Abask J05 Front+Inside 1080P Dual Dash Cam User Manual

: June 9, 2024
: Abask

FHD Dual 1080P
J05 Dash Cam

User Manual
N0.:513230104185

Quick Start Guide

What’s in the Box?

1dash cam with cabin cam
1suction cup
1cigarette lighter adapter (3.5m)
1mini USB cable (0.5m)
132GB Micro SD card (Memory card has been inserted in the dash cam)
1crowbar 4cable clamps
1user manual

Installing the Camera

Check if the memory card is in the camera.
Attach the suction cup bracket to the camera.
Plug the charging cable into the USB port on the suction cup, and then plug the adapter into the cigarette lighter socket of your car. Start the car and the camera will turn on automatically.

The blinking red dot on the screen means the camera is recording video, press OK button first to pause the recording.
Press the MENU button twice to enter the system menu. Please make the following initial settings.

Set the language. Press the RIGHT button to select the language, press OK button to enter the setting. Press the RIGHT or LEFT button to select the language, press OK button to confirm and return to the system menu.
Set the date and time. Press the RIGHT key to select the date and time, and press OK to enter the setting. Press to the RIGHT or LEFT to adjust the number, press OK to confirm and go to the next item. Press MENU button to return to the system menu.
Format the memory card. Press the RIGHT button to select format, press OK to enter the setting. Press the RIGHT button to select OK, press OK to confirm the formatting and return to the system menu.

Press MENU to return to the standby mode. Press the OK button and the camera starts working.

Important Notice

Caution

Ensure you are using your dash cam within your countries road laws. Please make sure you are familiar with your local road legislation before use.
Avoid leaving your dash cam in direct sunlight for extended periods of time in unventilated space.
The system is to be used only for non-commercial use, within the limits permitted by the relevant laws.
Avoid using the dash cam in the vicinity of any devices that emit radio interference (eg. Microwave Ovens).
It is considered normal operation for the dash cam to get warm during use.

Warm Tips

To access the menu settings, please press the OK button to stop the video recording first.
Please format the memory card in the camera menu at the first use.
Please set time and date before you use this dash cam to record.
This camera records video at high resolution.Be sure to use a high-speed Micro SD card (Class 10 or above,max supports 64GB.)
For safety reasons,the built-in battery is only used for emergency backup files.The dash cam is powered by the car.The car camera will automatically switch on/off when the car engine ignition is on/off.
To work,the dash cam must be connected to the car’s cigarette lighter socket or hardwired to the car’s fuse box.
The video from the front camera can be reviewed directly from the dash cam or PC, but what was recorded by the inside camera can only be reviewed through PC.
Therefore, please connect the camera to the PC by the attached USB cable or just remove the memory card and read it on PC to review all the footage. ·To use the parking monitoring function, please use the cable kit “Dash Cam Hard wire Kit Mini USB”.

Battery Warning

The built-in battery is only used for emergency backup. Always charge the dash cam using the provided charger. Improper charging of the dash cam may result in failure of the internal battery.
Never dismantle the dash cam or expose the internal battery,
Do not dispose of the dash cam in fire.
Dispose of the dash cam observing local regulations being mindful of the internal battery.

Interface and Button Function

Recording Interface

The camera will automatically enter Video Recording Mode and start recording when connected to a car charger and power on. A Red dot flashing on the top left corner indicates record is in progress. Press the OK to stop recording, or start recording again. The following are icon representations of some common functions on the screen, indicating that these functions are enabled.(You can also find their representations through the menu accordingly).

1. Recording Mode
2. Loop Recording
3. Exposure
4. Motion Detection
5. HDR| 6. G-sensor
7. Recording Time
8. Resolution
9. Parking Monitor
10. LED Light Status| 11. Memory Card Status
12. Power Status
13. Audio Status
14. Time & Date
15. Recording Status
---|---|---

Camera Overview

Front Camera Lens: Record a video of the front of the car.
Microphone: Records clear audio.
LCD Screen: 1.5 inches TFT Color LCD Display.
IR LED Lights: 4 IR LED lights enhances the night vision in car.
Inside Camera Lens: Rear facing camera for in-car video recording.
Mini USB Port: USB port for charging or transferring data.
Mount Connector: Connects to the Suction Cup Mount.
Power Button: Power ON/OFF
OK button: Confirms the action; Stop/Start the video recording.
◄ button: Move selector up.
MENU button: Enter/exit setup menu.
► button: Move selector down
Reset Hole: Press to force reset the device
Memory Card Slot: Provides expandable storage (Card has been insert in)
Speaker: Delivers sound during video playback.

