Pioneer DJ BDR-X13UBK 3.2 Gen1/2.0 External BD/DVD/CD Writer User Manual

Pioneer DJ BDR-X13UBK 3.2 Gen1/2.0 External BD/DVD/CD Writer User Manual

Thank you for purchasing this Pioneer product. Before using the drive, please ensure that you read all warnings, cautions, notices, and other important safety information in this owner’s manual, which also contains important information including regulatory data, the software license agreement, details on product registration, service procedures, and guidelines on installation and use. Be sure to keep this manual in a  safe place.

Precautions Regarding Use

• Pioneer accepts no liability for the loss of any data and limits its responsibility for any failure of the product to perform properly as provided in the product’s One Year Limited Warranty. It is strongly recommended to regularly back up all critical data.
• Care must be taken not to infringe copyright restrictions under the laws of each country. If this device is used to record copyrighted materials, approval must be obtained from the respective copyright holders. The recording of copyrighted materials without the express approval of the respective copyright holders may result in legal penalties. YOU ARE RESPONSIBLE FOR YOUR USE OF THIS PRODUCT. Pioneer disclaims any and all responsibility for any legal damages resulting from the use of this device in the unauthorized copying of copyrighted materials.
• All names of corporations, products, and systems listed herein, even when the (™) or (®) symbols are omitted, are considered the registered trademarks of the respective owners.
• Specifications and the external appearance may be subject to change without notice.
• Images used in this Owner’s Manual may be different from actual product.

WARNING

This product’s classification has been determined under IEC 60825-1:2014, Safety of Laser Products. This Class 1 product contains a laser diode classified as Class 3B. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

CLASS 1 LASER PRODUCT

The following caution label appears on your unit:
Location: top of the built-in drive

WARNING: CLASS 3B VISIBLE AND IN VISIBLE LASER RADIATION WHEN OPEN, AVOID EXPOSURE TO THE BEAM.

CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION : THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT  WILL INCREASE EYE HAZARD.

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product Name: BD/DVD/CD WRITER
Model Number: BDR-X13UBK

Responsible Party Name: Pioneer Electronics (USA) Inc.

Address: 2050 W. 190th Street, Suite 100, Torrance, CA 90504
Phone: 800-421-1404
URL: https://www.pioneerelectronics.com/PUSA/

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Information to User

Alterations or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

WARNING
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

WARNING
THIS PRODUCT IS NOT WATER RESISTANT. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible.

CAUTION
This product satisfies FCC regulations when shielded cables (with Ferrite- cores attached) and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables (with Ferrite-cores attached) and connectors for connections.

WARNING
This product equipped with a three-wire grounding (earthed) plug – a plug that has a third (grounding) pin. This plug only fits a grounding-type power outlet, If you are unable to insert the plug into an outlet, contact a licensed electrician to replace the outlet with a properly grounded one. Do not defeat the safety purpose of the grounding plug.

Operating System

Operating Environment (Windows®)

The following operating environment details are guidelines. These do not guarantee operation.

DVD/CD disc recording and playback

• Supported OS: Windows 11, Windows 10, Windows 8.1

Blu-ray disc recording and playback

• Supported OS: Windows 11, Windows 10, Windows 8.1

The required operating environment may differ depending on the OS or applications
used.
Please consult with software or OS providers regarding any questions about the OS or applications.

Operating Environment (macOS®)

• Supported OS: OS X El Capitan® 10.11, macOS Sierra® 10.12, macOS High Sierra® 10.13, macOS Mojave® 10.14, macOS Catalina® 10.15, macOS Big Sur® 11, macOS Monterey® 12

Before Use

Checking accessories

• Owner’s manual (including warranty information and application product key)

• USB cable (USB Type-A → USB Type-B) (1 m (3 ft. 3 in.))

• Insulators for horizontal placement × 4

• Insulators for vertical placement × 8

• AC adapter (OWR8003-) (1.2 m (3 ft. 11 in.))

• Power cord (0.5 m (1 ft. 8 in.))

• Download the application software from the website at
  https://jpn.pioneer/cyberlink_soft/en.php
  The application download key (product key) is attached to back of this Owner’s\ manual.

