IBERA IB-RA19 PakRak StayMount Rear Carrier User Manual

IBERA IB-RA19 PakRak StayMount Rear Carrier

Pakkak slayMount Rear Carrier
Seat stay-mounted rear rack. 1B-RA19

Tools Required

4 mm Allen key. 8 mm open-end wrench, scissors.

Supplied Parts

•  a Cargo tray
• b Short leg extenders x 2
• c Round head bolts x 8
• d Clamp rigs x 2
• e Adhesive pads x 4
• f Square washers x 4
• g Long leg extenders x2
• h Bungee hook hasps x 2
• I Rear right leg
• j Rear left leg
• k Light/ reflector bracket
• l Long flat head bolts, washers and nuts x 2
• m Short fat head bolt, washer and nut

ASSEMBLE CARRIER

Carrier is width, height and angle adjustable.

1. Lightly grease all bolts.
2. Attach adhesive pads on both ends of inner surface of seat stay rigs (see fig. 2).
3. Select one of the options below:
4. Attach rear legs to carrier (legs are left and right specific: logo faces outwards). Using Allen key and wrench in unison, attach each arm using a long flat head bolt, washer and nut. Do not tighten completely (see fig. 3a or 3b).
5. Determine leg height. Place carrier over rear wheel and hold legs on seat stays. If cargo tray is not more or less horizontal, remove bolts on front legs, rear legs or both to adjust carrier height and angle (see fig. 4). Carrier must have at least 2 cm clearance over wheel.
6. Attach clamp rigs and bungee hook hasps to carrier. lbera logo on each rig should face outwards. For front leg, insert round bolt in front leg bolt hole, then screw into bolt hole on clamp rig. For rear leg, insert round bolt in smallest hole of hasp (hasp angled outwards, facing upwards), then screw into bolt hole on clamp rig (see fig. 5, 6).

MOUNT CARRIER ON BIKE

1. Place clamp rigs about midpoint along seat stays, seating them on the inner face (see fig. 7). Unstick Velcro straps, adjust length (see fig. 8), wrap end of strap (with built-in Allen bolt) around seat stay and push them through holes in other side of clamp. Place square washers behind bolt heads, open side facing down (see fig. 9). Pull down on straps to tighten (see fig. 10), and re-stick Velcro all the way around seat stays (see fig. 11). With scissors, cut away any excess strap length that might interfere with bike wheel. Tighten bolts (see fig. 12).

2. Adjust rear leg position (width) if necessary to centre the carrier over wheel (see fig. 13).

3. When carrier is mounted correctly and length and angle adjustments have been made, tighten all bolts securely .

4. Reflector Bracket
   Mount light/reflector bracket under carrier rear crossbeam. Using Allen key and wrench in unison, mount bracket using short flat top bolt, washer and nut- bracket must protrude rearward. lighten well (see fig. 13, 14).

5. To finish, inspect to make certain:

   • Carrier is horizontal
   • Carrier has adequate clearance over wheel
   • Rear wheel is centred between carrier legs
   • Carrier does not touch or obstruct bike chain, freewheel or disk brake

Warning

1. Do not attach carrier to carbon fibre seat stays.

2. Carrier should be horizontal, and have at least 2 cm (0.8″) clearance
   over wheel.

3. Max. load 12 kg (26 lb).

4. Do not attach a child/baby seat to carrier.

5. Do not carry people on carrier.

6. Ensure bags or other luggage is securely attached to carrier before using.

7. Ensure all bolts and straps are tight before each use.

8. Rack should never touch or obstruct chain, freewheel or disk brake.

Limited Warranty

lbera warrants this product for normal usage against workmanship, and material defects to the original purchaser for two year from purchase date. Products purchased online are not covered by this warranty unless purchased from an authorised lbera online store. 1. User assumes all risk of personal injury, damage to or failure of the product when it is used in jumping, acrobatics or similar activities. 2. Warranty does not cover any incidental or consequential
damages, such as personal injury or other losses due to accident, neglect, misuse, abuse, modification, normal wear and tear, improper care and cleaning, . or failura to follow included instructions.
See other lbera products at www.ibera.info
Specifications· subject to change without notice. Ibara is a trademark of lbera co. Ltd. All other trademarks are property of their respective owners. Copyright lbera Co. Ltd. Made in Taiwan. Artwork: 06122.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>