dahua DH-HAC-HFW1200TL-A Network Bullet Cameras User Guide

**dahua DH-HAC-HFW1200TL-A Network Bullet Cameras User Guide

**

Waterproof Requirements

Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures.

NOTE the cables that you don’t use.

• Please use self-adhesive waterproof tape (supplied with some products) to protect the cables.
• Use waterproof components to protect the network cable. Waterproof the
  power cable separately if you don’t use it. The video cable does not need waterproof treatment.

1. Use insulation tape (not included in the package) to insulate the connection part of each cable.
   

2. Waterproof the cables with self-adhesive waterproof tape.

3. Fully stretch the waterproof tape at both ends.

4. Wrap the connection part and the cable ends tightly with waterproof tape. Make sure the tape isfully stretched during the process.

5. Tighten the tape at both end prevent water leakage.
   Wrap the used cables separately

Wrap the unused cables together into a bundle

3. Install the supplied waterproof componentsto the network cable in sequence.
   
   CAUTION!
   You need to mount the rubber ring onto the network cable interface first.

4. If your camera has a DC cable and you will not use it, insert the plug into the interface.

5. (Optional) After the waterproof treatment is completed, put the cables into a waterproof junction box (purchased separately).

CAUTION

• Restore and fasten the device after dismounting.
• Place the power adapterin a power distribution box.

Packing List

Contact your local dealer if the package is damaged or incomplete. The package contents may vary with device model.

Safety Instructions

Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the safety instructions before installation and operation.

Precautions

• Use a power adapter or a PoE device that meets requirements. Otherwise, the device may be damaged.
• Make sure the length of the power cable between the power adapter and the camera is not too long, otherwise the voltage of the camera is lowered, causing the camera to work abnormally. If it is required to lengthen the power cable, lengthen the cable between the power adapter and the mains.
• Do not overbend the cables during the installation, otherwise, poor cable contact may causemalfunction.
• When connecting to an external interface, use an existing connection terminal, and ensure that the cable terminal (latch or clamp) is in good condition and properly fastened. Ensure that the cable is not tense during mounting, with a proper margin reserved to avoid poor port contact or loosening caused by shock orshake.
• During transportation, special attention is required to protect the transparent dome cover from friction, scratchandstain, etc.Do notre move the protective film from the cover until mounting is finished. Remove the protective film before powering on the device.
• Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair ormaintenance

Maintenance

• • If there is dust on the front glasssurface, remove the dust gently using an oil-free brush or a rubber dust blowing ball.
• If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the center outward using anti-static gloves or an oil-free cloth. If the grease or the stain still remains, use anti-static gloves or an oil-free cloth dipped with detergent and clean the glasssurface gently until itis clean.
• Do not use organic solvents (such as benzene and alcohol) to clean the transparent dome cover.

Appearance

Dimensions

The following figure shows device dimensions. The appearance may vary with device model.

Cables

The appearance and tail cable may vary with device model.

NOTE

• For specifications, see the latest product datasheets.
• Press and hold the RESET button for at least 15 seconds to restore factory default settings. Perform this operation within 10 minutes after the device is powered on or the reset will fail otherwise.

Mount Your Camera

(Optional) Insert the Micro SD Card

Forcameras that support Micro SD, you need to insert the Micro SD card  after opening the bottom cover of camera. Do not hot plug the Micro SD card after it is inserted. Otherwise the camera or the SD card might be damaged. For recommended SD card specifications, please contact your dealer or technical support.

1. Loosen the cross-recessed screws to open the bottom cover.

2. Insert the Micro SD card.

Wall Mount

You can adopt wall mount or ceiling mount and purchase hardware accessories by yourself. The following part takes wall mount as an example. Ceiling mount is similar to wall mount and therefore is omitted here.

1. Locate the positions of the holes.
   Paste installation positioning stickers on the wall and align the cross center to the hole in the wall.
   Lead the cables across the hole on the wall.