• If any accessories are not included, please contact the dealer from which you purchased this product.

• Please download the Pioneer BD Drive Utility from the Pioneer website.
  https://pioneer.jp/device_e/product-e/ibs/device_e/dev00001r_e.html#DriveUtility

The Drive Utility lets the user configure various drive functions such as adjusting
the reading method if correct reading of a music CD is not possible, and setting the PureRead function, which minimizes the occurrence of data interpolation resulting from errors.

For details, refer to “Useful Functions”

Information on the product https://www.pioneerelectronics.com/PUSA/Computer/Computer+Drives/BDR-X13UBK

IMPORTANT SAFETY INSTRUCTIONS

When using this product, be sure to check the safety information indicated in this manual and on the label of the device and the AC adapter.

WARNING

Operating Environment

• Operating environment temperature and humidity:
  +5 °C to +35 °C (+41 °F to +95 °F); less than 80% relative humidity (ensure cooling vents not blocked)
  Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light).

• Ensure that water does not enter the device, and that it is kept dry. Do not use in locations with high humidity. Doing so may lead to fire or electric shock.

• Do not use in wet locations such as in bathrooms or shower rooms. Doing so may lead to fire or electric shock.

Installation

• To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on or anywhere near the equipment.
• Do not place near open flames, such as a fireplace, or heat sources. Doing so may lead to fire or deforming.
• Ensure that the power cord is fully inserted into the AC adapter, and that the  powerplug is fully inserted into the outlet. Failure to do so may cause heat to be  generatedor dust to adhere, leading to fire. Additionally, touching the blades of the power plug may result in electric shock.
• Do not connect the power plug to outlets where the plug is loose even when inserted fully. Doing so may cause heating, and lead to fire. Ask an electrician to replace electrical outlets.
• Do not place in unstable locations such as on a wobbly table or on an incline. The device may fall or topple, leading to injury.
• Do not place the device in locations subject to large amounts of oily smoke, moisture, or dust, such on a cook top or close to a humidifier. Doing so may lead to fire or electric shock.
• Do not leave in a location subject to extreme heat, such as in a vehicle with the windows closed or in direct sunlight. Doing so may lead to damage.
• Do not set device anywhere that it might accidentally be stepped or sat upon.
  Please take particular care with regard to children. The device may fall or break, leading to injury.

Using this function

• During operation, do not subject the device to shock or vibration, or plug in or unplug the USB cable or AC adapter power plug.
• During operation, do not move or pick up the device. The disc rotates at high speed, and picking up or moving the device may damage the disc. To move the device, first remove the disc, and turn the power off.
• Do not place any objects on this device, which may damage it or cause it to become unstable and fall over or fall off, potentially leading to injury.
• When using this device, ensure that you adhere to the displayed warnings and cautions from your PC manufacturer.

WARNING
When using the AC adapter and power cord supplied with this device, ensure that you observe the following.

