Schneider Electric CCT5015 Wiser Micro Module Blinds and Shutters Instruction Manual

: June 9, 2024
: Schneider Electric

Table of Contents

About this product
1 Choose a suitable location to install
2 Wiring diagram and electrical connections
3 Test puck operation
4 Read full device guide online
Technical data
Trademarks
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**Schneider Electric CCT5015 Wiser Micro Module Blinds and Shutters

**

About this product

The Wiser micro module shades control (hereinafter referred to as puck) is used to control one blind/roller shutter motor equipped with an end position switch.

Note: Do not control any devices that depends on a permanent power supply.
Connect a maximum of 10 mechanical double push buttons to the puck to provide direct operation.

1 Choose a suitable location to install

Choose a suitable location to install

If you place the puck behind a mechanical push button, choose a wall box deep enough to fit both the puck and switch mechanism.

2 Wiring diagram and electrical connections

Wiring diagram and electrical connections

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas:

Connecting to installation networks.
Connecting several electrical devices.
Laying electric cables.
Safety standards, local wiring rules and regulations.
Failure to follow these instructions will result in death or serious injury

DANGER
HAZARD OF ELECTRIC SHOCK

Make sure that the terminal connection area does not come in contact with the metallic parts of any device installed in the same location.
Do not short the outputs to neutral.
The motor contacts and live conductor connection must be separated from one another by a 240 VAC basic insulation.
Failure to follow these instructions will result in death or serious injury.

A Motor contacts (Up/Down)
B Live conductor
C Neutral conductor
D Mechanical push button input 1 (Up)
E Mechanical push button input 2 (Down)

3 Test puck operation

Test puck operation

WARNING
HAZARD OF ELECTRIC SHOCK

Observe the regulations for working on live parts.
Only actuate the device buttons using insulated auxiliary equipment that meets the requirements of EN 60900.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

4 Read full device guide online

Read full device guide online
Scan the QR code and choose your language for complete information about the device, including operation, configuration and pairing the device to a Wiser system.

Technical data

Nominal voltage	AC 220-240 V, 50/60 Hz
Nominal current	4 A, cosq) = 0.6 – 1.0
Blind channel	1, mechanically and electronically locked against each other
Standby	Max. 0.3 W
Operating Temperature	0 °C to 35 °C
Neutral conductor	Required
Connecting terminals	Max. 2 x 2.5 mm2, solid or stranded types
Extension connection	Max. 10 mechanical push buttons
Length of all cable sections	Max. 50 m for 3-wire NYM cable
Fuse protection	16 A circuit breaker
Operating frequency	2405 – 2480 MHz
Max. radio frequency power transmitted	<10 mW
IP rating	IP20
Product dimensions (H x W x D)	43 x 43 x 22 mm
Communication protocol	Zigbee 3.0 certified

Trademarks

Zigbee® is a registered trademark of the Zigbee Alliance.
Wiser™ is a trademark and the property of Schneider Electric SE, its subsidiaries and affiliated companies.
Other brands and registered trademarks are properties of their relevant owners.

EU Declaration of Conformity

Hereby, Schneider Electric Industries, declares that this product is in compliance with the essential requirements and other relevant provisions of RADIO
EQUIPMENT DIRECTIVE 2014/53/EU. Declaration of conformity can be downloaded on: se.com/docs

Schneider Electric Industries SAS
If you have technical questions, please contact the Customer Care Centre in your country.
se.com/contact