Button Function

Power| • Long press to turn ON / OFF the camera power.
• Press to turn/off the screen.
---|---
OK| • In video mode, press to start/ stop video recording
• In camera mode, press to take a photo.
• In menu setting, press to confirm selection and adjustment.
• In playback mode, press to select and play recorded files.
◄
LEFT| • In menu setting, press to select option.
• In standby mode or video recording modes, press to switch front and inside display views.
• In playback mode, press to select media files.
• Long press to turn on/ off the LED light for the inside camera.
MENU/
MODE| • In standby mode, press to access the menu settings, and press twice to access System Setting Menu.
• Return function: Press to return to the previous page.
• In standby mode, long press to switch mode between Video / Photo / Playback.
• During video recording, long press to lock/ unlock the current footage.
►
RIGHT| • In menu setting, press to select option.
• In playback mode, press to select media files.
• During video recording, press to turn on/ off audio recording while long press to on/ off parking monitor function.

Specification

Model	J05
Video Resolution	1080FHD/720P/VGA
Photo Resolution	VGA/1M/2M/3M/5M/8M/10M
Screen	1.5 inch LCD Display
Angle	170° High-Resolution Wide Angle Lens
Video Resolution	Front : 1920 * 1080P(highest)

Getting Started

Check the Memory Card

Please insert the SD card in the correct direction. The SD card will pop out after pressing it with a fingernail or sharp object. (SD card is already inserted in the SD card slot)

To remove the memory card
Ensure that the dash cam is powered off,then push the memory card until a click is heard and then release the card to eject.

Note:

Do not remove or insert the memory card while the dash cam is turned on as this may damage the memory card or corrupt the memory card’s stored data.
Please use a Class 10 or higher rated micro SD card with a maximum capacity of 64GB.
Please format the Micro SD card before the initial use.

Installing the Dash Cam

Insert the high-speed TF card (Class10 or above) into the card slot of the dash cam. (You need to format the TF card in the dash cam when you use it for the first time)
Remove the protective stickers from the dash cam and the Suction Mount.
Attach the Suction Mount to the camera’s Mount Connector, pushing it in until it clicks.
Securely attach the Suction Mount to the windshield, plug the car charger into the car cigarette lighter, and the other end into the USB port of the dash cam. (The charging extension cable can be laid along the edge of the car windshield when wiring.)
Adjust the device position: Loosen the knob on the right hand side of the mounting bracket, and adjust the vertical and horizontal angle of the camera. To make sure you get the best coverage over the hood and the road ahead, so you can record what happens. Tighten the knob to lock the position of the camera.
Start the car. The camera will auto power on and start recording.

Powering the Dash Cam On /Off

Auto Power On/Off
Install and connect the dash cam to your vehicle’s power supply properly. The dash cam switches on / off automatically when the engine ignition of the vehicle is switched on / off.

Manual Power On/Off
(1)Manual Power On
Hold the Power button until the start up screen appears.
(2)Manual Power Off
Make sure that recording has been stopped(no red dot flashing on the screen). Press the power button of the dash cam for 10 seconds to turn off the camera.

Reset the Device
If the dash cam does not function normally,try restarting the dash cam. Please insert a flattened paper clip into the “R” hole on the side of the dash cam for 5 seconds, then release it. The dash cam will restart.

Initial Settings

Before using the dash cam we recommend Formatting the Inserted Micro SD Card, setting the correct Language, Time and Date. After setting the initial settings, Press MENU to return to standby mode. Press the OK button to start the camera operation.

Set the Language

Press the OK key to stop the recording and press the MENU key to enter the system menu twice.
Press the RIGHT button to select the language option and press the OK to enter the language setting.
Press the RIGHT or LEFT button to select your language, press OK button to confirm and return to the system menu.

Set the Date and Time
Setting the Time and Date allows you to stamp your footage with the time as a reference.

Press the OK key to stop the recording and press the MENU key to enter the system menu twice.
Press the RIGHT key to select the date and time option, and press OK to enter the setting.
Press to the RIGHT or LEFT to adjust the number, press OK to confirm and go to the next item.
Press MENU to return to the system menu.

Format the Memory Card
Formatting the Micro SD card will delete all information on the inserted Micro SD Card and prepare the card for use with the dash cam.

Press the OK key to stop the recording and press the MENU key to enter the system menu twice.
Press the RIGHT button to select the format option, and press OK to enter the setting.
Press the RIGHT button to select OK, press OK to confirm the formatting and return to the system menu.