• Do not place any objects on the power cord or AC adapter cord. Additionally, ensure that the cords do not become trapped under the device. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Do not cover the cord with a rug or other items.
• When there is dust or metal adhering to or close to the blades of the power plug, pull out the plug and then wipe them off with a dry cloth. Continuing to use the device may lead to fire or electric shock.
• Do not damage, modify, forcibly bend, twist, pull, or heat the power cord or AC adapter cord. Doing so may lead to damage to the cord, which can result in fire or electric shock.
• The AC adapter and power cord supplied are for use with this device only. Do not use them with other devices. Doing so may lead to fire or electric shock.
• Do not use any AC adapter or power cord other than those supplied with this device. Using other AC adapters or power cord may lead to fire.
• Keep the AC adapter and power cord out of reach of children. Accidentally wrapping the AC adapter around the neck may result in suffocation.
• Do not use with voltages other than the indicated power supply voltage (120 volts AC, 60 Hz). Doing so may lead to fire or electric shock.
• Do not connect this device to a direct current (DC) power source (such as used on a ship). Doing so may lead to fire or electric shock.
• Do not plug in or unplug the power plug with wet hands. Doing so may lead to electric shock.
• When unplugging the power cord, do not pull on the cord. Doing so may lead to damage to the cord, which can result in fire or electric shock. Ensure that you hold the plug when unplugging.
• Keep the power cord away from heat sources. Failure to do so may cause the insulation on the cord to melt, which can result in fire or electric shock.
• When moving the device, ensure that the power plug is first unplugged from the outlet, and that the USB cable is removed. Failure to do so may lead to damage to the cord, which can result in fire or electric shock.
• Do not touch the power plug if lightning occurs. Doing so may lead to electric shock.
• Keep the AC adapter and power cord out of water droplets.
• Do not remove the cover of the device and AC adapter or modify the device and adapter. The interior of the device contains high-voltage parts, and doing so may lead to fire or electric shock. Ask your dealer to carry out any internal inspections, maintenance, and repairs. This device is a precision instrument, so refer this product to an authorized dealer or service center if disassembly is required.
• Due to the specifications of the product, all displays turn off when operation is stopped, and thus the product may appear the same as when the power plug has been removed from the outlet. However, the power supply has not stopped providing power. To disconnect the product from the power supply completely, you must remove the power plug (breaker) from the outlet. Place the product close to an outlet, where the power plug (breaker) can be reached easily. Leaving the power plug plugged in for extended periods of time may lead to fire.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong  areprovided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• When connected to the AC adapter, do not cover the device or AC adapter with cloth or other sheets.
• Do not overload wall outlets and extension cords. Doing so may result in fire or electric shock.

Ensure you abide by the following precautions, as failure to do so may lead to fire or electric shock.

• Connect cables to the device only after checking that the cables have not deteriorated and are not damaged. Do not use any cables that have deteriorated or are damaged.
• Do not disassemble or modify the device. Do not allow metal, flammable objects, chemicals, water or other foreign matter to enter the device.

In the following circumstances, turn off the device power, unplug the PC, and contact your dealer or Pioneer.

• If the device smokes, or abnormalities such as strange smells or noises are observed.
• If water or foreign objects have entered the device.
• If the device has been dropped or its cover, the power cord, plug, or chassis is damaged.

The indicator symbols used for this product (including accessories) indicate the following:
AC (Alternating Current)
DC (Direct Current)

Cautions in Usage

• Moisture can form in the operating section of the product if the drive is taken from cool surroundings to a room with a warmer temperature. Let the drive stand for one to two hours in the new location before turning it ON.
• Do not use in dusty locations, or in locations with high temperature or humidity.
• Do not inspect or modify the interior of the device.
• Use a soft, dry cloth when wiping off dirt from the exterior of the device and the AC adapter. In the case of significant soiling, dilute a neutral cleaner five to six times in water and use this to moisten a soft cloth, wipe the soiling away, then dry with a dry cloth. Do not use volatile chemicals including benzene, thinners, alcohol, or aerosol sprays, as these may damage the surface. Before using chemically treated cloth intended for the care of electronics, carefully read the cautions included with the cloths.
• When you do not intend to use the device for an extended period due to travel, etc., for safety, be sure to unplug the power plug from the outlet.
• There are no guarantees regarding data if data is lost while using this device. Ensure you make regular backups of your data for recovery in the case of malfunctions.

Handling discs

• Do not touch or scratch the signal (shiny) side of the disc.

• Hold the disc either by both edges, or by the center hole and one edge.

• Do not apply stickers or labels to the disc.

• Do not use cracked or significantly warped discs. Doing so may lead to a malfunction in the device.
  

• When using old or rental discs, check that there are no cracks around the center hole. Centrifugal force from high-speed rotation may enlarge these cracks, causing the disc to break.

• Do not use discs with special shapes (heart-shaped,hexagonal, etc.) or other non-standard discs. Doing so may lead to a malfunction.

• If there is dust or fingerprints on the disc, use a soft cloth to wipe outwards from the center to the outer edge of the disc. Do not wipe using a circular motion on the disc.

• Do not use record spray or antistatic agents. Doing so may damage the disc.

To protect the disc, ensure it is kept in a disc case, and check for soiling or dust on the recording surface before use.

