Hotpoint NT M11 8X3K Tumble Dryer User Guide

Hotpoint NT M11 8X3K Tumble Dryer

THANK YOU FOR BUYING A HOTPOINT PRODUCT. In order to receive more complete assistance, please register your product on www.hotpoint.eu/register

Before using the appliance carefully read the Safety Instructions.

CONTROL PANEL

1. ON/OFF Button (Reset if long pressed)

2. Programme Selection Knob

3. Start/Pause Button
   Options Buttons

4. Active Care

5. Dryness Level

6. Start Delay

7. Timed Drying

8. Cycle End

9. Gentle (Key lock if long pressed)

10. Crease Care (Mute if long pressed)

INDICATORS

FIRST TIME USE

Make sure that the water tank is correctly inserted. Make sure that the drain hose on the back of the dryer is properly fixed, either to the dryer’s water tank or to the domestic sewage system. The dryer must be installed in a room with a temperature ranging between 5°C and 35°C to ensure proper operation. Before you use your dryer ensure that it has been in an upright position for at least 6 hours. Should you wish to change the opening side of the door, please contact our After-sales Service. (See phone number in the warranty booklet).

DAILY USE

Doing this will keep your machine working at its BEST! Remember to empty your water tank after each drying cycle. Remember to clean your filters after each drying cycle. (Refer to section Care & Maintenance).

1. Open the door and load garments. Always refer to instructions on clothing labels and the max loads indicated in the program section. Empty pockets. Make sure garments do not get caught between the door and/or the door filter.
2. Close the door.
3. Press the button On/Off.
4. Select the program according to the laundry type.
5. Select the options, if necessary.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on the control panel signals the end of the cycle. Pull the load out immediately to prevent the formation of creases on the laundry.
8. Turn the machine off by pressing the button On/Off, open the door, and pull clothing out. If the machine is not switched off manually, after about a quarter of an hour from the cycle end, the appliance turns off automatically to save energy. If this last stage is not carried out immediately, some machines and/or some programs/options are equipped with the Crease Care system. For some hours, after the end of drying, the drum rotates at regular intervals to prevent the formation of creases. In case of power failure, it is necessary to press the button Start/ Pause to restart the cycle.

OPENING OF THE DOOR DURING THE CYCLE

During operation, it is possible to open the door. After having closed it, press the button Start/Pause again to restart the dryer.

PROGRAMMES

• Mixed kg 4
  This program is ideal for drying cotton and synthetic fabrics together.

• Eco Cotton kg Max
  The standard cotton program is suitable to dry normally wet cotton laundry. Most efficient program in terms of energy consumption for drying cotton laundry. The values on the Energy Label are based on this program.

• Synthetics kg 4
  This program is suitable for synthetic garments or cotton blends/synthetic.

• Wool kg 1
  Program for drying wool clothing. It is advisable to turn the garments inside out before drying. Leave to dry naturally the heaviest edges that are still damp.

• Silk kg 0,5
  Gentle drying of silk garments.

• Anti Allergy kg Max
  This cycle has the “Allergy UK” approval of “The British Allergy Foundation” attesting to the effective reduction and elimination of allergens. It can be used both with a damp load (drying and treatment) and a dry load (half load only).

• Daily kg 2
  Ideal for drying garments of cotton blends or synthetics spun at high speed in the washing machine.

MAX LOAD 8 Kg (Dry load)

CARE LABEL

Always check the care labels, especially when placing garments in the tumble dryer for the first time. Below are the most commonly used symbols;

1. Maybe tumble-dried.
2. Do not tumble dry.
3. Tumble dry – high heat.
4. Tumble dry – low heat.

The duration of these programs will depend on the size of the load, types of textiles, the spin speed used in your washer, and any extra options selected. In machines equipped with a display, the duration of the cycles is shown on the control panel. The remaining time is constantly checked and adjusted during the drying cycle to show the best possible estimate.

• Cuddly Toys Kg 2,5
  The cycle preserves the original appearance and brilliance of the cuddly toys at best. Remove all accessories before proceeding with drying. Every single piece must not exceed 600 gr.