Note:

Menus cannot be accessed while the camera is recording. Please stop the recording before attempting to access the menu. (The blinking red dot on the screen means the camera is recording video).
Formatting your Micro SD Card will delete all files from the card.Once these files have been deleted you will not be able to recover them.
After setting the initial settings, Press MENU to return to standby mode. Press the OK button and the camera starts working.

View the Recorded Videos

Playing Back Video on dash cam

Press the [OK] button to stop recording (no red dot flashing on the screen)
Press and hold the [MENU] button for 3 seconds to enter photo mode, and press and hold the [MENU] button again for 3 seconds to enter video playback mode.
Select a video by pressing the LEFT and RIGHT keys.
Press OK to play the video.

Playing Back Video on a PC

Connect the dash cam to the computer using the USB cable(included).
“Mass Storage” “PC camera” and “REC mode” will be displayed on the camera screen, please navigate to “Mass Storage” and press the OK button to transfer data.
Click the folder “DCIM” in the storage disk on your computer to view your recorded video.

Note:

File 1 is the video taken by the front camera. File 2 is the video taken by the inside camera. The name “SOS” is a locked video. Name “VID” is an unlocked video.
To playback video files on your PC it is recommended to connect the Micro SD card directly to your PC using either a USB Micro SD card reader (not included) or if your PC has an SD card slot, a Micro SD/SD Card converter(not included). Once the Micro SD card is connected it should appear as a removable storage device. It is recommended that you transfer video files that you want to playback to a file on your computer before attempting to playback. This will reduce any delay in playback.

Operating Mode

The dash cam operates in 3 modes: Video Recording Mode, Photo Mode and Playback Mode. These modes also have the menu to help you configure recording.
Long press the MENU button to switch between different modes and access the mode you want. Watch the icon on the top left corner of the screen for each mode. In all 3 operating modes you can press the [MENU] button once to access the menu settings for that particular model, and press it twice to display the System Setting Menu.
The System Setting Menu is common to all modes.
Press ◄ and ► to scroll through the various setting options and press OK to select and confirm selection, Press [MENU] again to exit the setting menu.

Video Recording Mode

The camera will automatically enter Video Recording Mode and start recording when connected to a car charger and powered on.
A Red dot flashing on the top left corner indicates recording is in progress. Press the OK to stop recording or start the recording again.

Locked Recording
Lock Recording saves the current video file and prevents it from being overwritten. When the car encounters a collision, the G-sensor detects the vibration and the camera automatically locks the video.
To manually activate locking video, follow the instructions below.

During recording press the MENU button.
To unlock the footage, press the MENU button again.

Video Recording Menu
When the camera was paused, (there was no red dot flashes in the upper LEFT corner), and press Menu to enter the video recording menu settings.
Resolution: Adjust front camera recording video resolution 1080FHD / 720P / VGA, the inside camera will keep recording at 1080P.
Loop Recording: Continuously record small video files of a length which is determined by the settings off/ 1/ 2/ 3 Minutes. For example, if it is set for 3 minutes, the camera will automatically save a section of videos every 3 minutes. When the memory gets full, the dash cam will automatically delete the oldest video to record the latest video, which can avoid a lack of memory.

High Dynamic Range: HDR, Turn on to optimize video quality with wider light range and image details.
Exposure: Exposure is used to manually control the light sensitivity settings. The default is 0.
Motion Detection: Motion Detection is used to pause recording when no motion is detected in front of the camera, and to start recording when motion is detected again. Default is off.
Recording: Turn ON / OFF audio recording in the video. Default is on.
Date Stamp: Enable/Disable the date and time marks in video files.

G-Sensor(Gravity Sensing)
The G-Sensor defines the required force needed to trigger emergency recording. Once Emergency recording is triggered the current recording will be saved and protected from being saved over by the normal loop recording. To set the required sensitivity please follow the instructions below.

Press the【OK 】Button to stop the dash cam from recording.(no red dot flashing on the screen)
Press the【MENU】Button to enter the Video Menu.
Press the【MENU】Button again to enter the Settings Menu.
Press the [◀ ] or [▶ ] button to select the Gravity Sensing setting option,select 【OK】to confirm .

Note:

Menus cannot be accessed while the camera is recording. Please stop the recording before attempting to access the menu.
The default setting of G Sensor is off.
If your memory card is filling up quickly you may need to lower the sensitivity of the G-Sensor (Gravity Sensor)to decrease the number of triggers caused by normal driving. It’s better to set G-Sensor to “Medium” to avoid too many useless locked videos.