Features

Write speed/Read speed

| WRITE SPEED (MAX)| READ SPEED (MAX)
---|---|---
BD-ROM| –| 12X
BD-ROM DL| –| 8X
BD-R| 16X| 12X
BD-R DL| 14X| 8X
BD-R TL| 8X| 6X
BD-R QL| 6X| 6X
BD-RE| 2X| 10X
BD-RE DL| 2X| 6X
BD-RE TL| 2X| 4X
BD-R LTH| 8X| 8X
M-DISC (BD) SL| 6X| 12X
M-DISC (BD) DL| 8X| 8X
M-DISC (BD) TL| 6X| 6X
DVD-ROM| –| 16X
DVD-ROM DL| –| 12X
DVD±R| 16X| 16X
DVD±R DL| 8X| 12X
DVD-RW| 6X| 12X
DVD+RW| 8X| 12X
DVD-RAM| 5X| 5X
M-DISC (DVD)| 6X| 16X
CD-ROM| –| 40X, 48X*
CD-R| 48X| 48X
CD-RW| 24X| 40X

***** When the PureRead function is turned on, priority is given to reading accuracy,
and the maximum playback speed of CD audio and CD-ROM is set to 40x. The
PureRead function is turned on as a default setting. This function can be configured using the supported Pioneer BD Drive Utility

Note

• Playback of recorded BD/DVD/CD discs is possible in drives and players that support these formats. Please consult with the respective product manufacturer regarding compatibility.
  To perform high-speed writing, please use media that supports high-speed recording and writing. Refer to the Pioneer website for details.
  https://pioneer.jp/device_e/product-e/ibs/device_e/dev00003r_e.html

• Dual Disc playback

  • The Dual Disc format can record DVD-standard video and audio on one side, and audio that can be played by a CD player on the other.
  • When inserting a Dual Disc into a playback device or removing it from the device, the surface opposite to the playback side may be scratched. Problems may occur when playing the scratched side.
  • The audio side (non-DVD side) is not compliant with general physical CD standards, and may not play in some cases.
  • The Dual Disc DVD side can be played.
  • For more details on Dual Disc specifications and standards, please contact the distributor or vendor of the disc.

Part Names and Functions

Front

1. Forced ejection hole
   If the disc tray does not open even after pressing the eject button, the disc tray can be opened by inserting a long, narrow item such as the end of a large paper clip into this hole.
   In normal use, open the disc tray by using the eject button.
   When using the forced ejection hole, ensure that the power is turned off, and wait for at least one minute for disc rotation to stop.

2. Busy indicator (BUSY)
   Indicates the operational status as follows.
   When power off:  Off
   When power on:  On
   When reading:  Flashing
   When writing:  Flashing
   When tray opening/closing:  On

   • When the device is not accessed for a certain amount of time, operation stops.
     You can use the included BD Drive Utility to change the period until operation stops.

3. Eject button
   Opens and closes the disc tray.

   • When this device is connected to a Mac® with a disc inserted, this function cannot be used due to macOS® specifications. Please check the macOS User Guide for how to operate with a Mac.

4. Disc tray
   Press the eject button to open the disc tray, and with the label side facing up, place a disc in the tray aligned with the grooves.
   Press the eject button, or lightly push the front of the tray to close it.
   Do not forcefully pull the disc tray open.
   Precautions on playing 8 cm (3-9/64 in.) Discs
   

   • 8 cm (3-9/64 in.) disc adapters cannot be used with this unit.

   • When this unit is installed flat, 8 cm (3-9/64 in.) discs may be used by placing them in the 8 cm (3-9/64 in.) disc depression in the center of the disc tray.

   • When this unit is installed vertically, 8 cm (3-9/64 in.) discs cannot be used.
     Affixing the insulators (recommended affixing example)
     
     [When placed horizontally]
     [When placed vertically] Caution
     

   • When using this product, be sure to use the supplied insulator. If the product is not affixed, there is a risk of faulty operation or noise due to vibrations.

   • When installing the insulator, make sure that it does not run over the protruding part.

