EPG interface. Use to select a programme. Use to select an event from one channel. Press INFO to see more details from selected event. If you like this event and want to set a reminder. Just press GREEN button and reminder is set. You can set even Timer for this event 1 x time/Daily/Weekly/Always just be repeating this button. This Timer overview is in menu to find under name Schedule List.

Then press the COLOUR BUTTONS for entering the required settings.

• GREEN Set reminder or timer for event.
• YELLOW Previous day EPG overview.
• BLUE Next day EPG overview.

MENU SETTINGS

Below items depend if they are available of select input source. Use SOURCE button to select other input source. The selections under this button are, Satellite, DTV, ATV, AV, HDMI 1, HDMI 2 and Media.

Menu control DTV mode

Press MENU to enter the main menu. Press t u to select an item. Press  left and right and OK to select the submenus. Press MENU to exit the item.

Picture menu

Picture Mode
Select the automatic picture control mode. Available choices are Dynamic, Standard, Mild and Personal.

Colour Temperature
Select the overall colour tone of the picture. Available choices are Cool, Normal and Warm.

Noise Reduction
Eliminates noise in the picture. Available choices are Off, Low, Middle, High and Default.

Aspect Ratio
Select the aspect ratio (display proportions) according to your video signal type or preference. Available choices are Auto, 4:3,16:9, Zoom1, Zoom2 and Point To Point. Note: Some options may not be available under some sources.

HDMI mode
Select one of the option. Auto, Video, or Graphic. In the Personal mode, settings can be changed for Brightness, Contrast, Colour and Sharpness.

Contrast/Brightness/Colour Tint/Sharpness

If Picture Mode is set to Personal you are able to change the following settings. Press up and down to select an option, then press left and down to adjust.

Contrast

Adjust the highlight intensity of the picture, but the shadow of the picture is invariable.

Brightness

Adjust the optical fiber output of the entire picture, it will effect the dark region of the picture.

Colour

Adjust the saturation of the colour based on your own preference.

Tint No function

Sharpness Adjust the peaking in the detail of the picture.

Colour Temperature

In this menu you can change the overall colour cast of the picture. Press up and down  to select Colour Temperature, then press OK to enter a sub-menu. Press pq to select the
relevant picture effect (DEFAULT: Cold Normal Warm.

Cold

lncrease the blue tone for the white.

Normal

Increase the neutral colours for the white.

Warm

lncrease the red colour for the white.

Noise Reduction

In this menu you can filter out and reduce the image noise and improve picture quality. Press up and down  to select Noise Reduction, then press OK to enter a sub-menu.
Off Select to turn off video noise detection.

Low

Detect and reduce low video noise.

Middle

Detect and reduce moderate video noise.

High

Detect and reduce enhanced video noise.

Default

Set as Default.

Sound menu

Sound Mode Select your favourite sound mode for each input. Choices are Standard, Music, Movie, Sports and Personal. Enjoy Music Turns off the screen or switch to music source when it will be found on HDMI input.

Auto Volume

Adjust the volume corresponding to the input audio level. Options are On and Off.

S/PDIF

Type If you have connected S/PDIF output to digital home audio system. You can select “Auto” to output Dolby audio* automatically. If channel have this audio channel. Selection PCM is only stereo audio and Off is to switch off this output.

AD Switch

Turn on the Audio description, you can activate the setting of AD volume. When turn on the audio description, a narrator will describe what is happening on the screen for blind or visually impaired viewers. Only if available in DTV mode.

Installation

Press MENU to display the main menu. Press pq to select Auto Tuning in the main menu. Press OK it access and press  up and down to select the option you wish to adjust in the Auto Tuning menu. Press OK to enter and to adjust. Below items depend if they are available of select input source. Use SOURCE to select other source.

Auto Tuning

Press up and down to select Auto Tuning, select the Region Tune Type and proceed with OK. If you use DTV as input source, you can switch between DVB-T Terrestrial and DVB-C Cable. If you use Satellite as input source, you can select the satellite your dish are pointing to and how want to search for.

Dish Setup (Satellite)

The Dish Setup menu allow you to set you satellite and belonging settings as DiSC ports and LNB type. Also you can select motor DiSEqC1.2 and 1.3 function. Afterwards you may start the Auto Tuning or Manual Tuning by selecting with EPG button the wanted transponder.

DTV Manual Tuning in DVB T mode only

Search and store programmes manually. Press pq to select DTV Manual Tuning. Then press OK to enter the sub-menu. Press  right and left key to select a Channel No and then press OK to start the search. The search stops when a programme is found and this programme will be stored in the current channel position. If you want to stop the search, press MENU.

