HINKLEY 41063BLK Four Light Pendant Instruction Manual

: June 9, 2024
: HINKLEY

Table of Contents

41063BLK Four Light Pendant
Assembly Instructions 41063
I.S. 18 wiring grounding instructions
Documents / Resources

41063BLK Four Light Pendant
Instruction Manual

41063BLK Four Light Pendant

IS-30-2 Convertible Canopy Assembly

THIS FIXTURE CAN BE MOUNTED CLOSE TO CEILING, TO PREPARE FIXTURE FOR MOUNTING FOLLOW THESE INSTRUCTIONS.
Flush mount mounting

To mount fixture as a flush first locate short stem (7)
Next insert threads of stem into canopy (2)
Place flat washer (6) and safety cable (5) on to stem
Secure stem to canopy using lock washer (4) and hex nut (3)
Fixture can now be wired and mounted

Pendant mount mounting

To mount fixture as a flush first locate the canopy swivel (S)
Next insert threads of swivel (S) into canopy (2)
Place flat washer (6) and safety cable (5) on to swivel
Secure swivel to canopy using lock washer (4) and hex nut (3) -Drawing (2)
Fixture can now be wired and mounted

Assembly Instructions 41063

Find a clear area in which you can work.
Unpack ﬁxture and glass from carton.
Carefully review instructions prior to assembly.

Shut off electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.
– DO NOT restore current – either by fuse, breaker, or switch – until the new fixture is completely wired and in place.

STEP 1

Feed wire through stem (S) or stems and canopy (C).
Secure stems together if needed. Note fixture is supplied with multiple stem not all stems have to be used. Fixture can be mounted as a flush
Secure bottom stem (S) to nipple (Z) at the top of of fixture
Secure top stem to canopy
Fixture mounting can now be started

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Make electrical connections form supply wire to ﬁxture lead wires.
Refer to instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete installation of this ﬁxture.

I.S. 18 wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

Wiring instructions
Indoor Fixtures

Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector – – – see Drawings 2 or 3.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Cover open end of connectors with silicone sealant to form a watertight seal.
– If installing a wall mount ﬁxture, use caulk to seal gaps between the ﬁxture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a ﬁxture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

Grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the ﬁxture ground wire (E) (typically copper or green plastic coated) to the ﬁxture mounting strap (M) with the ground screw (S) – see Drawing 1.
Note: On straps for screw supported ﬁxtures, ﬁrst install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop ﬁxture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on ﬁxture mounting strap (M) and connect to the loose end of the ﬁxture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.
Post-Mount Fixtures
Connect ﬁxture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.

HINKLEY 33000 Pin Oak Parkway, Avon Lake, OH 44012
800.446.5539 / 440.653.5500
hinkley.com