   • Before installation, wipe off any oil or dirt on the casing.
     WARNING
     Do not place the unit within the reach of young children as the insulators could be swallowed accidentally. In the event that a part is swallowed, seek medical attention immediately.
     Rear
     
     

5. DC power connector
   Connect the AC adapter supplied with the unit.

6. USB connector (Type-B

Connection

Connecting the power cord

Caution

• Connect the power cord before connecting the unit to a computer.
• In the case of emergency (smoke, abnormal smells, strange noises, or similar), immediately remove the power plug from the outlet.

Connecting the USB cable

This unit can be added without shutting down or rebooting the computer. Connect the
unit to the supplied USB cable.

1. Confirm that your computer (PC) has available USB port.
2. With your Windows® or Mac® operating system running, use the supplied USB cable to connect this unit to the PC.

Caution

• Do not disconnect the USB cable during data transfers.
• Do not disconnect the USB cable during the PC start nor any operation with the unit.
  

Note

• It is recommended to connect to USB 3.0 port or above, , since when a USB 3.0 cable is connected to a USB 2.0 port, the connection will be limited to USB 2.0 performance standards.
• This unit can operate with USB 1.1 but will not provide optimum performance.
• Connecting this unit through a USB HUB or using unspecified cables may not guarantee proper operation.
• The unit will not run on power supplied from the USB connector (bus power). Be sure to use the unit with the AC adapter supplied with the unit connected.

Forcefully ejecting the disc

In the following situation, you can forcefully eject the disc by using the forced ejection hole.

• When the device has malfunctioned and the disc cannot be ejected using the eject button or through the software

1. Check that the computer power is turned off, and that the disc has stopped rotating.
2. Straighten a paper clip or similar object, and insert this straight into the forced ejection hole and push hard.
3. The disc tray will come out by 5 mm (3/16 in.) to 10 mm (25/64 in.), so pull out the tray and remove the disc.
   

Note

• Never forcefully eject the tray while the disc is still rotating, as doing so may lead to injury or damage to the disc.
• Do not place items within 12 cm (4- 23/32 in.) of the front of the device, as doing so may obstruct disc ejection.

Downloading and Installing CyberLink Media Suite (with Product Key)

• CyberLink® Media Suite is compatible with Windows® OS only. The application cannot be used with macOS® .

1. Visit the website shown on the back of this manual.
2. Review the License Agreement, and click “Agree” to proceed to the CyberLink webpage.

Download

1. After accessing the download website, sign in with your CyberLink member e-mail address and password.
   (If you have not registered as a CyberLink member, click “Register now” and register to be a member.)

2. After signing in, the product key input screen will be displayed. Enter the provided product key and click “Submit”.
   The product key is on the back of this manual. (The 16-character key printed on the label.)

3. If the product key has been entered correctly, the screen to download the downloader will be displayed. Click the download link to download the downloader.

Re-downloading the downloader
After registering the product key on the download website, an e-mail will be sent to your registered CyberLink member e-mail address.
The downloader can be re-downloaded from the Link in the e-mail for 30 days from registration of the product key

Installation

1. Connect the drive to Windows PC.
2. Run the downloaded file to start downloading the program.
3. After the download is complete, the installation message will be displayed in the dialog box. Click “Install” to start up the installer. (Even if you do not click “Install”, the installer will automatically start up after 1 minute.)
4. After the installer starts up, follow the instructions on the installer to install the product.

Useful Functions

These functions can be used if the Drive Utility is downloaded and installed. For details on other functions in the Drive Utility, refer to the drive utility help page. Please download the Drive Utility from the Pioneer website.
https://pioneer.jp/device_e/product-e/ibs/device_e/dev00001r_e.html#DriveUtility

Custom Eco function

Explanation of function

If the drive does not receive any commands (instructions for operation) from the PC for a specified period, this function will reduce the device’s power consumption (enter the power saving mode), such as by stopping the disc from rotating or reducing the disc rotation speed. Shortening this specified period will make the device enter the power saving mode earlier.

• If a command is received after entering the power saving mode, the device will require some time to bring the disc back up to high-speed rotation, which means a reduced speed of operation in the interim.

Using this function
Configure the setting in the “Pioneer BD Drive Utility.”

