Qijun Toys Industry 1833-1-2-3 Multifunction Battle Remote Control Tank Instructions

Qijun Toys Industry 1833-1-2-3 Multifunction Battle Remote Control Tank

PARTS LIST

FUNCTION INTRODUCE

CHARGE INSTRUCTIONS

1. a. Before use the new battery, please charge it.
2. b. Connect the bettery and the charger, then plug the charger into the socket.(As shown in figure 1)
3. c. Fully charged need 90-150 minute. There have indicator light on the charging plug，the red light on and green light flash when charging, the green light on and red light off once fully charged. Don’t overcharge,this couldn’t increase the electric quantity.
4. d. Check the toys, batteries, charging wires and plugs regularly. If any of those accessories is damaged, stop using them until they are repaired or replaced.

FUNCTION INSTRUCTIONS

Frequency connection: Put the power switch of vehicle to “ON”, the light flash slowly and the vehicle into frequency connection model; and long press the switch button of the remote control at the same time, frequency connection succeed. The vehicle default drive modle, function can be normal control .

Battery Installation Instructions

• Remote control:
  • a. Please use a screwdriver to loosen the screws on the battery cover and open it.
  • b. Please put 2pcs 1.5V AA battery according positive and negative into the battery holder.
  • c. Close the battery cover and tighten the screws
• RC car:
  • a. Please open the battery cover on vehicle bottom, connect the built-in battery into the power interface and put into the batter holder.
  • b. close the cover and tighten the screws.

EVA BULLET TURRET

PARTS LIST

EVA BULLET TURRET FUNCTION INSTRUCTION

• Put eva bullet into ammunition clip.
• There have a arrow mark on the ammunition clip, make it face to the slot in the middle of the turret,hold down the ammunition clip into the turret.lift up to remove the ammunition clip.
• Connect the turret wire connection to the vehicle’s,there have a emboss on the side of turret connection port, put it into the hold in the side of the vehicle connection port, hold down the side button at the same time, and complete installation. Hold down the side button again and disconnect the wire connection between the turret and vehicle to remove the turret. Change other turret please repeat the preceding operations.
• Loading the infrared ray equipment to the turret, press the power switch, emit infrared.
• After frequency connection succeed, hold down the remote control left side button, the turret turn left;hold down the right side button, turret turn right.
• Turret shooting function: press button the turret shooting EVA bullet, press and hold the button, turret continuous fire.
• Under the voice control and one key demo modle, the shooting function of the turret would be continuous fire.

WATER BULLET TURRET

PARTS LIST

WATER BULLET TURRET FUNCTION INSTRUCTION

• Put some water bullet into container and add water,let it sit for a while,filter out the excess water in the bottle after the water bullet imbibe complete.
• Open the cover on the top of turret,put the water bullet in and close the cover.After the game, please take out the remaining water bombs in the magazine and clean the magazine. Reassemble play please repeat the above steps.Do not add water when adding water bomb to prevent circuit board short circuit.
• Connect the turret wire connection to the vehicle’s,there have a emboss on the side of turret connection port, put it into the hold in the side of the vehicle connection port, hold down the side button at the same time,and complete installation. Hold down the side button again and disconnect the wire connection between the turret and vehicle to remove the turret. Change other turret please repeat the preceding operations.
• Loading the infrared ray equipment to the turret, press the power switch, emit infrared.
• After frequency connection succeed, hold down the remote control left side button, the turret turn left; Hold down the right side button, turret turn right.
• Turret shooting function: press button the turret shooting water bullet, press and hold the button, turret continuous fire.
• Under the voice control and one key demo modle, the shooting function of the turret would be continuous fire.

BUBBLE TURRET

PARTS LIST

BUBBLE TURRET FUNCTION INSTRUCTION

1. Put some bubble water into the container(It is concentrated solution and could be add some water), close the cap.
2. Open the door at the back of turret, pull out two pieces hose inside, and put them into the bubble water container, and put the container into the magazine(as show in figure),close the door. Put the hoses into bottle as far as possible, and keep the hoses unobstructed to avoid squeezing and blocking affect the function. After the game, remove the container from the magazine and clean the magazine. Reassemble play please repeat the above steps.
3. Connect the turret wire connection to the vehicle’s, there have a emboss on the side of turret connection port, put it into the hold in the side of the vehicle connection port, hold down the side button at the same time, and complete installation. Hold down the side button again and disconnect the wire connection between the turret and vehicle to remove the turret. Change other turret please repeat the preceding operations.
4. After frequency connection succeed, hold down the remote control left side button, the turret turn left; hold down the right side button, turret turn right.
5. Turret shooting function: press and hold the button, turret continuous fire.
6. Under the voice control and one key demo modle, the shooting function of the turret would be continuous fire.

TANK (WATCH)

Watch Function Diagram

Function Introduce

• ON/OFF Key: Press the ON/OFF key to starting up the watch,the dail indicator light flash.After frequency connection succeed, the dail indicator light cycle flash and the watch into standby mode, to press ON/OFF key again,one or several indicator light on,vehicle enter drive modle. Short press ON/OFF key to switch standby/drive mode in the game, long press close the watch and indicator light off.
• Frequency Connection: Put the power switch of vehicle to “ON”, the light flash slowly and the vehicle into frequency connection model; and short press the ON/OFF key of the watch at the same time, frequency connection succeed, the dail indicator light cycle flash and the watch into standby mode, short press ON/OFF key again, one or several indicator light on, vehicle enter drive modle, the function can be normal control.
• Mode Switch:
• Shooting Function: keep shake the watch from side to side, the vehicle start shooting. (Shooting function can be operated in any mode)

Watch wearing diagram (right hand)

Charge Instructions(Below Picture).
After close the watch, use the supplied Android charging cable,connect the Micro port of chargeing line into USB charge port on the side of the watch and switch on the power. The dial red indicator light is on when charging, and the light off when fully charged.

FCC Compliance Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>