ATV Manual Tuning

First select the source type of ATV. Then in the Installation menu, select ATV Manual Tuning and press OK to access. Highlight and press pq to select Current CH 1 (maybe other number, Sound System and Channel No. Then select Search and press OK to start the search. Press u for the unit to search towards higher frequency. Press t for the unit to search towards lower frequency. The search stops when a programme is found and this programme will be stored in the current channel position. If you want to
stop the search, press MENU.

Current CH

Set the channel number

Colour System

Select the colour system (Available: AUTO, PAL, SECAM)

Sound System

Select the Sound system

Fine Tune

Adjust the frequency of the channel

Search

Start the channel search.

Channel extra settings

Programme Edit

Edit the programmes. You can press the COLOUR BUTTONS on the remote control to skip programmes, rename and delete programmes or move programmes, and add programmes to the favourite list by pressing FAV.

NOTE
Some regions are using automatically channel sorting and numbering (LCN). Which make renumbering of channels by sorting and deleting of channel list not possible. This will auto selected by country selection.

Schedule List

Press up and down  in the Channel. Select Schedule List, then press OK to enter the submenu. Use the COLOUR BUTTONS to modify your settings.

Signal Information

Showing the information of current DTV channel. Only available with DTV signal.

Cl information

Enables the user to watch and change settings of CAM modules and check values from inserted smart card.

Time menu

Press MENU to display the main menu. Press pq to select TIME in the main menu. Press OK to do further adjustments. Press OK to return to the previous menu.

Clock

The time is automatically obtained from the channel transmission and doesn’t have to be set manually. Should this function not be provided by the broadcaster, it is possible to set it by pressing OK and set date and time by pressing up down left and right.
Time Zone Press p q to select Time Zone and confirm with OK.

On Timer

This function allows to set a timer to turn ON the TV automatically. First you need to set the repetitiveness of the timer. You can choose between : Once, Every Day, Mon-Fri, Mon-Sat, Sat-Sun, Sun, OFF (default). Then set hour, minutes, source, channel and volume.

Off Timer

This function allows to turn OFF the TV. It is also necessary to set the repetitiveness and the time hour/minutes. You can choose between : Once, Every Day, Mon-Fri, Mon-Sat, Sat-Sun, Sun, OFF default.

Sleep Timer

Press up and down to select Sleep Timer. Available Options: Off, 10 min., 20 min., 30min., 60 min., 90min., 120 min.,180 min. and 240 min..

Auto Standby

This function allows you to set the automatic shutdown of your TV. Choose between 3H, 4H, 5H or Off to disable this function.

OSD Timer

This function allows you to choose how long the info banner is displayed. Choose between 5s, 15s or 30s.

Setup Menu

Language

Select the Menu OSD language of your choice. The default setting is English. Press up and down   to select the menu language and confirm with OK.

TT Language

Select the TT language of your choice of character set of TeleText.

Audio Languages

Press pq to select your chosen Audio Language, then press OK.

Subtitle Language

Press pq to select your chosen Subtitle Language, then press OK.

Hearing Impaired

Select this option to switch audio track Hearing Impaired to on. Options are On and Off.

Subtitle

Select on or off Also you can format to FTA 32 your device. Please, be a wear that all your data will be deleted.

Blue Screen

Select this option to switch on a blue screen if there is no signal on the input. Options are On and Off.

Soundbar

Select on or off

Software Update (USB)

Press OK and use t u to select Yes if you want to update the software or No to go back to the main menu. For more information see also chapter 6.2.4.

HDMI

Auto Switch With this option you can set CEC function ON/OFF. With the CEC function your other devices if they support CEC function that are connected to the
HDMI1 port can be operated with one remote control.

SW information

SW information of TV appears in this menu.

Lock

Press MENU to display the main menu. Press pq to select the Lock menu settings. Press OK to do further adjustments. Press p q to select the options. The following options are available

• System Lock This option allows you to enable or disable the password protection.
• Press OK to set this function On or Off.
• Set Password The default password is 0000, to customize the password press OK and follow the instruction within the menu.
• Channel Lock This option allows you to prevent viewing of one or more channels.
• Press OK to display the channel list and select with the channel you want to be locked.
• Press GREEN to lock it.
• Consider the same procedure to lock other channels if needed.
• Parental Guidance Press OK to enter and set the age for suitable programmes for children, then press pq.
• Key Lock This option disables the TV buttons.