1. Install the “Pioneer BD Drive Utility.”

2. Start the “Pioneer BD Drive Utility.”

3. Click the [Utility] tab.
   

4. Slide the [ ] under [Custom Eco] to the [Power Save] side.
   There are 10 levels between the performance mode and power saving mode.

5. Select [Save setting to the drive].
   The set values will be saved to the drive. Settings will be retained even after turning off the device power.

Cautions in usage

• If power to the drive is turned off without selecting the [Save setting to the drive] checkbox, the settings will revert to the previously saved settings.

• In a Windows® environment, the setting can be changed at any time using the
  Pioneer BD Drive Utility, when the drive is recognized.

• Custom Eco settings can only be changed in Windows. After changing the settings in Windows, the device can be used with a Mac® .

PureRead

Explanation of PureRead function

When using this device to read a music CD, you can use PureRead. This function allows the device to work to acquire and reproduce the original sound as much as possible such as by repeatedly reading scratched or soiled parts of the CD. PureRead can be set to the following two modes or turned off.

Master Mode (default setting)| This mode works to acquire and reproduce the original sound as much as possible, but if it encounters audio data that cannot be completely reproduced, it interpolates that data and continueswith acquisition.
---|---
Perfect Mode| This mode reproduces the original sound, and if it encounters audio data that cannot be completely reproduced, it stops andhalts acquisition.
OFF| This mode carries out normal acquisition of music CD data. Ifthere is a scratch that prevents reading, interpolation will occur.

What is interpolation?

Audio data that cannot be read because of scratches or other damage is created by inference from sounds before and after it. This  sound will be degraded compared to the original sound.

Using PureRead

[Windows®]

1. Install the “Pioneer BD Drive Utility.”

2. Start the “Pioneer BD Drive Utility.”

3. Click the [Setting2] tab.

4. Select the [On] checkbox under [PureRead3+].

5. Select from either [Perfect Mode] or [Master Mode].

6. Select [Save setting to the drive].
   The set values will be saved to the drive. Settings will be retained even after turning off the device power.

[Mac®]

1. Install “Pioneer BD Drive Utility” (macOS® 10.14 or earlier) or “Pioneer BD
   Drive Utility Lite” (macOS 10.15 or later).

2. Start “Pioneer BD Drive Utility”or “Pioneer BD Drive Utility Lite.”
   When using “Pioneer BD Drive Utility Lite,” operate without a disc inserted.

3. Select the [On] checkbox under [PureRead].

4. Select from either [Perfect Mode] or [Master Mode].

5. Select [Save setting to drive].
   The set values will be saved to the drive. Settings will be retained even after turning off the device power.

Displaying PureRead mode

With the device not operating, press and hold the eject button for at least two seconds.
The busy indicator flashes, and the current PureRead mode setting is displayed.

Mode display

Cautions in usage

• The PureRead mode display function cannot be used while the device is operating.
• If power to the drive is turned off without selecting the [Save setting to the drive] checkbox, the settings will revert to the previously saved settings.
• Changing PureRead with the Drive Utility while using the PureRead mode display function causes the display to be incorrect.
• Ensure that the drive does not operate when pressing and holding the eject button.

Specifications

[Installation] The device can be installed horizontally or vertically.

[Disc size]
12 cm (4-23/32 in.) / 8 cm (3-9/64 in.)*
***** 8-cm (3-9/64 in.) discs cannot be used when the unit is installed vertically.

[Transfer rate]
Data reading (sustained)

BD: Max. 54.0 MB/s
DVD: Max. 21.6 MB/s
CD: Max. 7.2 MB/s

Data writing (sustained)

BD: Max. 72.0 MB/s
DVD: Max. 21.6 MB/s
CD: Max. 7.2 MB/s

Interface standards
USB 3.2 Gen1/2.0

• The transfer rate may be reduced depending on the condition (scratches, etc.) of the disc.

