RYOBI RY18HT55A Cordless 55cm Hedge Trimmer Instruction Manual

RYOBI RY18HT55A Cordless 55cm Hedge Trimmer

Important!

It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Subject to technical modification

For these cordless hedge trimmers, particular attention has been paid to ensuring safety, high performance and reliability.

DESTINY

• The cordless hedge trimmer is only intended for use outdoors, in dry and well-lit areas.
• The product is intended for home use. The product is intended for cutting and trimming hedges, shrubs and similar vegetation.
• Do not use for any other purposes.

GENERAL PRODUCT SAFETY WARNINGS

WARNING! Be sure to read all manuals, illustrations, and specifications provided with this product. Failure to follow the instructions below could result in accidents such as fire, electric shock, and serious injury. Keep these warnings and recommendations for future reference. The term “power tool” in the warnings means a mains-operated (corded) or battery-powered (cordless) product.

WORKING ENVIRONMENT

• The workplace must be kept clean and well lit. Cluttered areas or insufficiently illuminated may be the cause accident.
• Do not run electrical devices in where there is a risk of explosion. for example near flammable liquids, gases or dust. Electrical devices can create sparks that can may be a cause of ignition of the dust or fumes.
• When using power tools, be careful keep bystanders and children away workplaces. Operator distraction can cause loss of control of the device.

SAFETY RULES FOR OPERATION ELECTRICAL APPLIANCES

• Power tool plugs must match to mains sockets. Must not be modified plugs in any way6b. You mustn’t drink no adapters for connecting devices having a grounded power cord. Use of original plugs and matched sockets reduces the risk of electric shock.
• Avoid body contact with grounded surfaces or connected to the neutral pole, e.g. pipes, heating and cooling installations. Body contact with ointment 1 or grounding increases the risk of electric shock.
• Do not expose this product to rain or water. Water getting insideV power tool increases the risk of electric shock.
• Will not damage the power cord. You can’t use the power cord to carry, pulling the device or disconnecting it from the socket network. Keep electrical wires away from sources of heat, oil, sharp edges or moving parts element6w. Damaged or twisted cord electricity increases the risk of electric shock.
• When using the device outdoors, any extension cords must be used for this adapted. Using an extension cord adapted to external conditions decreases risk of electric shock.
• If the use of the device cannot be avoided in wet conditions, they should be replaced supplied from a circuit protected by a circuit breaker residual current device (RCD). The use of such circuit breaker reduces the risk of electric shock electricity.

PERSONAL SAFETY

• Stay focused, watch carefully performed activities, apply the principles of healthy separation when operating the device. I don’t use electrical equipment in a state of fatigue or bQdctc under the influence of drugs, alcohol or substances intoxicants. A moment of inattention during operation power tool can cause serious injury injuries.

• Use personal protective equipment. always on my nose goggles. Protective equipment such as masks anti-dust, protective non-slip shoes, helmet or hearing protection, used when appropriate conditions to prevent injury.

• Avoids the possibility of accidental start-up devices. Before connecting to power battery installation or for its purpose lifting or moving, make sure that that the power switch is in the position disabled. Carrying a power tool with your finger on the switch or connecting the power to the device, in which the circuit breaker is in the on position threatens an accident.

• Remove all tools and wrenches before turning on the power. Starting the power tool with a key placed on a movable element threatens serious accident.

• Don’t go too far. All the time for sure resting your feet and keeping your balance.
  This will give you better control of the device unforeseen situations.

• Wear appropriate protective clothing. Do not wear loose clothing or jewelry. Hair and Keep loose clothing away from moving parts. They may be drawn in by moving parts of the device.

• If your device has a connection to extraction and collecting dust, please use it in the right way6b. Use of dust removal methods reduces the risk associated with its accumulation.

• Do not allow it to be earlier familiarity with the use of similar tools led to ignoring the rules of safety using the tool. Careless handling can cause serious bodily injury in a fraction of a second seconds.

USE

• Do not overload the device. You used the right one tools for the right type of work. the best the effects of work, while maintaining full safety, ensure the use of devices within the parameters rated and in accordance with their intended use.
• Do not use this device if the switch is off I work correctly. Using the power tool without a working circuit breaker is too dangerous – it should be send them in for repair.
• Before making adjustments or replacement of accessories will be before the start disconnect the plug from the storage power source and/or (where possible) disconnect battery from the power tool. This kind preventive measures will reduce the risk accidentally starting the power tool.
• When not in use, devices should be stored outside children’s reach. You must not allow people not to familiar with the operation of electrical devices on them used. Electrical devices may be dangerous in the hands of people without it proper preparation
• Power tools and accessories must be maintained in good technical condition. I should check alignment of moving elements, checking,  whether there are any damages, take into accountall aspects affecting safety device work. In case of finding damaged, return the device for repair. Many accidents are caused by the use of electronic devices unsuitable technical condition.
• Cutting elements must be sharp and clean. Appropriately sharp cutting edges make it easier to guide the machine I They are more resistant to damage.
• All devices, attachments, accessories, etc. should be used in accordance with the accompanying instructions handling, taking into account the conditions and nature work. Using tools in a way inconsistent with their intended use may result in serious injury danger.
• Grips and grips for handcuffs1 always be dry, clean and free of grease and oil. Slippery handles and gripping surfaces do not allow for safe operation and control tools in unexpected situations

