pelsee P12 Pro Mirror Dash Cam User Manual

P12 Pro Mirror Dash Cam
User Manual

P12 Pro Mirror Dash Cam

Thank you for choosing our product. If you have any questions, please contact us at support@pelsee.com.
Thank you for choosing pelsee.
For more product information and FAQs, please visit www.pelsee.com.

NOTICE

1. Before using the product, please read and understand all the instructions in the user manual and keep the manual well for future reference.
2. Only use the original safety-tested accessories provided by the manufacturer.
3. Remove the protection film on the screen and lenses before using the product.
4. This product is intended to be mounted on an existing rearview mirror. It must not be placed in a location that may affect the deployment of airbags, and must not  obstruct the driver’s view.
5. Securely mount this product before driving. Make sure the lenses are clean and not blocked.
6. Don’t leave the product in a place that is exposed to direct sunlight or extremely high temperature. The operating temperature of this product ranges from -10°C(14°F)  to 60°C(140°F).
7. A formatted memory card is required to be inserted into the product before the first-time use.
8. Drive safe! Don’t operate the product when you are driving to avoid a traffic accident caused by distraction. Be sure to park the car in a safe place before operating.

IN THE BOX

KNOW YOUR MIRROR DASH CAMERA

Dash Cam

Rear Camera Kit

INSTALLATION OF YOUR DASH CAMERA

IMPORTANT:

1. Professional installation is recommended.
2. Stop the engine of your vehicle.

Step 1:
Insert a memory card (supports up to 256GB, class 10 or higher speed card) into the dash camera.

Step 2:
Mount the dash camera on your original rearview mirror with the rubber straps.

Step 3:
Connect the Type-C port of the car charger to the dash camera, then plug the other end of the car charger into the cigarette lighter receptacle in your vehicle.

Tip:
The USB port on the car charger can supply power to your mobile device when it’s connecting with the cigarette lighter receptacle.
Step 4:
Connect the AV out port of the rear camera kit to the dash camera, then stretch the cable through the vehicle to the rear part of it.
Step 5:
Mount the rear camera to the rear of your vehicle.

Step 6:
Insert the GPS module on the dash camera, then stick it in a proper location.

Step 7:
Start the engine to check if the installation is correct.

USE YOUR MIRROR DASH CAMERA

1. Power On/off
   Start the engine to automatically power on the camera; stop the engine to automatically power off the camera.
   Tip:
   After powering on, please touch {p} and go to Setting > Storage Set >Format the memory card to format the card.

2. Screen On/Off
   Press the power button once when the camera is on to screen it off, when it sleeps, press this button again or touch the screen to wake it up.

3. Recording Interface
   After powering on and card formatting, the camera will automatically start recording videos. The video length of each video is 1 minute by default and the oldest videos  will be overwritten by the latest video in a loop when there is no remaining capacity of the card.
   Touch to go to the main page.
   Touch to turn on or off the audio when recording.
   Touch to start or stop recording the video.
   Touch to switch among the view from the front camera, the view from the rear camera and the view from both cameras.
   Touch to take a photo.
   Touch to access the recorded videos and photos.
   Touch to lock the current video.
   Touch to adjust the display brightness. If you go to Setting to enable the option of Automatic Backlight, it could not be adjusted here.

* Gestures in the recording interface
Slide leftward/rightward on the right part of the touch screen to switch among the view from the front camera, the view from the rear camera and the view from both cameras.

Swipe upward/downward on the left part of the touch screen to see the lens’ full field of view of the camera.

Check and Delete Videos and Photos

Touch on the recording interface, or touch > Video playback to access the recorded videos and photos.

Touch to check the videos recorded and the photos taken by the front camera.
Touch to check the videos recorded and the photos taken by the rear camera.
Touch to check all the standard videos recorded by the selected camera; touch to check all the locked videos recorded by the selected camera.
Touch  to check all the photos taken by the selected camera.
Touch on a video to enter a full-screen mode as below.

* How to transfer the files?
Please remove the memory card from the mirror dash camera, then connect it with a computer via a card reader(not included) to make a file transfer.

Function Settings

Touch and Settings to check all the function settings.