[Access time/Seek time]
Access time (random average)
BD 180 ms DVD 170 ms CD 160 ms

Seek time (random average)
BD 160 ms DVD 150 ms CD 140 ms

[Others]

• AC Input Power ………………………………………………………….. AC 120 V, 60 Hz
• Power consumption (Rating) …………………………………………………………….. 30 W
• No load power consumption ……………………………………………………………………. 0.1 W
• Dimensions (excluding foot pad) ……………… 160 mm (W) x 50 mm (H) x 220 mm (D) 6.30 inch (W) x 1.97 inch (H) x 8.66 inch (D)
• Weight (Drive only)………………………………………………….. 1.1 kg (Typ.) / 2.4 lbs
• Operating temperature ………………………………….+5 °C to +35 °C (41 °F to 95 °F)
• Operating humidity …………………………………………20 % to 80 % (no condensation)
• Buffer size…………………………………………………………………………………………… 4 MB

[AC Adapter]

• Dimensions (Body only)……………………89.8 mm (W) x 27.0 mm (H) x 37.8 mm (D) 3.54 inch (W) x 1.06 inch (H) x 1.49 inch (D)
• Weight ……………………………………………………………………. 0.15 kg (Typ.) / 0.33 lbs

[Accessories]

Owner’s manual (including warranty information and application product key)
USB cable (USB Type-A → USB Type-B) (1 m (3 ft. 3 in.))
Insulators for horizontal placement × 4
Insulators for vertical placement × 8
AC adapter (OWR8003-) (1.2 m (3 ft. 11 in.))
Power cord (0.5 m (1 ft. 8 in.))

Problems and Solutions

Unexpected errors in operation are often thought to be malfunctions. If you think there is a malfunction, check the items below according to the symptoms.
If the abnormality is not resolved even after taking the following measures, please contact your dealer or Pioneer.
Additionally, please consult with the application software manufacturer regarding any problems occurring in the application software.

The device does not operate

• Are the cables connected correctly?
  • → The drive power is turned on and off in conjunction with the power supply of the connected PC. Accordingly, connecting the device to an AC adapter and connecting to a USB port on a PC with the power turned on will turn the power supply on. Check that the USB cable and AC adapter are connected correctly

The computer or application does not correctly recognize the device

• Is the USB cable or AC adapter connected correctly?
  • → Make sure the cable is connected correctly. If you are using a USB hub, the power supply may be insufficient. Connect the USB cable directly to your  computer.
• Is the OS compatible with the device?
  • → Use an OS that supports this device. (Windows® 11, Windows 10, Windows 8.1, OS X El Capitan® 10.11, macOS Sierra® 10.12, macOS High Sierra® 10.13, macOS Mojave® 10.14, macOS Catalina® 10.15, macOS Big Sur® 11, macOS Monterey® 12)

The disc is not recognized

• Is the disc set correctly in place?
  • → Check that the disc is set correctly in place.

Data cannot be recorded/Error occurs during recording

• Is there sufficient space for recording?
• Check that the required application software is installed in the usage environment.
• Check that the operating environment being used meets the specifications for the application software being used.
• Recording on the disc at the selected speed is not possible.
  • → Check that the disc supports the different recording speeds.
  • → The speed may drop depending on the condition of the disc.
• Are you using a disc that has been finalized (no more recording is possible)?
• Is the disc correctly inserted with the label side facing up and the recording side facing down?
• Is the disc dirty or scratched?

A recorded disc cannot be read

• Is the disc inserted into the disc tray with the label side facing up?
• Are you using a blank disc?
• Is the disc dirty or scratched?
• Check that the required application software is installed in the usage environment.
• Is the device installed in a flat location?
• The optical components or disc may have condensation on them. Therefore, turn the device power off for a period of time and wait for it to fully dry before usage.

For other details on how to record on discs, refer to the manual or help screens for the application software being used.

For more stable disc recording and playback

The operating temperature range for this product is +5 °C to +35 °C (41 °F to 95 °F). However, recording and playback at normal temperatures is recommended in order to ensure stable recording as well as playback on various players and drives.

Region codes

The default region code of this drive is “1”. The region code for the drive can be changed only four times, and the region code set with the fourth change will be locked as the final region code. Accordingly, take care when changing this code

• DVD discs that do not have a region code set can be played on all players.

There are no images. There is no sound.

