pelsee P10 Pro Mirror Dash Camera User Manual

pelsee P10 Pro Mirror Dash Camera

Thank you for choosing our product. If you have any questions, please contact us at support@pelsee.com. Thank you for choosing pelsee. For more product information and FAQs, please visit www.pelsee.com.

NOTICE

1. Before using the product, please read and understand all the instructions in the user manual and keep the manual well for future reference.
2. Only use the original safety-tested accessories provided by the manufacturer.
3. Remove the protection film on the screen and lenses before using the product.
4. This product is intended to be mounted on an existing rearview mirror. It must not be placed in a location that may affect the deployment of airbags and must not obstruct the driver’s view.
5. Securely mount this product before driving. Make sure the lenses are clean and not blocked.
6. Don’t leave the product in a place that is exposed to direct sunlight or extremely high temperature. The operating temperature of this product ranges from -l0°C{14°F) to 60°C(l40°F).
7. A formatted memory card is required to be inserted into the product before the first-time use.
8. Drive safe! Don’t operate the product when you are driving to avoid a traffic accident caused by distraction. Be sure to park the car in a safe place before operating.

IN THE BOX

KNOW YOUR MIRROR DASH CAMERA

Dash Cam

• (P12 Pro)

• (P10 Pro)

Rear Camera Kit

INSTALLATION OF YOUR DASH CAMERA

IMPORTANT

1. Professional installation is recommended.
2. Stop the engine of your vehicle.

• Step 1: Insert a memory card (supports up to 256GB, class 10 or higher speed card) into the dash camera.
• Step 2: Mount the dash camera on your original rearview mirror with the rubber straps.
• Step 3: Connect the Type-C port of the car charger to the dash camera, then plug the other end of the car charger into the cigarette lighter receptacle in your vehicle.
  • Tip: The USB port on the car charger can supply power to your mobile device when it’s connecting with the cigarette lighter receptacle.
• Step 4: Connect the AV out port of the rear camera kit to the dash camera, then stretch the cable through the vehicle to the rear part of it.
• Step 5: Mount the rear camera to the rear of your vehicle.
• Step 6: Insert the GPS module on the dash camera, then stick it in a proper location.
• Step 7: Start the engine to check if the installation is correct.

USE YOUR MIRROR DASH CAMERA

Power On/off

• Start the engine to automatically power on the camera; stop the engine to automatically power off the camera.

Tip

• After powering on, please format the card according to the pop-up window or go to Sys setting> Disk formatting to format the card.

Screen On/Off

• Press the power button once when the camera is on to screen it off; when it sleeps, press this button again or touch the screen to wake it up.

Recording Interface

After powering on and card formatting, the camera will automatically start recording videos. The video length of each video is 1 minute by default and the oldest videos will be overwritten by the latest video in a loop when there is no remaining capacity of the card.

• Touch to go to the main page.
• Touch to turn on or off the audio when recording.
• Touch to take a photo.
• Touch to start or stop recording the video.
• Touch to lock/unlock the current video.
• Touch to check the voice commands.

Gestures in the recording interface

• Slide leftward/rightward on the right part of the touch screen to switch among the view from the front camera, the view from the rear camera and the view from both cameras.
• Swipe upward/downward on the left part of the touch screen to see the lens’ full field of view of the camera.
• Swipe upward/downward on the right part of the touch screen to adjust the brightness of the display.
• Wait for around 3s after powering on the current speed of your vehicle and the direction will be displayed on the right of the screen if the GPS receiver is installed.

Check and Delete Videos and Photos

• Touch on the recording interface, then tap File Explorer to access the recorded videos and photos.
• VIDEO-F contains the videos recorded by the front camera.
  • VIDEO-B contains the videos recorded by the rear camera.
  • VIDEO-LOCK contains the locked videos recorded by the front and rear cameras when there is a collision in driving or parking, and the locked videos recorded manually by tapping .
  • IMAGE contains the photos taken by the front and rear cameras.
• Tap the file name to play the video/photo.
• Tap and Yes on the pop-up window to delete the selected file.
• Tap and Yes to lock the selected video and move it to the category of VIDEO-LOCK.