USE AND MAINTENANCE

BATTERY TOOLS

• Charge only with a charger supplied by the manufacturer. loader for one model of maze battery be a cause of fire when used for /charging a different type of battery.
• You use power tools only with batteries designed for these manager. The use of other batteries is associated with increased risk of fire or personal injury.
• Store the battery when not in use away from other metal objects, such as paper clips, coins, keys, nails, screws or otherwise small metal objects that might create a connection between the contacts, leading to short circuit. The maze battery contacts are shorted cause burns or fire.
• In case of improper handling, it may occur leakage of battery fluid should be avoided contact with this gas. Possible place rinse with water. In case the gas gets into the eyes, after rinsing ask for help help to the doctor. Liquid leaking from the battery may cause irritation and burns.
• Do not use damaged or modified batteries and tools. damaged or modified batteries may behave in an unpredictable way, which may lead to fire, explosion or risk of injury.
• You do not expose the battery or the tool to the effects fire or too high temperatures. Exposure to exposure to fire or temperatures above 130°C may occur caused an explosion.
• You follow all loading instructions and do not “you charge the battery or tool beyond the specified temperature range in the manual. loading in improperly or outside the specified temperature range may damage the battery and an increase in fire risk.

MAINTENANCE

• The electrical device should be repaired by qualified personnel, using identical spare parts. Thanks to this safety of use will be ensured devices.
• Never service damaged batteries. Batteries should be serviced by • only by the manufacturer or an authorized service

WIRELESS CUTTERS FOR CE SAFETY

• Keep all body parts away from the blade. Do not remove accumulated clippings or hold branches to cut in the hands when the blades are working. The blades continue to rotate after the engine is turned off. Moment inattention when operating the maze hedge trimmer be the cause of serious injury.
• The hedge trimmer must be carried by Rest your hand with the blade stopped, taking care that will not activate any power switch. Carrying the hedge trimmer correctly — reduces risk of unintentional start-up, including the same injuries to the body caused by the blades.
• When transporting or storing the trimmer hedges must always be fitted with a guard sharp. Proper use of the trimmer for hedges reduces the risk of personal injury caused by blades.
• When clearing jammed media or when servicing the device, make sure that all power switches are turned off, a the battery is removed or disconnected. Hedge trimmer starts unexpectedly when clearing jammed media or servicing may cause serious bodily injury.
• The cordless hedge trimmer should only be held by the insulated gripping surface, otherwise the blade may come into contact with hidden wiring. If the blades come into contact with a live wire, exposed metal parts of the hedge trimmer may also become live, possibly resulting in an electric shock.
• Keep all power cords and cables away from the cutting area. Power cords or cables may be hidden in hedges or bushes and may be accidentally cut by the blade.
• Do not use the hedge trimmer in bad weather, especially when there is a risk of being struck by lightning. This reduces the risk of being struck by lightning.

ADDITIONAL SAFETY WARNINGS

• Do not attempt to cut trunks or branches thicker than 26mm for the RY18HTX60A or 24mm for the RY18HT55A, or trunks or branches
  of sizes clearly too large to be inserted into the cutting blade. For cutting larger branches, use a hand saw or pruning saw.

• Always handle the product with both hands firmly holding both handles of the product.

  • Stay firm on the ground when handling the product, unlike any other unstable surface.
  • Inspect the machine before each use. Check that the fasteners are not loose, make sure that all covers and handles are properly and securely fastened. Replace any damaged components before use. Check the battery for leaks6w.
  • Do not turn on the product in poorly lit areas. The operator must have a clear view of the work area to identify potential hazards.

• Check hedges and bushes for hidden objects such as wire fences and hidden wires.

  • The use of hearing protection reduces the audibility of warnings (alarms, shouts). Pay more attention to what is going on in the workplace.

• Turn off the product, remove the battery and allow both the product and the battery to cool down. Make sure that all moving parts have come to a complete stop:

  • before adjusting the working position of the knife
  • before servicing
  • before clearing the blockage
  • before checking, cleaning and using the product,
  • before replacing accessories
  • before leaving the product unattended
  • before starting the inspection for no damage after hitting an object or object
  • before starting maintenance

• Do not force the product into heavily bushy areas. This may cause the knives to melt and slow down their work. As the knives slow down, reduce the feed rate.