MEDIA ON USB

Reminder when using the USB player

1. Some USB storage devices may not be compatible to operate smoothly with this TV.
2. Back up all of the data in the USB storage device in case data is lost due to an unexpected accident. STRONG does not assume any liability for the losses by misuse or malfunction. Data backup is consumer‘s responsibility.
3. For large file sizes, the loading speed may be slightly longer.
4. The recognition speed of a USB storage device may depend on each device.
5. When connecting or disconnecting the USB storage device, make sure the TV is not in USB mode otherwise the USB storage device or the files stored in it may be damaged.
6. Please use only a USB storage device which is formatted in FAT16, FAT32, NTFS playback only file system provided with the Windows operating system. In case of a storage device formatted as a different utility programme which is not supported by Windows, it may not be recognized.
7. When using a USB Hard Disk Drive which is not powered independently, ensure its power does not exceed 500 mA. Otherwise the TV system will change into standby mode and you must pull out the USB Hard Disk and restart the TV system.
8. An “Unsupported File” message will be displayed if the file format is unsupported or the file is corrupted.
9. FHD big picture needs longer time to process, which is not caused by the TV. Please be patient.
10. This TV may not support some multimedia files changed and upgraded as the change of the encoding format or other technical aspects advances.
11. Please refer to chapter 9. Appendix for a list of supported file formats for USB playback.

USB menu

Press SOURCE and select USB. You can view movie, music and photo files from your USB storage devices. Connect a USB storage device to the USB input terminal and select the types of media on the home page: Movie, Music and Photo. Press OK, the screen will show the connected USB device, press OK again to view the file folders and files. Press up and down  to select a folder, press OK to open the folder and select the files. Highlight the one you want to play or watch or press directly u 2 to start playing
directly. Press 3 to stop playing and return to upper lever folder. Continuously press RETURN to go back to upper level folder. Repeat again to select and play another media type.

NOTE
By choosing one of the three media types, for example Movie, the folders inside will display only video files and no other formats.

Play movies

During playback, press INFO or OK to display/exit the menu bar.Press t u on the remote control to do relevant operations and start function with OK. Play &

Pause/Stop/Prev./Next

Press u 2 to play or pause the playback. Press 3 to stop playing. Press 7 8 to play the previous or the next video file. Press INFO and use to highlight the corresponding icon on the control bar, then press OK. The TV will response accordingly.

Fast Reverse/Fast Forward

Press and hold 5 6 for seconds to draw the playing progress as your desire, then press u 2 to start the playing from the new position. Information Highlight the corresponding icon and press OK to view the information of the playing video.

Capture

Highlight the button and press OK to capture a screen shot to USB device.

Play music

• Press INFO or OK to display/exit from the menu bar.
• Press t u on the remote control to do relevant operations and start function with OK.
• Play & Pause/Stop/Previous/Next
• Press u 2 to play or pause the playback.
• Press 3 to stop playing.
• Press 7 8 to play the previous or the next music file.
• Press t u to highlight the corresponding icon on the control bar, and then press OK. The TV will response accordingly.
• Fast Forward/Fast Reverse Press and hold 5 6 for seconds to draw the playing progress as you wish, then press  2 on the remote control to start playing from the new position.
• Repeat Highlight the icon and press OK. You can select 3 different modes.
• None to disable the function, 1 to repeat one track only and All to repeat the entire list once it is finished.
• Information Highlight the icon and press OK to check the information of the playing music..

NOTE

• If one or more file(s) of the play list is selected, the buttons 7 8 will play only selected files.
• This menu only shows supported files.
• Files with other file extensions are not displayed, even if they are saved on the same USB storage device.
• An over-modulated mp3 file may cause some sound distortion during playback.
• This TV supports lyrics display in English.
• The maximum number of characters per line is 48.
• The file name of music and lyrics must be the same in order to display lyrics while the music is playing.
• If you want to show the associated lyrics on the screen with the music, you must store these in the same folder using the same file name with Irc file extensions.

Browse photos

Press during viewing INFO or OK to display/exit from the menu bar.

Play & Pause/Stop/Previous/Next

Press 2 to play or pause the playback. Press 3 to stop playing. Press 7 8 to show the previous or the next picture. Press t u to highlight the icon on the control bar, and then press OK. The TV will response accordingly.

Rotate

Highlight the icon in the menu bar and press OK to rotate the picture 90 degrees clockwise or counter clockwise.

Info

Highlight the button and press OK to check the information of the shown photo.

Zoom In/Zoom Out

Highlight the icon on the menu bar and press OK to zoom in or zoom out of the image.

Move View

When the image is magnified, use this function for convenient check. Highlight this icon, press OK, then press t upq to move the image.

NOTE
The move function is only available when the image is enlarged.

Software update via USB

From time to time you can check if there is an improved software version available. This can be viewed and downloaded from our website www.strong.tv. Search the model number on our website’s service support section. If there is an improved software version you can download the file and copy it to the root of a USB device. Then press pq button to select Software Update (USB) from the SETUP menu on your TV. Afterwards plug your USB device into the USB slot and press OK to update the respective
software. Confirm with Yes using t u. When the update is completed, remove the USB stick, disconnect your device from the main power supply and plug in again.

TROUBLESHOOTING

There maybe various reasons for abnormal operation of your TV set. Check your TV set according to the general procedures shown below. Additionally, we strongly recommend reading the detailed troubleshooting of your TV set in the full user manual available on our website www.strong.tv If your TV set does not work properly after checking the general and detailed troubleshooting, please contact your dealer, the local Service Hotline, or send an email to our support via www.strong.tv. DO NOT try to open or disassemble your TV set. It may cause a dangerous situation and the warranty will be void.