How to transfer the files?

• Please remove the memory card from the mirror dash camera, then connect it with a computer via a card reader(not included) to make a file transfer.

SMART DRIVING ASSISTANCE

Important: This smart driving function in the dash camera is only for assistance, but not the basis of your driving.

• Touch and Smart drive to set the smart driving. For accurate monitoring, we recommend that you install the GPS receiver.

ADAS

ADAS(advanced driver-assistance system) can help perceive the world around the vehicle and then provide information to the driver.

CALIBRATE

set the ADAS areas for monitoring. Tap to move the red line upward and downward; tap to move the green line leftward and rightward; tap to move the yellow line upward and downward; tap Save to save the settings.

On/Off

• Enable or disable the ADAS function.

SETTING

• set detailed parameters for the ADAS function. Please set and adjust the sensitivity level according to your needs since higher sensitivity may cause more frequent warnings.

Alert Type

Front Car Collision Alarm: High, Medium, Weak, Closed. If the vehicle gets too close to the vehicle ahead, the system will warn the driver of an impending crash. High, Medium and Weak are different sensitivity levels. Closed means turning off this function.

• Pedestrian Collision Alarm: High, Medium, Weak, Closed. If the distance between your vehicle and the pedestrians is too short, the system will warn the driver of a potential collision. High, Medium and Weak are different sensitivity levels. Closed means turning off this function.
• Lane Change Alarm: High, Medium, Weak, Closed. When you are going to drive across the double solid white lines during lanes change, the system will warn the driver. High, Medium and Low are different sensitivity levels. Closed means turning off this function.
• The Vehicle Ahead Starts Alarm: High, Medium, weak, Closed. The system will warn you when the driver of the vehicle ahead begins to drive. High, Medium and Weak are different sensitivity levels. Closed means turning off this function.
• The Vehicle Distance Alarm: High, Medium, Weak, Closed. When your vehicle gets too close to the other vehicle, the system will warn the driver. High, Medium and Weak are different sensitivity levels. Closed means turning off this function.
• Alarm Tone: Open and Closed. Turn on or turn off the alarming sound when there is an alarm.

BSD (Blind Spot Detection)

• With the BSD function, the system will warn the driver of an approaching vehicle in the preset blind spot area.

CALIBRATE

• set the BSD area for monitoring. Tap to change the location of the red dot on four corners; tap to adjust the monitoring area; tap SAVE to save the setting.

Tip: Please do not set the BSD area when you are driving. Obey the traffic rules and pull over your vehicle, then set a BSD area first. After that, copy the settings of that BSD to another BSD area.

On/Off

• Enable or disable the BSD function.

SETTING

Set detailed parameters for the BSD function.

• Monitoring sensitivity: Very Low, Low, Medium, and High. If you select High, the system will warn you of an approaching object in the BSD area regardless of the speed difference. If you select Medium, the system will warn you of an approaching object in the BSD area when the speed difference between your car and the approaching object equals to or is greater than 0km/h. If you select Low or Very Low, the system will warn you when the speed difference between your car and the approaching object equals to or is greater than 10km/h or 20km/h.
• Monitoring type: Pedestrians, Motor, and Pedestrians/Non-motor/ Motor. You can select the object type for detection.
• Speed threshold: Okm/h, 10km/h, 20km/h, and 30km/h. For example, when you select 10KM/h, the system will warn you of an approaching object in the BSD area if the speed of your car is 10km/h; and so on for the other options.
• Alarm tone: Open and Closed. Turn on or turn off the audio alarm when an approaching object is detected.
• Alarm area display: Open and Closed. Display or hide the yellow box on the screen when an approaching object is detected.

SETTINGS

Camera Settings

• Tap and Camera setting to check the camera settings.

Back

• Tap to get back to the previous interface.