2. Drill holes on the wall.
   Use a Ø6-6.5mm drill bit.
   Drill 30 mm-depth guide holes according to the positions marked by stickers

3. Mount the plastic rivets of self-tapping screws.
   Knock the plastic rivets into the guide holes and ensure that they are tightened up

4. Screw the locknut to loosen the universal joint before attaching your camera to the wall.

5. Mount your camera onto the wall and connect all cables
   Lead tapping screws through the guide holes in the base and fix them on the wall by using ascre wdriver.

6. Attach the rubbersheath to the antenna.

7. Rotate the antenna to the antenna interface according to clockwise direction.

8. Adjust the monitoring direction.
   Adjust the opening of the universal joints asrequired. Rotate the spherical hinge of the camera to get the desired monitoring direction. Tighten the locknut.

NOTE
The preceding installation process is for concealed installation, during which holes are punched on the wall and cables are penetrated into the wall. If open installation is adopted, cables are not penetrated into the wall but threaded outfrom the outlet on one side of the base.

Access Your Camera

1.  Open your Web browser, enter the camera’s IP address in the address bar, and then press Enter. The defaultIPis192.168.1.13(subne tmask is 255.255.255.0).
   2. In the loginpage, enterthede faultus ernameand password(admin/123456),th n click Login.

NOTE
DHCP is enabled by default. If a DHCP server is used in your network, your camera may be assigned an IP address, and you need to use the assigned IP address to log in.

• You may need to install a plug-in at your first login. Please follow the on-screen instructionsto complete the installation and then open the browser again to log in.
• The default password is intended only for your first login. To ensure security, please change the password after your first login. You are strongly recommended to set a strong password of at least nine characters including all three elements: digits, letters and special characters.
• If the password has been changed, please use the new password to log in.

About This Manual

• This manual is intended for multiple product models, and the photos, illustrations, descriptions, etc, in this manual may be different from the actual appearances, functions, features, etc, of theproduct.
• This manual is intended for multiple software versions, and the illustrations and descriptions in this manual may be different fromthe actual GUI and functions ofthe software.
• Despite our best efforts, technical or typographical errors may exist in this manual. cannot be held responsible for any such errors and reserves the right to change the manual without prior notice.
• Users are fully responsible forthe damages and lossesthat arise due to improper operation.
• reserves the right to change any information in this manual without any prior notice or indication. Due to such reasons as product version upgrade or regulatory requirement of relevant regions, this manual will be periodically updated.

Disclaimer of Liability

• To the extent allowed by applicable law, in no event will be liable for any special, incidental, indirect, consequential damages, norfor any loss of profits, data, and   documents.
• The product described in this manual is provided on an “as is” basis. Unless required by applicable law,this manual is only forinformational purpose, and allstatements, information, and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for a particular purpose, andnoninfringement.
• Usersmust assume totalresponsibility and allrisksfor connecting the productto the Internet, including, but not limited to, network attack, hacking, and virus.b    vstrongly recommends that users take all necessary measures to enhance the protection of network, device, data and personal information. disclaims any liability related thereto but will readily provide necessary security relatedsupport.
• To the extent allowed by applicable law, in no event shall total liability to you for all damages for the product described in this manual (other than as may be required by applicable law in cases involving personal injury) exceed the amount of money that you have paid for the product.

Network Security

Pleasetake all necessary measures to enhance network security foryour device.
T he following are necessary measures for the network security of your device:

• Changedefaultpasswordandset strongpassword:
  Youare stronglyrecommendedtochange thedefault passwordafter yourfirstloginandseta strongpasswordof atleastninecharacters including allthree elements: digits, letters and special characters.

• Change password regularly: Change your device password on a regular basis and keep the password safe. Make sure only the authorized user can log in to the    device.

• Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and ensure data  security.

• Enable IP address filtering: Allow access only fromthe specified IP addresses.

• Minimum port mapping: Configure your router or firewall to open  a minimum set of portsto the WAN and keep only the necessary port mappings. Never set the   device as the DMZ host or configure a full coneNAT.

• Disabletheautomaticloginandsavepasswordfeatures: If multiple users have accessto your computer,itisrecommendedthat youdisable thesefeaturestopreventunauthorizedaccess.

• Chooseusernameandpassworddiscretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case yoursocial media, bank and email account information is leaked.