•  Digital output of BD-Video content (output using DVI or HDMI terminals) requires graphics functionality and monitors that support HDCP standards. Check that your PC environment supports HDCP standards. Playback of BD-Video content and other high-definition videos requires very high processing power. If you encounter phenomena such as frame dropping or choppy audio, it may be possible to prevent this by reducing the load on the PC, either by stopping resident software or using video playback support functionality in the graphics function. Review the operating environment and try playback again with as little load on the PC as possible from other applications. Playback of BD-Video content requires periodic updates to the playback software as the content decryption key has an expiration date. Before playback, ensure that the latest update from the software manufacturer has been applied.
• During DVD-Video title playback, if the playback software counter is counting correctly and audio is output but no images are displayed, check the resolution  and number of colors of your monitor. The standard settings are 800 x 600 resolution and 16-bit color. Additionally, check that the video card (video chip) drivers are the latest versions, and update if necessary If a message such as “Failed to create overlay” is displayed, this indicates insufficient video card performance as above, so set the resolution and number of colors as described above. Furthermore, if your PC has a TV output function, an error message starting with “Macrovision . . .” may be displayed. In these cases, turn off the TV output function.
• If images are displayed but no audio is output, the video may be being output in an audio format not supported by your playback software. Check the audio format recorded with the BD/DVD-Video title, and switch to a supported audio format (surround sound, etc.).
• Media and files such as videos from BD/DVD-Video and digital broadcasting include content protection, and have restrictions on copying and playback. Check that there are no restrictions on the content to be played and on the playback environment.

Others

Warranty and After-Sales Service

AFTER-SALES SERVICE FOR PIONEER PRODUCTS
Please contact the dealer or distributor where you purchased the product for its aftersales service (including warranty) or any other information. You may also contact Pioneer Customer Support at 1-800-421-1404 in the U.S. and Canada, or at the address listed below:
PLEASE DO NOT SHIP YOUR PRODUCT to the address listed below for repair. Units requiring service must be sent to a different address and with an RMA number. Please contact Pioneer Customer Support or an authorized service company if service is required for your product.
PIONEER ELECTRONICS (USA) INC.
P.O.BOX 1720, Long Beach, California 90801 U.S.A.

Questions about the included application software

Direct inquiries to the following software manufacturers.
CyberLink Support Center
https://www.cyberlink.com/support/index.html

Trademarks and registered trademarks

• Pioneer and the Pioneer logo are registered trademarks of Pioneer Corporation.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.
• Mac, OS X El Capitan, macOS, macOS Sierra, macOS High Sierra, macOS Mojave, macOS Catalina, macOS Big Sur and macOS Monterey are registered trademarks of Apple Inc.
• M-DISC is a trademark of Millenniata, Inc.
• BLU-RAY DISC, the Blu-ray Disc logo, BDXL and the BDXL logo are trademarks of the Blu-ray Disc Association.
• CyberLink is a trademark or a registered trademark of CyberLink Corporation.
• All other trademarks belong to their respective owners.

ONE YEAR LIMITED WARRANTY

(In the U.S. and Canada)

When purchased from an authorized Pioneer dealer, this product is covered by Pioneer’s One Year Limited Warranty. Please visit our website to review and download the full terms and conditions of the Limited Warranty, or you can receive a copy by calling 1-800-421-1404 or writing to the address below.
https://www.pioneerelectronics.com/StaticFiles/PUSA/Files/Warranty/PUSAOpticalWarranty.pdf

Customer Support, Pioneer Electronics (USA) Inc., P.O. Box 1720, Long Beach, California 90801 U.S.A.

RECORD THE PLACE AND DATE OF PURCHASE. KEEP THIS INFORMATION AND YOUR SALES RECEIPT IN A SAFE PLACE.

Model No. : BDR-X13UBK
Serial No. __
Purchase Date ___
Purchased From __

Website for downloading application
https://jpn.pioneer/cyberlink_soft/en.php

The downloader can be re-downloaded from the Link in the e-mail sent from CyberLink for 30 days from registration of the product key

CyberLink Media Suite
Product key for free download

© 2022 PIONEER CORPORATION. All rights reserved

PIONEER ELECTRONICS (USA) INC. P.O.BOX 1720, Long Beach, California 90801 U.S.A.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>