1. Record resolution
   • Tap to switch the resolution of the front camera and the rear camera.
2. Loop record
   • Change the recording time of each video. The recording time is set to be 1 minute by default. You can choose from 1 Minute, 2 Minutes, and 3 Minutes.
3. Light source frequency
   • Change the fresh rate between SOHz and 60 Hz.
4. Gsensor sensitivity
   • Set the different G-sensor sensitivity of collision detection when driving. You can select from Low, Medium, High and Closed as needed. If you select High, the camera will automatically start recording a locked video when the car encounters a minor collision. If you select Low, the camera will start recording a locked video when the car encounters a severe collision. A flashing yellow dot on the upper left corner will be displayed when recording a locked video. The video is locked and will not be overwritten.
5. Parking mode
   • Closed.Disable the function of parking mode.
   • Time-lapse record. After enabling this option, every 30 minutes of videos will be compressed to 1 minute and then be saved in the memory card.
   • Gsensor. See the content in the part of Gsensor sensity.
   • Note: An extra Hardwire Kit (not included) is recommended for using this function.
6. WDR
   • This option enables the camera to capture details clearly in both the poorly and strongly illuminated areas of the video.
7. Recording
   • Turn on/off the audio when recording.
8. Video watermark
   • Hide or show the date and time on the recorded video.
9. Rear mirror
   • Turn on or turn off the mirroring function of the view from the rear camera. If you enable it, the left and right of the view would be reversed.

Tip: The view of the saved video is not mirrored.

System Settings

• Tap and Sys setting to check the system settings.

1. Stream media switch
   • Set the first view of the display. If Stream Media is ON, the display will show the rear camera’s view by default when starting the engine. If it’s OFF, the display will show the image from the front camera.
2. Volume setting
   • Turn up or down the volume of the system.
3. Start up sound
   • Turn on/off the sound when powering on/off the camera.
4. Keystone
   • Turn on/off the sound when tapping the touch display.
5. Auto power off
   • Set the time duration to automatically power off the system. The options are Closed, 1 Minute and 3 Minutes.
6. Screen sleep
   • Set the time to enter sleep mode after a certain period of inactivity. You can choose from Closed, 1 Minute and 3 Minutes.
7. Speed Unit
   • Change the unit of the speed displayed on the screen.
8. Voice Control
   • Enable/disable the function of voice control. This function is enabled by default. The icon is displayed on the lower right corner of the dash camera and the camera can be controlled via the voice commands. Touch the icon to check the voice commands.
9. Language setting
   • Change the language of the system.
10. Time zone select
    • Select your time zone.
11. Satellite information
    • This option is only available when the GPS receiver is installed. After installation, you can check the detailed GPS information here.
12. Date & time setting
    • Set the date format and clock format of the dash camera.
13. Disk formatting
    • Tao to bring up the option of formatting the memory card.
14. Version information
    • Check the version of the camera. The information may be required when the technical support is needed.
15. Restore factory
    • Tap to bring up the option of restoring the camera to factory settings.

VOICE CONTROL

This mirror dash camera can be controlled via some voice commands after you turn on the option of Voice Control in the Sys setting.

Please check the voice commands below:

• Turn on screen, Turn off screen, Show front camera, Show rear camera, Show both cameras, Turn on audio, Turn off audio, Lock the video, Take photo.

CHECK THE GPS DATA

• Step 1: Go to https://dvplayer.netjsetup.html to download DVPlayer into your computer.
• Step 2: Install DVPlayer and run it on your computer. After running, please tap About> Product Registration to enter the registration code (the same as the Serial Number on the back of the product) and email address.
  • Tip: One registration code can be only used on one Windows computer and one Mac computer. If you register on the Windows computer and want to change to another Mac computer, please tap About> Delete registration to delete the code on the windows computer, then enter this code on the Mac computer again.
• Step 3: Copy the videos in the dash camera into your computer via a card reader.
• Step 4: Launch DVPlayer and open the video you want to play.
• Steps 5: Tap Settings to set Video Playback mode, Language, Map, Speed Unit, Tracking linking and Auto Play Next.

SPECIFICATIONS

• Video Resolution: 4Kand 1080P
• Video Format: TS
• Photo Format: JPG
• Memory Card Supported: Up to 256GB
• Operating Temperature: -10°C(14°F)-60°C{l40°F)
• Storing Temperature: -20°C (-4°F) to 70°C (lS8°F)
• Voltage: 12Vwith Car Charger

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>