• Pre-Iron
  This cycle allows to extension of the fibers of garments thus making ironing and folding easier. Do not use it in case of garments that are still wet. Suitable for small loads of cotton textiles or cotton blends.

• Refresh
  A short program suitable for refreshing fibers and garments by means of fresh air. Do not use it with garments that are still wet. It can be used with any load size but is more effective with small loads. The cycle duration is about 20 minutes.

• Duvet
  Programme intended to dry bulky garments, as a single duvet.

• Bed & Bath Kg Max
  This program is intended for drying cotton towels and sheets.

• Baby kg 2
  A program intended to dry garments and linen of newborn babies (cotton and chenille), as well as delicate garments. Do not dry garments having plastic covering.

• Jeans kg 3
  For drying cotton jeans-wear and garments made of robust cottons, like denim, such as trousers and jackets.

• Shirts kg 3
  This is a program for Shirts made from cotton or cotton blend/synthetics.

OPTIONS

After selecting the program, the various options can be set, if necessary.

• Active Care: This function allows for preserving the original appearance and brilliance of your garments at best, by controlling the motor speed, the rotation of the drum, and the temperature.
• Dryness Level: Press the related button several times to obtain a different level of residual moisture on garments. An indicator signals the level being selected.
• Iron Dry: very delicate ironing. Suitable for making the ironing of garments easier immediately after the end of the cycle.
• Hanger Dry: a level intended for delicate garments ready to be hung.
• Cupboard Dry: the garments are ready to be folded and put away.
• Extra Dry: used for garments to be worn at the end of the cycle.

Start Delay
This option allows you to set the delay of the cycle start. Press the corresponding button several times to obtain the required delay. After having reached the max. settable time, the option is reset by pressing the button again. An indicator on the control panel signals the time being selected. After having pressed the button Start/Pause, the machine signals the remaining time for the cycle to start. In case of the door opening, after closing, it is necessary to press the button Start/Pause.

• Timed drying: This option allows setting the drying time. Press the corresponding button to set the required time for drying. An indicator on the control panel signals the time being selected.
• Gentle: Enables a more gentle treatment of the laundry by reducing the drying temperature.
• Key Lock: This option makes all machine controls inaccessible, except the button On/Off.

When the machine is on:

• to activate the option, keep the button pressed until the indicator goes on.
• to disable the option, keep the button pressed until the indicator goes off. This option remains in memory if selected in the previous drying.

Crease Care
This option adds a crease treatment at the end of the cycle by means of a periodic rotation of the drum (duration of up to 10 hours). It is particularly suitable when it is not possible to remove the laundry as soon as the drying ends. If this option is used together with the Start Delay, the crease treatment is added also in the Start Delay phase. This option remains in memory if selected in the previous drying.

Mute
This option turns off all sounds of the control panel. Only warnings remain active. To activate the option, keep the button pressed until the indicator goes on. To disable the option, keep the button pressed until the indicator goes off.

Cycle End
This option activates a prolonged buzzer at the end of the cycle. Enable it if you are not sure to hear the normal sound at the end of the cycle. This option remains in memory if selected in the previous drying.

OPTIONS BUTTONS
These buttons serve to personalize the selected program according to personal requirements. Not all options are available for all programs. Some options are incompatible with the ones previously set. The buzzer and/or blinking indicators will signal the incompatibility. If the option is available, the option indicator will stay on. Some options may be kept in the memory of the program if selected in the previous drying.

CARE AND MAINTENANCE

Unplug the dryer during the cleaning and maintenance procedures. Emptying the water tank after each cycle (see Fig. A). Pull the container out of the dryer and empty it into a sink or other suitable drain, then place it back. Do not use the dryer without having inserted the container back in place. Cleaning the door filter after each cycle (see Fig. B). Pull the filter out and clean it by removing the lint from the filter surface under running water or using a vacuum cleaner. For optimal performance, dry up all the filters before inserting them back in place. Do not use the dryer without having reinserted the filter in place.

