MoFi 406FNDMFPD PrecisionDeck Turntable User Guide

MoFi 406FNDMFPD PrecisionDeck Turntable

IN THE BOX

1. Precision Deck Turntable

2. Dustcover

3. Delrin‰ Platter

4. Platter Belt
   

5. RCA Interconnects

6. Power Cord

7. Counterweight

8. Additional Parts

   • Hex Wrench (2)
   • Anti-skate Weight
   • Stylus Brush

ASSEMBLY

• Make sure Precision Deck is placed on a level surface

• If cartridge is not included, follow cartridge manufacturer’s installation instructions
  

• Carefully place the Delrin‰ platter on the bearing hub, making sure it spins freely.

• Install the turntable belt, with the belt attached to the top pulley for 33 RPM records, and the bottom pulley for 45 RPM records.
  

TRACKING FORCE AND ANTI-SKATE

• Install the supplied counterweight on the arm’s ends tub and balance the arm for zero tracking. For best results, use a stylus force gauge (sold separately through your local audio dealer), and set the tracking force as outlined by your cartridge manufacturer’s specifications.

• If your model came with a preinstalled MoFi cartridge, simply install the counterweight until it lines up to the assigned location on the ends tub.
  

• Attach the anti-skate weight with loop to the anti-skate pin, and dress the remaining line and weight to the arm’s anti-skate hanger. Set the loop to the suggested notch on the pin based on your cartridge’s weight. Each notch reads from front to back (refer to chart).

• If Precision Deck came with the Master Tracker™ cartridge preinstalled, use notch 3.
  

VTA AND AZIMUTH

• If Precision Deck came with Master Tracker™ preinstalled, the following steps were completed at the factory”
  

• After setting tracking force and anti-skate, adjust the tonearm’s height. Loosen the hex screw located at the base of the tonearm to raise or lower the arm height, and tighten once the arm is parallel to the record surface.

• Next, adjust your head shell and cartridge for correct azimuth. Loosen the hex screw located under the arm tube, then adjust the head shell as needed until it is parallel to the record surface.
  

CONNECTIONS AND LEVELING

• Install the RCA interconnects and ground wire to your preamp’s phono section, and then connect the power cord from the turntable to any outlet or power conditioner of your choice.
  

• If the turntable is on an unleveled surface, place a bubble level on the platter, then carefully adjust each foot until the turntable’s platter is true.
  

STYLUS CARE AND DUSTCOVER

• Keep your records clean by using a high-quality record brush and record cleaner

• After each play, gently clean your stylus, always brushing back-to-front using the supplied stylus brush. We also recommend using a liquid stylus cleaner such as Mobile Fidelity LP#9.

• When not in use, please cover your turntable with the supplied dustcover. For best sonic results, remove the dustcover while playing.
  

Before changing the fuse, unplug the power cord.
Instructions for Changing the Fuse
Rotate the fuse head counterclockwise with a flat 5mm screwdriver, remove fuse, and change if needed.

TURNTABLE REPACKING GUIDE (v 2)

1. REMOVE THE FOLLOWING ITEMS:

   •  Platter and platter belt
   • Cables
   • Counterweight
   • Anti-skate weight

2. PREPARE FOR SHIPPING

3. Install the cartridge stylus guard and use a small piece of masking tape to hold it in place.

4. Place small foam block underneath the tonearm platform for support.

5. Secure tonearm with supplied foam stabilizer block. Then wrap unit with supplied plastic bag.

6. Place periphery foam strip across the top of the turntable plinth. This should have a snug fit against the foam block supporting the tonearm.

7. PACK THE BOX
   

Documents / Resources

| MoFi 406FNDMFPD PrecisionDeck Turntable [pdf] User Guide
406FNDMFPD PrecisionDeck Turntable, 406FNDMFPD, PrecisionDeck Turntable, Turntable
---|---

References

• MoFi Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>