Schneider Electric TM5SDM12DT Electric Modicon TM5 Discrete Instruction Manual

Schneider Electric TM5SDM12DT Electric Modicon TM5 Discrete

TM5SD…

• TM5SDI.D
• TM5SDI.A
• TM5SDI6U
• TM5SDO.T
• TM5SDO.TA
• TM5SDM12DT
• TM5SDO.R

1. 24 Vdc I/O power segment integrated into the bus bases

DANGER: HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

• Disconnect all power from all equipment including connected devices prior to removing any covers or doors, or installing or removing any accessories, hardware, cables, or wires except under the specific conditions specified in the appropriate hardware guide for this equipment.
• Always use a properly rated voltage sensing device to confirm the power is off where and when indicated.
• Replace and secure all covers, accessories, hardware, cables, and wires and confirm that a proper ground connection exists before applying power to the unit.
• Use only the specified voltage when operating this equipment and any associated products.

Failure to follow these instructions will result in death or serious injury.

DANGER: POTENTIAL FOR EXPLOSION

• Only use this equipment in non-hazardous locations, or in locations that comply with Class I, Division 2, Groups A, B, C and D.
• Do not substitute components which would impair compliance to Class I Division 2.
• Do not connect or disconnect equipment unless power has been removed or the area is known to be non-hazardous.

Failure to follow these instructions will result in death or serious injury.

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.

Use copper conductors only

WARNING: UNINTENDED EQUIPMENT OPERATION

• Use appropriate safety interlocks where personnel and/or equipment hazards exist.
• Install and operate this equipment in an enclosure appropriately rated for its intended environment and secured by a keyed or tooled locking mechanism.
• Use the sensor and actuator power supplies only for supplying power to the sensors or actuators connected to the module.
• Power line and output circuits must be wired and fused in compliance with local and national regulatory requirements for the rated current and voltage of the particular equipment.
  • Do not use this equipment in safety-critical machine functions unless the equipment is otherwise designated as functional safety equipment and conforms to applicable regulations and standards.
• Do not disassemble, repair, or modify this equipment.
• Do not connect any wiring to reserved, unused connections, or to connections designated as No Connection (N.C.).

Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING: POTENTIAL OF OVERHEATING AND FIRE

• Do not connect the equipment directly to line voltage.
• Use only isolating PELV power supplies to supply power to the equipment.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

Legend

1. Internal electronics
2. 24 Vdc I/O power segment integrated into the bus bases
3. 3-wire sensor
4. 2-wire sensor
5. 24 Vdc I/O power segment by external connection
6. External power supply 100…240 Vac
7. External fuse type T slow-blow 1 A 250 V
8. Inductive load protection
9. 2-wire load
10. Vdc I/O power segment by external connection
11. 3-wire load
12. External power supply 24 Vdc
13. External fuse, Type T slow-blow: 8 A max., 250 V
14. External fuse type T slow-blow 5 A 250 V
15. External power supply 110 Vac
16. PS1: External isolated power supply 24 Vdc

Wiring Diagrams

UK Representative

• Schneider Electric Limited
• Stafford Park 5 Telford, TF3 3BL United Kingdom
• www.se.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>