Remove the door filter as described below:

1. Open the door and pull upwards.
2. Open the filter and remove lint from all its parts. Replace it correctly.

Ensure it is completely inserted flush with the dryer seal. Cleaning the bottom filter when the relevant indicator turns on (see Fig. C). Pull the filter out and remove the lint from its surface by washing it under running water or by using a vacuum cleaner. However, it is advisable to clean this filter after each cycle to optimize drying performance. Do not use the dryer without having inserted the filter in place first.

Remove the bottom filter as described below:

1. Open the lower door.
2. Take the handle and pull the lower filter out.
3. Open the rear side of the filter and remove the lint from the inner surface of the mesh.
4. Clean the bottom filter chamber avoiding direct contact with the leaves.
5. Close the rear side of the lower filter and place it back by checking it is perfectly integrated into place.
6. Lower the filter handle and close the bottom door.
7. Make sure the air intake is free.

The filters are essential parts for drying. They are intended to collect the lint formed during the drying process. In the case of clogged filters, the airflow inside the dryer would be seriously affected: the drying times would be longer, the energy consumption would increase and the dryer could be damaged. If these procedures are not carried out properly, the dryer may not start.

TRANSPORT AND HANDLING

Never lift the dryer by holding it at the worktop.

1. Unplug the dryer.
2. Make sure that door and water tank are properly closed.
3. If the drain hose is connected to your sewage system, fix the drain hose on the rear of the dryer again (see Installation Guide).

Power consumption

off-mode (Po) – Watts| 0.50
left-on mode (Pl) – Watts| 1.00
Programs| Kg| kWh| Minutes
Eco Cotton ***| 8| 1.42| 165
Eco Cotton| 4| 0.78| 96
Synthetics*| 4| 0.94| 113
This is the reference program for the energy label and is suitable to dry normal wet cotton laundry. This is the most efficient program in terms of energy consumption for drying wet cotton laundry. (Standard/Default starting configuration).

Heat Pump System
The heat pump contains fluorinated greenhouse gases, contained in a hermetically sealed unit. This sealed unit contains 0.43 kg of the F gas R134a. GWP = 1430 (1 t CO2).

Product Description

1. Water bottle
2. Air Intake
3. Bottom filter
4. Door filter

TROUBLESHOOTING

Before contacting the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in a few minutes.

The tumble dryer does not turn on.

| The plug is not inserted into the socket.| Insert the plug into the socket.
The plug is faulty.| Try to plug another appliance into the same socket. Do not use connecting electrical devices to the socket, as adapters or extensions.
A power failure occurred.| Await the reactivation of the power supply.

The tumble dryer does not start.

| The door is open.| Close the door.
A time delay for the cycle start was set.| For machines equipped with this function: await the end of the delay set or switch the machine off to reset it. Refer to the section Options.
The button Start/Pause was not pressed to start the program.| Press the button Start/Pause.
The function Key Lock was enabled (in the case of machines equipped with this option).| Refer to the options section and, if the Key Lock is present, disable it. Switching the machine off is not enough to disable this option.

The drying times are very long.

| Appropriate maintenance was not carried out.| Refer to the section Care & Maintenance and perform the operations described.
The program, the time, and/or the drying level set are not suitable for the type and the amount of load inserted into the dryer.| Refer to the section programs and options to find the program and the options most suitable for the type of load.
The garments are too wet.| Carry out a washing cycle with a higher spin speed to remove as much water as possible.
The dryer may be overloaded.| Refer to the program section to check the max. load for each program.
Room temperature.| The drying time may be longer if the room temperature falls outside the 14–30°C range.
The program did not end.| A power failure occurred might have occurred.| In case of power failure, it is necessary to press the button Start/Pause to restart the cycle.
Program finishes and clothes are dampers than expected.|

Small load.

| The automatic program has not sensed the required final moisture and the dryer will complete the program and stop. If this happens simply select an additional short period of drying or select the extra dry option if available.

Lights on or flashing

Water tank| The water tank is full.| Empty the water tank. Refer to the section Care & Maintenance.
---|---|---
Door filter and/or bottom

**filter***

| Failure of the airflow necessary for machine operation.| Clean the door filter and the bottom one and check whether the air intake is free. Carrying out these operations improperly may cause damage.
Bottom **filter*| The bottom filter requires cleaning.| Clean the bottom filter. Refer to section Care & Maintenance.
DEMO**

The cycle lasts a few minutes.

| ****

The dryer is in DEMO mode. The DEMO indicator is on.

| Disable the DEMO mode. The following actions must be carried out in sequence, without breaks. Switch the machine on and then switch it off again. Press the Start/Pause button until the buzzer is heard.