1. Check whether the power connector is completely plugged at the TV and into power socket.
2. Make sure that the switch on multipoint connectors is switched ON as well.
3. The electrical outlet may be damaged.
4. STBY LED is defective.

No Signal| The TV is not connected to a signal source (DVB-C, DVB-S/S2 or DVB-T/T2) or the antenna (terrestrial or satellite antenna) is maybe not aligned correctly respectively the according connection and distribution equipment might show malfunction, incompatibility or defectives.

DVB-T/T2: Active antennas need antenna power switched ON or external power connected.

Antenna is maybe out of digital signal reception in your area. Check reference from service providers about coverage.

DVB-S/S2: Incorrect values of some tuner parameters (e.g. one or some channel(s) changed to another transponder or are no longer emitted).

Incorrect values of LNB parameters.

The picture and sound remain frozen, or macro blocks or similar distortion are visible on the screen.| DVB-S/S2,DVB-T/T2

The reception signal is too weak or disturbed by electromagnetic, high- frequency, or other interference signals. DVB-T/T2 : Disturbances caused by signal reflections.

DVB-C, DVB-S/S2: The connection cables at the signal source are too long (too high attenuation).

DVB-T/T2, DVB-S/S2: The antenna is not properly adjusted or got misaligned after storm etc.

Any other reception or signal related problems| Generally cables might have loosened. Moisture might have entered into cables or connectors.There is heavy rain or heavy storm at present (DVB-S/S2 and -T/T2). Check the cable

connections. DVB-S/S2 and -T/T2: Check all equipment connected between the reception point and the TV.

Wait until heavy rain/thunderstorm passed. If no solution ask a local satellite specialist for advice.

DVB-S/S2: The satellite dish is NOT aligned to the correct satellite(s). Ask a local satellite specialist for advice.

DVB-S/S2: Satellite dish is too small. Trees or buildings are in path. Ask a local satellite specialist for advice.

DVB-S/S2: Signal is too strong, maybe need to be attenuated. Ask

a local satellite specialist for advice.

cables are used.

Adjust the saturation.

Switch TV on another channel. It is possible that the current programme is broadcast in black and white.

No picture, normal sound| Adjust the brightness and contrast

Radio channel is tuned to or the programme is not transmitting Video signals or another broadcasing interference/failure.

Normal picture, no sound| Press the volume up button to increase the volume level.

Audio is muted, press ! to restore the sound.

If external devices are used to loop the sound through, make sure to select correct sources and correct sound mode, for details also check advices in User Manuals from connected devices

Maybe a channel w/o audio is tuned to demo or the programme is not transmitting audio signals or there is some other transmission interference/failure.

Playback of video is causing picture freeze/ macro blocks or similar distortion, especially on HD content.| Read/write speed of your USB device could be too low. Make sure to use a USB storage device with sufficient speed and space. Pen drives USB sticks may not support sufficient speed.
The remote control does not work| hange the batteries. If you’re using rechargable ones take care to use such with low self-discharge

The batteries are not installed correctly or the types have been mixed

IR Sensor is blocked or maybe interfered from bright light

The TV switches off after a certain time| Switch ON the TV and check settings for automatic STBY function, by default the TV switches OFF after 4 hours to fulfil European low power regulations and help you to save energy.

SPECIFICATIONS

Audio

Audio Output:         2 x 3W

Video

• Channel coverage:DVB-T2: 174 MHz-230 MHz; 470 MHz-860 MHz DVB-C: 50-858 MHz DVB-S2: 950 MHz-2150 MHz
• System : DTV: DVB-T2, DVB-S2, DVB-C (Support H.265 L.4.1) ATV: PAL/SECAM (BG/DK/1) AV: PAL, NTSC, SECAM. 

Connectors

• 1X DC 12v cable not supplied
• 1x ANTENNA IN
• 1x SATELLITE IN
• 1x COMMONINTERFACE (CI)
• 1x HDMI
• 1x USB
• 1x S/PDIF coaxial
• 1x AV IN Jack 3.5mm
• 1x HEADPHONES Jack 3.5mm

General Data

• Operating voltage: 180 ~ 240 V AC 50/60 Hz
• Power consumption: max. 50 W, typ. 31 W
• Power consumption in standby: 0.5 W
• Operating temperature:  +5 °C ~ +35 °C
• Storage temperature:-15 °C ~ +45 °C
• Operating humidity: 20% ~ 80% RH, non-condensing
• Storage humidity:  10% ~ 90% RH, non-condensing
• Dimensions WxDxH in mm:  630 x120 x 422
• Net weight:   3.4 kg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>