Parking Monitor
It’s used to protect your car after parking. With this function on, after you stop the car and the camera turns off, it stays standby. When camera detects shock and collision, it will automatically turn on and take a short video, then shut down automatically.

Note:
To set Park Monitor Mode, follow the instructions below.

Ensure that the dash cam is not recording.
Press the[MENU]Button to enter the Video Menu.
Press the [◀ ] or [▶ ] button to select the Parking Mode setting option, select [OK] to confirm.
To use this function when the car is parked, please buy a hard-wire kit(mini USB type)for dash cam then connect to the vehicle’s fuse box power so as to supply the power to the camera.

If you have any questions, please contact the after-sales email.

Setting System Menu
Press MENU button twice to access System Setting Menu in any mode. The TOOL icon is highlighted in the upper LEFT corner.

Screen Saver: Set the timing to automatically turn off the LCD display after no operation so as to have the product worked in very low power consumption; There are “Off, 30s, 1 Min, 2 Min” in this setting. For example, if it is set “30s”, the screen will turn off after 30 seconds, but the camera is still working(recording). When you want to turn on the screen, you can press any button to activate the screen.

Auto Power Off: Set the time for the dash cam to automatically shut down to save power. The dash cam will automatically shut down when it is in standby for the set time. (Off/1min/3min/5min)
Frequency: Set light frequency to 50HZ or 60HZ according to local regulation. If the camera interferes with the radio, try changing the frequency.
Beep Sound: Turn on / off sound that when pressing any button made.
Language: Choose the camera system language (Chinese/English/French/German/Italian/Spanish /Japanese.)
Date/Time: Set the time and date. Press the LEFT and RIGHT keys to adjust the numbers, then press the [OK] button to confirm/change, and press the [MENU] button again to exit the time setting.
Format: Completely delete all files in the storage card.
Restore Setting: Reset all settings back to factory default.
Version: The firmware version of the dash cam.
LED Light: Set up the IR LED lamp working mode for the inside camera, On/ Off or Auto. In Auto mode, the IR LED will light when the light inside the car is too dark.

Photo Mode

Press the OK Button to stop the dash cam from recording.(no red dot flashing on the screen)then long press the mode [MENU] button to enter the photo mode. In the photo mode, press the [OK] button to take pictures and save.
This mode is for manual operation only.

Resolution: Set the photo resolution.
VGA/1M/2M/3M/5M/8M/10M for choices.

Anti-shaking: Turn on / off image stabilization function.
Date Stamp: Date stamp will stamp the current date onto the image files for future reference.

Playback Mode

This mode allows you to playback recorded video or view photos, and manage the recorded files.

Press the [OK ]Button to stop the dash cam from recording.(no red dot flashing on the screen), long press the MENU button twice to enter Playback Mode, you can view all the files in this mode.
Use the LEFT and RIGHT button to scroll through the recorded files / photos, and press OK to play or pause playing the selected file.
Press the MENU key to enter the file menu. You can delete or protect video files.
Delete: Delete the current file displayed or delete all files.
Protection: Lock / Unlock the current file displayed or lock /unlock all files.
Long Press MENUENU button to quit playback and return to standby mode.

Problems and Answers

Can’t get to the menu?
When the camera is recording video, the menu button does not work. A flashing red dot on the screen means the camera is recording video. Please press OK to pause recording, then Press MENU to enter the menu.
The dash cam will stop automatically when recording.
Solution:
1. Check whether the memory is full.
2. Check whether the loop recording function of the dash cam is working.
3. Check whether the Micro SD card is high-speed above U3.
4. Playback the recorded video on dash cam to check whether there might be to many locked videos, which cause the SD card space run out and stop looping recording. If yes, please format the SD card.
5. Check the car charger connection status, if the connection is loose, the power supply is not stable, the power supply is not stable, the camera will automatically turn off.
6. Check whether it is just because of the Screen Saver on.
If the video played on the computer is somehow jammed or not fluent. There might be the problem with the memory card speed.
Solution:

Format your Micro SD card in the camera.
Change a U3 or above high-speed Card.

There are stripes interference in the video. Or radio is disturbed.
Solution:
There should be wrong light frequency. According to the local main frequency, make the appropriate settings 50HZ or 60HZ.
Suction mount cannot attach on windshield well?
Solution:

Please clean the windscreen where attaching with a glass cleaning wipe. Removed the protective film, If it does not work, warming your windscreen then try it again.
Please soak suction mount to warm water for a moment.
If it is still not working, we are glad to send a new suction mount to you, please contact us to get a replacement.

