TURTLE BEACH Stealth 600 Gen 2 MAX Multiplatform Amplified Wireless Gaming Headset User Guide

QUICK START GUIDE

STEALTH™

600
GEN 2 MAX

IMPORTANT READ BEFORE USING

Any questions?
turtlebeach.com/support
Model: Stealth™ 600P Gen 2 MAX

IMPORTANT

PLEASE MAKE SURE YOUR HEADSET IS UPDATED WITH THE LATEST FIRMWARE.

Connect to the Turtle Beach Audio Hub for Windows or Mac® to update firmware.

turtlebeackcom/audiohub

CONTENTS

A Stealth™ 600 Gen 2 MAX Headset

B USB-A Wireless Transmitter

C USB-C Charging Cable

HEADSET CONTROLS

1. LED Indication
   Refer to LED Behaviors page

2. Master Volume Dial

3. Variable Mic Monitoring

4. MODE Button
   Cycle through audio presets
   (Refer to EQ presets table)

5. Power Button
   Press (2s) = Power On/Off
   When on, press = Superhuman Hearing'” On/Off

6. USB Charge & Update Port

Microphone Mute
Flip up mic to mute. There is an audible tone when the mic is muted or unmuted.

Use Superhuman Hearing™ Mode to pinpoint quiet audio cues like enemy footsteps and weapon reloads.

During gameplay, you can activate and deactivate Superhuman Hearing™ by pressing the POWER button once, quickly.

 
Mic Unmuted                  Mic Muted                    Mic Muted

  EQ PRESETS

Signature Sound
Bass Boost
Bass + Treble Boost
Vocal Boost

SETUP FOR PLAYSTATION® & NINTENDO SWITCH™

1 Put the transmitter into “PS” mode.

2 Connect transmitter to USB port.

1. Console’s USB Port

3 Power on headset.

4 Wait for headset & transmitter to pair.

5 Go to Settings > Sound > Audio Output > Output Device
a. Select Stealth™ 600 Gen 2 Max for Output Device
b. Set Output to Headphones to All Audio
c. Set Volume Control (headphones) level to Maximum

Adjust your microphone levels by going to Settings > Sound > Microphone > Adjust Mic Level > Microphone Level

On PS5™, enable 3D Audio to enhance through your headset, then go to Adjust 3D Audio Profile to select the best profile option for your game.

The Stealth™ 600 Gen 2 MAX supports Nintendo Switch wireless compatibility supported through USB connection while in docked mode only.
*Chat is available for games that support in-game chat capability while connected through the USB connection only.

SETUP FOR PC MODE

The Stealth™ 600 Gen 2 MAX’s PC mode optimizes the headset to operate on your PC. In this mode, your MODE button will sync with your multimedia to allow you to play and pause your music and skip tracks and adjust your master volume from your PC or keyboard.

Any EQ modes you selected in PS mode will also be carried over in PC mode.

1 Put the transmitter into “PC” mode.

2 Put the transmitter into your platform’s USB-A port.

3 Power on headset.

4 Wait for headset & transmitter to pair.

CHARGING

The Stealth™ 600 Gen 2 MAX gives you 48+ hours of recharge-able battery life. Make sure to charge it regularly before storing.

1. Console’s USB Port

Headset Storage
Always charge your headset before storing it for any extended period of time (longer than 3 months). Never store the unit in temperatures above 113°F/45°C.

RE-PAIRING

The headset and transmitter are paired out of the box , indicated by a solid LED on the wireless transmitter. If your transmitter’s LED is double- blinking , follow the steps to pair your headset and wireless transmitter.

1 Connect your transmitter into an available USB port on your console or PC. Your transmitter will double-blink blue as it searches to pair with your headset.

5 seconds

2 Power on your Stealth™ 600 Gen 2 MAX headset and the LED will begin to double-blink blue as it searches for your transmitter.

3 Within 10 seconds, the LED indication on the headset and the transmitter should turn solid blue to indicate a successful pairing.

If your transmitter cannot pair after 30 seconds, it will search for a previously paired headset or any available Stealth™ 600 Gen 2 MAX headset to pair to. Try bringing the headset closer to the transmitter to ensure a successful or faster pairing.

LED BEHAVIORS

LED turns off when battery is fully charged if headset is off.
Breathing Red| Battery Low

USB TRANSMITTER COMPATIBILITY

The USB-A wireless transmitter is equipped with a switch that allows you to change compatibility modes.

Regulatory Compliance Statements for Stealth 600P Gen 2 MAX

Models: Stealth600P-MAX-RX and Stealth600P-MAX-TX

Local Restrictions on Radio Usage
Caution: Due to the fact that the frequencies used by wireless devices may not yet be harmonized in all countries, these radio products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel. for the country of use. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such.

To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer’s OEM Regulatory Guidance document at the following http://www.turtlebeach.com/homologation or contact Turtle Beach directly.

