SENA C1 Smart Cycling Helmet User Manual
- June 9, 2024
- Sena
Table of Contents
C1 Smart Cycling Helmet
User Manual
C1 Smart Cycling Helmet
Charging (The Bluetooth / LE function is not working while is charging.)
Red LED: Charging Blue
LED: Fully charged
Power On/Off
Power On : Press and hold the (+) Button and Center Button for 1 second
Power Off : Tap the (+) Button and Center Button.
Volume Adjustment
(+) Button – Increase the volume
(-)Button – Decrease the volume
Battery Check
Phone, Music Pairing
Initially Pairing the C1
The Bluetooth system will automatically enter the phone pairing mode when you
initially turn on the Bluetooth system or in the following situation:
- Rebooting after executing Factory Reset
- Press and hold the Center Button and (+) Button for 1 second.
- Search for Bluetooth devices on your mobile phone. Select the C1 in the list of the devices detected on the mobile phone.
- Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
Music Operation
Play or pause music: Press the Center Button for 1 second.
Track back: Press the (-) Button for 1 second.
Track forward: Press the (+) Button for 1 second.
Mobile Phone Call Making and Answering
Answering a call: Tap the Center Button
Ending a call: Press the Center Button for 2 seconds.
Voice dial: Press the Center Button for 3 seconds.
Speed dial: Press the (+) Button for 3 seconds.
Rejecting a call: Press the (+) Button for 2 seconds.
Intercom
Intercom Pairing
- Press and hold the Center Button of two headsets for 5 seconds until red LEDs of both units start to flash rapidly.
- Simply tap the Center Button of any one of the two headsets.
Intercom Start/End : Tap the Center Button
LED Taillight
LED On and Solid -> Night Flash -> Day Flash -> LED Off : Press the (-) Button for 1 second.
Setting
Configuration Menu: Press the Center Button for 15 seconds.
Troubleshooting
Factory Reset
If you want to restore the headset to factory default settings, use the
Factory Reset in the configuration menu. The headset automatically restores
the default settings and turns off.
Certification and Safety Approvals
FCC Compliance Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antennae
- Increase the separation between the equipment and the receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. The antenna used for this
transmitter must not transmit simultaneously with any other antenna or
transmitter, except in accordance with FCC multi-transmitter product
procedures.
When equipped, the distance between antenna and one’s head surface is 21.5 mm.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void user’s authority to operate the
equipment.
CE Declaration of Conformity
This product is CE marked according to the provisions of the R&TTE Directive
(1999/5/EC). Hereby, Sena declares that this product is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
For further information, please consult www.sena.com.
Please note that this product uses radio frequency bands not harmonized within
EU. Within the EU this product is intended to be used in Austria, Belgium,
Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The
Netherlands, Portugal, Spain, Sweden, United Kingdom and within EFTA in
Iceland, Norway and Switzerland.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This device can be operated in at least one Member State without infringing
applicable requirements on the use of radio spectrum.”
– RF Range: 2402 ~ 2 480 MHz (Bluetooth/LE)
– Max Power : BT: Max. 16.51 dBm(eirp),
LE: Max. 4.92 dBm(eirp) BT: Max. 16.69 dBm, LE: Max. 3.62 dBm
Trade name: SENA