The internal battery, despite receiving a one-night charge, barely lasts a few minutes? /Without external power supply, the camera only lasts very short time, or just can’t turn on?
Solution:
The built-in battery is only to save files urgently in case of sudden power off. The dash cam is powered by the car. The car camera will automatically switch on/off when the car engine ignition is on/off. No need to charge the dash cam or worry about the battery level. It is not designed to work without external power supply, so please keeps the camera connecting to car’s cigarette lighter socket, while you starts the car, your car is supplying power to the dash cam, the dash cam will turns on and record video. However, once the car turns off, the dash cam will turn off and stop recording as well. If you don’t want to connect the cigarette lighter, you can also hard wire the camera to the car’s fuse box. Please purchase a “dash cam hard wire kit”(mini USB type) separately.
The camera keeps turning on and off repeatedly.
Solution:

Please check if the charging cable is well connected.
Please insert a paper clip into the “R” hole on the side of the camera for 3 seconds, then release. The camera will restart automatically.
Please format the memory card in the menu.
Please check if the camera is back to normal.

How does the recorder work after it crashes?
Solution: If the machine crashes for some reason during use, please insert a paper clip into the “R” hole on the side of the camera for 3 seconds, then release. The camera will restart automatically.
Have set loop recording, but only randomly records for seconds with a long gap in between, then stops and re-start the recording.
Solution:
We suggest not turn on motion detection features while driving, this function may make recording intermittent.
The SD card gets full and it doesn’t overwrite?
Solution:
Please check whether all video files are locked( if locked, there will be a “key” icon at the top LEFT on the screen when you replay the files ). Those locked files cannot be overwritten by loop recording while needed to be delete manually, please format micro SD card and adjust sensitivity of G-sensor.
Why I can’t see records of the inside camera when I playback through the camera?
Solution:
What was recorded by the inside camera can only be reviewed through PC. Therefore, please connect the camera to the PC by the attached USB cable or just remove the memory card and read it on PC to review the footage.
If I see an accident which I’m not part of but it’s been captured by the camera, how can I save that recording?
What button would I press?
Solution:
If so, you need to manually lock the video to protect it from overwriting, there are 2 ways:
(1)Please long press the MENU button to lock the current recording video, you will see a “key” icon appear on the screen;
(2) Or stop the car, but still let the car start( to power the dash cam), and then playback the video, find the related video, press MENU button to protect it.
The parking monitor does not work?
Solution:
All dash cams on the market are powered by the car. After the dash cam is plugging in the car cigarette lighter socket, while starting the car, the car will supply power to the dash cam, the dash cam will turn on and record the video. However, once the car shuts down, the dash cam shuts down and also stops recording. Therefore, it does not react to movements and impacts after the engine is switched off. Therefore, if you want to activate the dash cam to monitor your car after the car shuts down during overnight parking, the dash cam needs to be wired to the car’s fuse box. Please purchase a “dash cam hard wire kit” (mini USB type) separately.

Warranty Policy

Warranty Period

We warrants to the original purchaser for the following period from your purchasing date against deficiencies in material and workmanship under normal use. Should this unit fail to operate in a satisfactory manner within the warranty period, we will, at its discretion, replace or repair the product.

Main Dash Cam: 12 Month
All Accessories: 12 Month
Micro-SD Card: 6 Month

Extended warranties are available. If you join our extended warranty program, you will get a 2 year warranty.
If you need it, please contact our after -sales service center.

After-sales Service

If your device cannot run normally, or you need technical support or help, please contact our after-sales service center at any time. We will reply you within 24 hours and provide you with a 100% perfect solution.
From US: supportus@abask.hk
From EU/UK: supporteu@abask.hk

What this warranty does not cover

If the device was not purchased from an authorized retailer.
Device malfunction due to the normal wear and tear, misuse, lack of maintenance, accidents, modification, alteration or repairs by an unauthorized person or entity.
Products that are operated in combination with ancillary and/or peripheral equipment not furnished or otherwise certified by for use with the product or any damage to the products or ancillary and/or peripheral equipment as a result of such uses.
We is not liable for any damages (properties, business, and/or indirect damages), loss or corruption of data for any reason, product damage or personal injuries that occur due to accidents or natural disasters.
Dash Cam records and saves video of vehicle accidents. It does not, however, guarantee to record all accidents. Accidents with a light impact that is not enough to activate the impact detection sensor may not be recorded.