• If the product is dropped or hit hard, or if it vibrates abnormally, stop it immediately and inspect for damage or identify the cause of the vibration. Any damaged parts must be properly repaired or replaced by an authorized service center.

• The product should only be used at temperatures between 0°C and 40°C.

• The product should be stored in a place where the ambient temperature is between 0°C and 40°C.

BATTERY – ADDITIONAL SAFETY WARNINGS

• To avoid risk of fire, personal injury or product damage due to a short circuit, do not immerse the tool, removable battery or charger in liquids and ensure that the equipment is no liquids got into the batteries. A short circuit can be caused by corrosive or conductive liquids such as seawater, certain chemicals and bleach or products containing bleach.
• Charge the battery in a place where the ambient temperature is between 10°C and 38°C.
• Store the battery in a place where the ambient temperature is between 0°C and 40°C.
• Use the battery in a place where the ambient temperature is between 0°C and 40°C.

TRANSPORT AND STORAGE

• Remove the battery and allow the product to cool before putting it away, transporting it or storing it.
• Remove any contamination from the product. Store in a well-ventilated room, out of reach of children. For greater safety, store the battery separately from the product. Do not store the appliance with corrosive materials such as garden chemicals or de-icing agents. Do not store the product outdoors.
• When transporting the product, prevent it from moving or falling to prevent personal injury or damage to the product.

TRANSPORTING LITHIUM BATTERIES

Batteries must be transported in accordance with local national laws and regulations.
All special packaging and labeling requirements for batteries must be followed when transported by a third party. Make sure that no batteries come into contact with other batteries or conductive materials during transport; for this purpose, protect exposed connectors with non-conductive insulating caps/caps or insulating tape. Do not transport cracked or leaking batteries. Detailed advice can be obtained from the shipping company.

MAINTENANCE

• Use only original spare parts, manufacturer’s accessories and attachments. In the opposite if not maze dose to the body image, low efficiency
• and to void the warranty. Servicing requires extreme care and knowledge. It may only be carried out by a qualified person service personnel. Servicing should be entrusted authorized service only.
• The blades are very sharp. To avoid body imagery, extreme caution should be exercised cleaning, lubrication and assembly and disassembly
• blade guards. Before adjustment, maintenance or cleaning remove the battery.
• You can perform adjustment and repair activities described in this user manual. For others repair the product should only be returned to
• authorized services. Clean plastic parts after each use
• plastic with a clean, dry cloth. Remove any residue after each use sharpen with a stiff brush, and then before assembling the blade guard, apply carefully anti-rust lubricant. Producer recommends the use of spray lubricant against rust in order to apply evenly layers and to reduce the risk of injury to the body due to contact with the blades. Information about suitable spray product can be obtained
• at your local authorized service center. Check regularly that all nuts, screws and bolts are well tightened to ensure that the product is in safe condition. Any damaged parts should be repaired or replaced as appropriate authorized service center

WITH YOUR PRODUCT

1. Blade
2. Blade guard
3. Front handle
4. Rear handle
5. Start button
6. Blade guard
7. HEDGESWEEP garden sweeper
8. Manual
9. Battery
10. loader

JAMM REMOVAL FUNCTION

The RY18HTX60A hedge trimmers have a function removing jams, allowing the knife to be released if they become jammed in large or hard ones gat. If both knives are jammed activate the Jam Removal function by squeezing the front handle, then press it twice quickly trigger in the rear handle. Our eyes will open and it will be possible resumption of normal operation.

PRODUCT SYMBOLS

• Before starting the device
• please read the instructions carefully.
• Wear ear protection
• Wear eye protection
• Non-slip, durable wear
• protective gloves.
• While the trimmer is in operation, The lifespans should be held with both kami.
• Do not expose the device to the action of rain or use in places with high humidity.
• To prevent serious body injuries, do not touch sharp.
• Before starting work with
• remove the battery from the product.
• Watch out for discarded items.
• All bystanders, especially children and animals, they must be at a distance at least 15 meters above the space work.
• CE This tool meets the requirements all country regulations
• where they were purchased.
• EurAsian Conformance Mark
• Ukrainian Conformity Mark
• Waste electrical products do not
• should be disposed of with waste household. Please give up
• recycled where appropriate
• places. Information about the applicants
• recycling methods can be obtained from local authorities or dealer.
• Guaranteed power level acoustic

SYMBOLS IN THIS MANUAL

• Parts or accessories sold separately
• Explanation
• Warning!