Federal Communications Commission (FCC) Compliance Notices
This section includes the following FCC statements for Stealth600P-MAX-RX and Stealth600P-MAX-TX:

• FCC IDs: XGB-3160RX & XGB-3160TX
• Class B Interference Statement
• RF Radiation Exposure & Hazard Warning
• Non-Modification Statement

Class B Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful. interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Radiation Exposure & Hazard Statement
To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.) from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Non-Modification Statement
Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the Stealth600P-MAX-RX and Stealth600P-MAX-TX and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Please contact Turtle Beach for a list of approved 2.4 GHz antennas.

This product is compliant with the Consumer Product Safety Improvement Act of 2008, Public Law 110-3’14 (CPSIA)

Canadian ICES Statement:
IC: 3879A-3160RX & 3879A-3160TX

This device complies with ICES-003 and RSS-247 of Industry Canada. Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

To prevent radio interference to the licensed service (i.e. co-channel Mobile Satellite systems) this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing and not supported by models: Stealth600P-MAX-RX and Stealth600P-MAX-TX.

RF Radiation Exposure & Hazard Statement
To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

European Union and European Fair Trade Association Regulatory Compliance
This equipment may be operated in the countries that comprise the member countries of the European Union and the European Fair Trade Association. These countries, listed below, are referred to as The European Community throughout this document:

AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA, LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY, SWITZERLAND

Declaration of Conformity
Marking by this symbol:

indicates compliance with the Essential Requirements of the Radio Equipment Directive (RED) of the European Union (2014/53/EU). This equipment meets the following conformance standards:

Safety:
EN 62368-1: 2014 + Al 1 (T-Mark License),
IEC 62368-1: 2014 (CB Scheme Certificate),
EN 50332-1: 2013, EN 50332-2: 2013, EN 71-3: 2013
Additional licenses issued for specific countries available on request

EMC:
EN 55032: 2015 + Al 1 : 2020, CISPR 32: 2015,
EN 301 489-1 v2.2.3 (2019-11), EN 301 489-9 v2.1.1 (2019-04)
EN 61000-4-2: 2009, EN 61000-4-3: 2006 + Al : 2008 + A2: 2010,
EN 61000-4-8: 2010

The products are licensed, as required, for additional country specific standards for the International Marketplace. Additional issued licenses available upon request.

Radio: EN 300 328 v2.2.2 (2019-07)

SAR: EN 62311: 2020

Environmental : RoHS 2015/863 amending Annex II to 2011/65/EU, WEEE 2012/19/EU, REACH 2006/1907/EC, Packaging 94/62/EC, Battery 2006/66/EC, Toys Safety Directive 2009/48/EC

Please visit the following URL for a complete copy of the Declaration of Conformity: http://www.turtlebeach.com/homologation

Warning! This is a Class B product. In a domestic environment, this product may cause radio interference, in which case, the user may be required to take appropriate measures.

This symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.

Turtle Beach Europe Ltd is obligated as a producer with a main activity of selling under The Producer Responsibility Obligations (Packaging Waste) Regulations 2007. To fulfil our obligation we are registered with Comply Direct and their Recycling Room. Here you will find advice and information on packaging waste management, recycling symbols and the waste hierarchy principles of reduce, reuse and recycle. https://www.complydirect.com/the- recycling-room/

To access the rating Label:

1. Remove the left ear pad by pulling the ear pad straight up using your thumb.

2. Once you’ve released the cloth from the lip on top, pull the ear pad straight back and it should slip right off.

To replace the ear pad, follow the same process in reverse.

Not seeing what you’re looking for here?

Visit turtlebeach.com/support for the latest Tech Support information.

426-234-005-005 RC

PKG DESIGN DEPT

Designer: Taylor Swanson
Product: Stealth 600P Gen 2 MAX
Project: QSG
Date: 3 / 23 / 22
Scale: 100%

   COMMENTS

Please do not print this Layer!!!

• 100% actual size
• Refer to video on how to fold

SPECIFICATIONS

Printing information

**** BLK + WHT

**** QSG Paper Weight (80g)
Foldout

Folding Line

CHANGES

Orig Arena #: 426-234-005-005
New Arena #: 426-234-005-005 RO1 <(brent oliver)
Date / Initiator: 12/03/21 / CREATIVE
1. Converted Xbox to PlayStation.
New Arena #: 426-234-005-005 RA <(brent oliver)
Date / Initiator: 01/06/22 / CREATIVE
1. PVT.
New Arena #: 426-234-005-005 RB <(taylor swanson)
Date / Initiator: 02/14/22 / CREATIVE
1. Conversion to Unlicensed PS
New Arena #: 426-234-005-005 RC <(taylor swanson)
Date / Initiator: 03/24/22 / PdM
1. MP
2. Updates to copy per Erin S.
3. Translations placed 3-23-22

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>