Switch the machine on again. The “DEMO” indicator flashes and then

turns off.

The presence of a wrench

symbol signals a malfunction.

| ****

The machine sensors detected a failure.

| Switch the dryer off and unplug it. Open the door immediately and pull the laundry out, to allow the heat to dissipate. Wait for about 15 minutes. Reconnect the dryer to the power supply, load the laundry, and restart the drying cycle. If the problem still occurs, contact the After-Sales Service Centre and communicate the letters and digits flashing on the display.

For instance: F3 and E2.

Note: some models are self-cleaning and not equipped with a bottom filter. Please refer to the section Care & Maintenance.

You can download the Safety Instructions, User Manual, Product Fiche, and Energy data by:

• Visiting our website – docs.hotpoint.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
• When contacting our After-sales Service, please state the codes provided on your product’s identification plate.

FAQ’s

Why does the Hotpoint dryer take so long to dry things out?****

If you notice that your Hotpoint Condenser dryer is drying clothes slowly, there may be too much fluff in the condenser. At the bottom of your appliance is where you’ll find the condenser. Just remove it by holding the bottom cover by the sides and gently pulling it away from you.

What is the energy efficiency of a Hotpoint dryer?****

The Hotpoint Active Care NT M11 8X3K Tumble Dryer is committed to preserving the fabrics you love. It has a family-sized 9kg capacity, programmers designed to keep your clothing vibrant longer, and an A+++ Energy Rating to help you save money.

How long does a Hotpoint washing machine take to complete?****

WASH A FULL LOAD IN JUST 45 MINUTES.

How long does a Hotpoint wash cycle last?****

If you wash a 9 kg load of clothes on this kind of cycle, you should plan on waiting around four hours and ten minutes for the cycle to finish.

Have Hotpoint washing machines had any issues?****

Obstacles in the pump, the pump hose, or a blockage in the drain pump could all cause drainage problems, or another issue with the lid switches assembly. Overflowing: The water entry valve or pressure switch may be damaged.

Why does a load in my Hotpoint washer take so long to finish?****

There could be a problem with the load sense mechanism or more serious problems with the control panel if a washer frequently takes too long to complete a load.

What about the Hotpoint washer?****

Hotpoint washing appliances are excellent for households and laundry lovers seeking high-performance machines at a reasonable price.

What does the time saver feature on the Hotpoint washing machine do?****

Time saver this option will reduce the wash cycle by up to 50%, depending on the cycle you select, ensuring that both water and energy are conserved.

A rapid wash requires what temperature?****

While rapid wash frequently features a warm or cold wash setting, washing your things on a different setting, like cotton, will cause hot temperatures to be used.

What is the flow rate of the washer?****

For showers, 1.5–3 GPM. The dishwasher operates at 2-4 GPM, and the washing machine at 3 to 5 GPM.

How long does it take a Hotpoint washer to spin?****

The washing machine simply needs 5 to 10 minutes to spin.

What is the normal Hotpoint washing machine warranty?****

Your Hotpoint big appliance is fully covered for a full year by our own parts and labor warranty.

What volume of water does a Hotpoint washer use?****

The Hotpoint NT M11 8X3K consumed 24.67 gallons for the Heavy cycle and 31.5 gallons for Permanent Press.

Can I pause my Hotpoint washing machine in the middle of a cycle?****

Press the “Start/Pause” button on the front of the appliance before your washing machine unlocks the door, and then wait a few minutes for the washer to thoroughly drain the water in the drum.

How hot ought a quick wash to be?****

In general, 30°C washing is extremely effective. Because most quick wash cycles use the cold wash setting, this is also the best option for revitalizing lightly stained clothing that isn’t too filthy and simply needs a sparkle.

Download this PDF Link:Hotpoint NT M11 8X3K Tumble Dryer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>