Recording

* Watermark information:*
Show or hide the date and time on the recorded videos and photos.
Microphone:
Turn on or off the audio when recording.
Rear recording:
If you enable this option, the rear camera will record and save videos automatically after you connect it with the dash camera. If you disable it, the rear camera will not record  any video and only display the live picture.
Anti-flicker:**
Change the refresh rate between 50 HZ and 60 HZ.
* Resolution:
Change the resolution of the front camera.

Display

* Stream Media:*
Set the first view of the display. If you enable this option, the display will show the view from the rear camera by default after powering on; if you disable it, the display will  show the last view after powering on(for example, if the display shows the split-screen view before you power it off, the display will show the split-screen view after you power it on again).
Split Screen:
After this option is enabled, the display can show the views from both cameras on the same screen.
Automatic Backlight:
If you enable this option, the brightness of the display will be changed automatically.
Backlit:
You can manually adjust the brightness of the display here and on the recording interface only when you disable the option of Automatic Backlight.
Screen Sleep:
Set the time to enter sleep mode after a certain period of inactivity. You can choose from 1 MIN, 3 MIN and OFF.
Screen Protector:**
OFF means that the screen will be completely off when the dash camera enters sleep mode. LEFT means that the display will show the date and time on the left part of the  screen when the dash camera enters sleep mode. RIGHT means that the display will show the date and time on the right part of the screen when the dash camera enters sleep mode.

* Display Time:
OFF indicates that the date and time will not be displayed on the recording interface; ON indicates that the date and time will be displayed in the recording interface all the  time; Automatic indicates that the date and time will be displayed when you touch the screen, while they will be hidden automatically when there is no any operation for 5 seconds.

Detection

* Parking Recording:*
This option is off by default. After you enable this option, the camera will automatically start recording a locked video for about 20s when your car encounters a collision  during parking.
Time-lapse Recording:**
After enabling this option, every 30 minutes of videos will be compressed to 1 minute and then be saved in the memory card.
* Time Lapse:
The options include 1S, 2 S and 3 S. For example, if you select 1S, the time- lapse video of 1 minute will be replayed in 1S, and so on for the options of 2S and3S.

Tip:
An extra hardwire kit (not included) is recommended for using the functions of Parking Recording and Time-lapse Recording. Please contact us for more information.

* Collision Sensitivity:*
Set the different G-sensor sensitivity of collision detection when driving and parking. If you set it as High, the detection will be triggered when your car encounters a minor  collision; if you set it as Low, the detection will be triggered when your car encounters a severe collision. After the detection, the camera will start recording a locked video for 20s and save it to the card.
Power Supply Mode:**
Automatically recognize the current power supply source when a hardwire kit is used.

Storage

• Memory card information:
  Check the status of your card; check the total capacity, the remaining capacity and the used capacity of your card.
• Format the memory card:
  Touch this option to bring up the pop-up window to start formatting your card.

System Settings

• Touch Sound: Turn on or off the touch sound.
• Language: Change the language of the dash camera.
• Time Settings: Set the date and time of the dash camera.
• Volume: Adjust the volume of the system.
• Al Voice Control: After you turn on the option, an icon g will be displayed on the lower left corner of the dash camera and the camera can be controlled via the voice  commands. Tap the icon to display the voice commands or check them on page 16.
• Factory Data Reset:
  Touch this option to bring up the pop-up window to start restoring the dash camera to factory settings.

GPS info

Check the detailed GPS information after you install the GPS module.

System info

Check the software information and model no. of the dash camera.

Voice Control

This mirror dash camera can be controlled via some voice commands after you turn on the option of Al Voice Control in the System Settings.
Please check the voice commands below:

Check the GPS Data

Step 1:
Go to https://dvplayer.net/setup.html to download DVPlayer into your computer.
Step 2:
Install DVPlayer and run it on your computer. After running, please tap About

Product Registration to enter the registration code (the same as the Serial Number on the  back of the product) and email address.

Tip:
One registration code can be only used on one Windows computer and one Mac computer. If you register on the Windows computer and want to change to another Mac  computer, please tap About > Delete registration to delete the code on the windows computer, then enter this code on the Mac computer again.
Step 3:
Copy the videos in the dash camera into your computer via a card reader.
Step 4:
Launch DVD Player and open the video you want to play.

Step 5:
Tap Settings to set Video Playback mode, Language, Map, Speed Unit, Tracking linking and Auto Play Next.

SPECIFICATIONS

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>