• Restrictuserpermissions: Ifmore than one user needs accessto yoursystem,make sureeach user is granted only the necessary permissions.

• Disable UPnP: When UPnP is enabled, the router will automatically map internal ports, and the system will automatically forward port data, which results in the  risks of data leakage. Therefore, it is recommended to disable UPnP if HTTP and TCP port mapping have been  enabled manually on yourrouter.

• SNMP:Disable SNMP if you do not use it. If you do use it,then  SNMPv3 isrecommended.

• Multicast: Multicast is intended to transmit video to multiple devices. If you do not use this function, it isrecommended you disable multicast on your network.

• Check logs: Check your device logs regularly to detect    unauthorized access or abnormal operations.

• Physical protection: Keep the device in a locked room or cabinet to prevent unauthorized physical access.

• Isolate video surveillance network: Isolating your video surveillance network with other service networks helps prevent unauthorized access to devices in your security system from other service networks. Learn More You may also obtain security information under Security Response Center at official website.

Safety Warnings

The device must be installed, serviced and maintained by a trained professional with necessary safety knowledge and skills. Before you start using the device, please read through this guide carefully and make sure all applicable requirements aremetto avoid danger and loss of property. Storage, Transportation, andUse

• Store or use the device in a proper environment that meets environmental requirements, including and not limited to, temperature, humidity, dust, corrosive   gases, electromagnetic radiation, etc.
• Make sure the device issecurely installed or placed on a flatsurface to prevent falling.
• nless otherwise specified, do not stackdevices.
• Ensure good ventilation in the operatingenvironment. Do not coverthe vents on the device. Allow adequate space forventilation.
• Protectthe device from liquid of any kind.
• Make sure the powersupply provides a stable voltage that meetsthe power requirements of  the device. Make sure the powersupply’s output power exceedsthe   total maximum power of   all the connecteddevices.
• Verify thatthe device is properly installed before connecting itto  power.
• Donotremovethesealfromthe device bodywithout consultingfirst.Donotattempt to service the product yourself. Contact a trained professional for  maintenance.
• Always disconnectthe device from power before attempting to  move the device.
• Take proper waterproof measuresin accordance with requirements before using the device outdoors

Power Requirements

• Install and use the device in strict accordance with your local electricalsafety regulations.
• Use a UL certified powersupply that meets LPS requirements if an  adapter is used.
• Use the recommended cord set (power cord) in accordance with the specified ratings.
• Only use the power adaptersupplied with your device.
• Use a mainssocket outlet with a protective earthing (grounding) connection.
• Ground your device properly ifthe device isintended to be grounded.

Battery UseCaution

• When battery is used, avoid:
• Extremelyhighorlowtemperatureandairpressure duringuse,storage andtransportation.
• Battery replacement.
• Usethe batteryproperly. Improper useofthe battery such asthe followingmay cause risks of fire, explosion or leakage of flammable liquid or gas.
• Replace battery with an incorrecttype.
• Dispose of a battery into fire or a hot oven, ormechanically crushingor cuttingof a battery.
• Dispose ofthe used batteryaccording to yourlocalregulations orthe batterymanufacturer’s instructions

FCC Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interferencethat maycause undesired operation. Caution: The useris cautionedthat changesormodifications notexpresslyapprovedbytheparty responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the useris encouragedto try to correctthe interference by one ormore ofthefollowingmeasures

LVD/EMC Directive

This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU, 2014/53/EU.

WEEE Directive–2012/19/EU

The produc this manualreferstois coveredby theWasteElectrical&Electronic Equipment(WEEE)Directive andmust be disposedofin a responsiblemanner.

Battery Directive-2013/56/EC

Battery in the product complies with the European Battery Directive 2013/56/EC. For proper recycling, return the battery to your supplier or to a designated collection point. ****

Documents / Resources

| dahua DH-HAC-HFW1200TL-A Network Bullet Cameras [pdf] User Guide
V6012WB, CCK-V6012WB, CCKV6012WB, DH-HAC-HFW1200TL-A Network Bullet Cameras, DH-HAC-HFW1200TL-A, Network Bullet Cameras, Bullet Cameras, Cameras
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>