Turtle Beach STEALTH 600 Gen 2 Wireless Gaming Headsets User Guide

STEALTH 600 Gen 2 Wireless Gaming Headsets
User Guide

IMPORTANT
PLEASE MAKE SURE YOUR HEADSET IS UPDATED WITH THE LATEST FIRMWARE.
Connect to the Turtle Beach Audio Hub for Windows or Mac® t o update firmware.
Connectez-vous au Turtle Beach Audio Hub pour turtlebeach.com/audiohub

CONTENTS

CHARGING

The Stealth™ 600 Gen 2 USB gives you 24+ hours of rechargeable battery life. Make sure to charge i t regularly before storing.

Headset Storage
Always charge your headset before storing it for any extended period of time longer than 3 months]. Never store the unit in temperatures above 113°F/45°C.

SETUP
Connect mini transmitter to USB Port
Itis recommended to insert the mini wireless transmitter in to the USB port at the front of the PS5™ console.

Go to Settings > Sound > Audio Output > Output Device
a. Select Stealth 600 Gen 2 USB for Output Device
b. Set Output t o Headphones t o All Audio
c, Set Volume Control (headphones) level te Maximum
Adjust your microphone levels by going to Settings > Sound > Microphone > Adjust Mic Level > Microphone Level On PS5™, enable 3D Audio t o enhance through your  headset, then go t o Adjust 3D Audio Profile to select the best profile option for your game.

SETUP FOR PC & SWITCH™

1. Put the transmitter into your platform’s USB-A port.
2. Power on headset.
3. Wait for headset & transmitter t o pair.

HEADSET CONTROLS

Use Superhuman Hearing™ Mode to pinpoint quiet audio cues like enemy footsteps and weapon reloads.
During gameplay, you can activate and deactivate Superhuman Hearing ™ by pressing the POWER button ence, quickly.
Microphone Mute
Flip up mic to mute. There is an audible tone when the mic i s muted or unmuted.

PRESETS
Signature Sound
Bass Boost
Bass + Treble Boost
Vocal Boost

RE-PAIRING

The headset and mini transmitter are paired out of the box, indica tedby as oli d LED on the mini transmitter. If your mini transmitter’s LED is double- blinking,  follow the steps to pair your headset and mini transmitter.
Connect your mini transmitter into an available USB port on your console. Your mini transmitter will double-blink blue as it searches to pair with your headset.

Power on your Stealth” 600 Gen 2 USB headset and the LED will begin to double- blink blue as it searches for your mini transmitter.
Within 10 seconds, the LED indication on the headset and the mini transmitter should turn solid blue to indicate a successful pairing.

If your mini transmitter cannot pair after 30 seconds, it will search for a previously paired headset or any available Stealth™ 600 Gen 2 USB headset to pair to. Try bringing  the headset closer to the mini transmitter to ensure a successful or faster pairing.

LED BEHAVIORS

is fully charged if headset is off.
Double-Blink Blue| Not Paired
Solid Red| ( While  Charging) Battery Charging
Breathing Red| Battery Low

Regulatory Compliance Statements for Stealth 600P Gen 2 USB
Models: Stealth600P-USB-RX and Stealth600P-USB-TX

Local Restrictions on Radio Usage
Caution: Due to the fact that the frequencies used by wireless devices may not yet be harmonized in all countries, these radio products are designed for use only in specific  countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products  are used only i n the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of  use. Any deviation from the permissible power and frequency settings for the country of use i s an infringement of national law and may be punished as such.
To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the  identification label of your device is listed in the manufacturer’s OEM Regulatory Guidance document at the following http://www.turtlebeach.com/homologation or contact Turtle Beach directly.

Federal Communications Commission (FCC) Compliance Notices
This section includes the following FCC statements for Stealth600P-USB-RX and Stealth600P-USB-TX:

• FCC IDs: XGB-3176RX & XGB-3176TX
• RF Radiation Exposure & Hazard Warning
• Class B Interference Statement
• Non-Maodificatian Statement

Class B Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radia frequency energy and, ifnotinstalled and  used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur i n a  particular installation. I f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  Consult the dealer or an experienced radio / T V technician for help.

FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.

RF Radiation Exposure & Hazard Statement 
To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.)  from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end  users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other  antenna or transmitter.

Non-Modification Statement
Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the Stealth600P-USB-RX and Stealth600P-USB-TX and violate  FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Please contact Turtle Beach for a list of approved 2.4 GHz antennas.

This product is compliant with the Consumer Product Safety Improvement Act of 2008, Public Law 110-314 (CPSIA] Canadian ICES Statement:
IC: 3879A-3176RX & 3879A-3176TX
This device complies with ICES-003 and RSS-247 of Industry Canada. Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

European Union and European Fair Trade Association Regulatory Compliance
This equipment may be operated in the countries that comprise the member countries of the European Union and the European Fair Trade Association. These countries,  listed below, are referred to as The European Community throughout this document:
AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND,  ITALY, LATVIA, LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN,  UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY, SWITZERLAND

Declaration of Conformity
Marking by this symbol:
indicates compliance with the Essential Requirements of the Radio Equipment Directive (RED) of the European Union (2014/53/EU).
This equipment meets the following conformance standards:
Safety: EN 62368-1: 2014 +A11 (T-Mark License),
IEC 62368-1: 2014 (CB Scheme Certificate),
EN 50332-1; 2013, EN 50332-2: 2013, EN 71-3: 2013
Additional licenses issued for specific countries available on request
EMC: EN 55032: 2015 + A11: 2020, CISPR 32: 2015,
EN 301 489-1 v2.2.3 [2019-11], EN 301 489-9 v2.1.1 (2019-04)
EN 61000-4-2: 2009, EN 61000-4-3: 2006 + A1: 2008 + A2: 2010,
EN 61000-4-8: 2010
The products are licensed, as required, for additional country specific standards for the International Marketplace.
Additional issued licenses available upon request.

Radio: EN 300 328 v2.2.2 (2019-07)
SAR: EN 62311: 2020
Environmental : RoHS 2015/863 amending Annex Il to 2011/65/EU, WEEE 2012/19/EU, REACH 2006/1907/EC, Packaging 94/62/EC, Battery 2006/66/EC, Toys Safety Directive 2009/48/EC
Please visit the following URL for a complete copy of the Declaration of Conformity: http://www.turtlebeach.com/homologation

** This symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose  of your waste equipment by handing it over toa designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and  recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.
Turtle Beach Europe Ltd is obligated as a producer with a main activity of selling under The Producer Responsibility Obligations (Packaging Waste] Regulations 2007. To  fulfil our obligation we are registered with Comply Direct and their Recycling Room. Here you will find advice and information on packaging waste management, recycling  symbols and the waste hierarchy principles of reduce, reuse and recycle. https://www.complydirect.com/the- recycling-room/
Mexican IFT-008 Compliance Statement**

To access the rating label:

1. Remove the leftear pad by pulling the ear pad straight up using your thumb.
   To replace the ear pad, follow the same process in reverse.

2. Once you’ve released the cloth from the lip on top, pull the ear pad straight back and it should slip right off.
   Not seeing what you ‘ re looking for here? Visit turtlebeach.com/support for the latest Tech Support information.

IMPORTANT
READ BEFORE USING
Any questions?
turtlebeach.com/support
Model: Stealth” 600P Gen 2 USB

Documents / Resources

| Turtle Beach STEALTH 600 Gen 2 Wireless Gaming Headsets [pdf] User Guide
3176TX, XGB-3176TX, XGB3176TX, STEALTH 600 Gen 2 Wireless Gaming Headsets, 600 Gen 2 Wireless Gaming Headsets, Gen 2 Wireless Gaming Headsets, Wireless Gaming Headsets, Gaming Headsets, Headsets
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>