HINKLEY 1321 27 Inch Tall 1 Light Outdoor Post Lamp Instruction Manual

: June 9, 2024
: HINKLEY

Table of Contents

1321 27 Inch Tall 1 Light Outdoor Post Lamp
Post mounting Instructions PMSS-1
I.S. 18 wiring grounding instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

1321 27 Inch Tall 1 Light Outdoor Post Lamp
Instruction Manual HINKLEY 1321 27 Inch Tall 1 Light Outdoor Post
Lamp Assembly Instructions
Item No. 1321

1321 27 Inch Tall 1 Light Outdoor Post Lamp

Find a clear area in which you can work.
Unpack fixture and glass from carton.
Carefully review instructions prior to assembly.

* The construction of this ﬁxture will be accomplished by ﬁrst installing the glass, making all necessary electrical connections, and then mounting the ﬁxture to the pole.
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Make electrical connections from supply wire to fixture lead wires. Refer to instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to continue installatio of this fixture.
NOTE:** It is recommended to lamp fixture prior to installing the glass.

To install, replace, or lamp the fixture, it is necessary to remove the upright (1). This is identified by the phillips screw (2) that attaches the upright to the top of the fixture – see drawing 1.
Drawing 1 – Glass Installation
Using a phillips screw driver remove screw (2) from the top of upright (1). Now gently pull upright (1) off of the fixture.
NOTE: do not twist, pull upright at both ends and pull evenly.
After upright (1) is removed, glass (3) can be slipped into place. To accomplish this, slip the top of the glass (2) into the cylindrical roof (CR) of the fixture and gently compress the tension spring (TS) located inside the cylindrical roof (CR).
Compress the tension spring (TS) until bottom of glass (3) can be slipped over the center hub (4) located on top of the post fitter (PF). Slip glass passed hub (4) and into position on top of the three remaining uprights.
Slip previously removed upright (1) back over support brackets (SB), making sure screw hole is at the top.
Replace screw (2) to secure upright.

PLEASE NOTE: ADDITIONAL CLEAR PLASTIC GROMMETS (CPG) HAVE BEEN SUPPLIED WITH THIS FIXTURE. THEY CAN BE SLIPPED OVER THE BOTTOM EDGE OF THE GLASS WHERE IT CONTACTS THE UPRIGHT.
1. To mount fixture to installed post follow post mounting instructoin sheet (PMSS-1) provided.

Post mounting Instructions PMSS-1

Find a clear area in which you can work.
Unpack ﬁxture and glass from carton.
Carefully review instructions prior to assembly.

* The installation of this luminaire will be accomplished by ﬁrst making all necessary electrical connections, mounting luminaire body to installed post, and then completing assembly.
NOTE:** it is recommended that steps 1 and 2 be done prior to installation of the glass or before any assembly is done on the fixture body.

To begin installation it will be necessary to drill 3 pilot holes in the installed post in order to mount the fixture body. This is accomplished by sliding the post fitter (1), of the fixture body (2), over the installed post.
Using the holes (3), in the side of the post fitter, mark the mounting hole locations – see DRAWING 1.
Drawing 1 – Post Mounting
NOTE: MAKE SURE FIXTURE BODY IS ORIENTED IN THE POSITION YOU WANT, BEFORE MARKING THE HOLE LOCATIONS.
Now remove fixture body from installed post and drill a 5/32” (4mm)dia. hole at the marked locations.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
NOTE: MAKE SURE ALL WIRE CONNECTORS USED ON ELECTRICAL CONNECTIONS ARE SILICONE FILLED.

Now follow instruction sheet (IS-18) make all necessary wiring connections.
After wiring is complete slip post fitter (1) of fixture body (2) over installed post and align holes in post fitter (1) with previously drilled holes in the installed post. Now thread in the three sheet metal screws (4) provided, to secure fixture body to the post.

I.S. 18 wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS
Wiring instructions
Indoor Fixtures

Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
Drawing 1 – Flush Mount
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector – – – see Drawings 2 or 3.
Drawing 2 – Chain Hung
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Cover open end of connectors with silicone sealant to form a watertight seal.
If instal ling a wall mount ﬁxture, use caulk to seal gaps between the ﬁxture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a ﬁxture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

Grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the ﬁxture ground wire (E) (typically copper or green plastic coated) to the ﬁxture mounting strap (M) with the ground screw (S) – see Drawing 1.
Drawing 3 – Post-Mount
HINKLEY 1321 27 Inch Tall 1 Light Outdoor Post Lamp - fig
5 Note: On straps for screw supported ﬁxtures, ﬁrst install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop ﬁxture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on ﬁxture mounting strap (M) and connect to the loose end of the ﬁxture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.
Post-Mount Fixtures
Connect ﬁxture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.