WARNING

The total vibration and noise emission values ​​stated in this instruction manual have been calculated in accordance with a standardized test and can be used to compare different tools. They can be used for a preliminary assessment of exposure.
The specified vibration and noise emission values ​​represent the main application area of ​​the tool. However, if the tool is used in other applications, with other accessories or is poorly maintained, vibrations and noise emissions may differ from those specified. These conditions can significantly affect the exposure levels during the total work period. A scale-up of the exposure level for vibrations and noise should also include in the calculation the times when the tool is switched off or when it is running but not used for work. These conditions can significantly reduce the level of exposure during the total working period.
lidentify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and accessories, keeping the obstacles warm (in dealing with vibrations) and organizing work minutes.

GUARANTEED RYOBI® TERMS & CONDITIONS

In addition to the legal rights arising from the purchase of the product, the warranty mentioned below also applies to the product.

1. The warranty period for consumers is 24 months and starts from the date of purchase of the product. The date must be recorded on the invoice or other proof of purchase. This product is designed and intended for private consumer use only. The warranty therefore does not apply to professional or commercial use of the product.
2. For some garden tools (AC/DC), it is possible to extend the warranty period. This requires registration at www.ryobitools.eu. The possibility of extending the warranty period of the product is clearly indicated in the stores, or on packaging or in product documents. The end user must register his new device online within 30 days from the date of purchase. The end user can register for the extended warranty period in the country of permanent residence, if this is indicated on the internet registration form for the product where this option is available. The end user must further agree to the storage of personal data, which he must enter on the Internet, and accept the terms and conditions. The e-mail confirming the registration and the original invoice with the date of purchase serve as proof of the extended warranty.
3. The warranty applies to all product defects within the warranty period caused by manufacturing defects or material defects at the time of purchase. The warranty is limited to repair or replacement and does not include any other obligations, including, but not limited to, additional or subsequent indemnities. The warranty does not apply if the product is used for inappropriate purposes, in violation of the user manual or if it is connected incorrectly. The warranty does not cover:
4. all damage to the product caused by improper maintenance
5. all products that have been altered or modified
6. all products where the original identification elements (trademark, serial number) have been damaged, altered or removed
7. all damages caused by non-observance of the instructions of the user manual
8. all products without CE certification
9. all products attempted to be repaired by an unqualified repairer or repairer without prior permission from Techtronic Industries.
10. all products connected to a faulty electrical source (current, voltage, frequency)
11. all products used with unsuitable fuel mixture (fuel, oil, percentage of oil)
12. all damages caused by external influences (chemical, physical, impacts) or foreign substances
13. bezne opotfebovanf dflu
14. improperly used, overused tools
15. use of unapproved utilities or dflu
16. all regular cleaning or cleaning as part of carburettor maintenance of components (fly and accessories) subject to wear and tear, including, but not limited to, impact wheels, sliding belts, clutches, blades of hedge trimmers and lawn mowers, straps, gas cable, carbon brushes, power cable, teeth , felt pads, hanging coils, blower fans, blower and vacuum tubes, vacuum cleaner bags and straps, guide sheets, saw blades, hoses, connectors, nozzles, wheels, connecting rods, inner tubes, outer discs, fez strings, spark plugs, air filters, gas filters, mulching knife aid.
17. To perform service, the product must be sent or sent to an authorized RYOBI service center, the addresses of which are listed by country in the list of service centers. In some countries, the seller of the product of this brand sells the product for you after the RYOBI service organization. When sending the product to the RYOBI service center, it is necessary to securely pack the product without dangerous contents such as gasoline, to include the address of the sender and to attach a short description of the defect.
18. Repair,replacement under this warranty is free. It does not mean an extension or start of the warranty period. Replaced dfls or tools become our property. In some countries, a postage fee applies. Your legal rights arising from the purchase of this tool remain unaffected.
19. This warranty is valid in the European Community, Austria, Norway, Liechtenstein, Turkey, Russia and Iceland. If this is the case, contact an authorized RYOBI dealer to find out if the product is covered by another warranty.

AUTHORIZED SERVICE CENTER

If you have any questions or problems regarding this product, please contact our authorized service center (according to www.ryobitools.eu) or by mail to: Techtronic Industries GmbH, Max Eyth StraBe 10, 71364 Winnenden, Germany. Enter the manufacturer’s code and the type of product from the label.

COMPLIANCE INQUIRY Cordless hedge trimmer1

Brand : RYOBI

We declare on our own responsibility that the product described below meets all of them relevant provisions of the European directives, European regulations and harmonized standards

RY18HTX60A

• Painted sound effect level ………………………………………… …. 93.6 dB(A)
• Guaranteed sound power level ………………………………………. 96 dB (A)

RY18HT55A

• Painted sound effect level ………………………………………… …. 93.7 dB(A)
• Guaranteed sound power level ………………………………………. 96 dB (A)

Method for assessment of conformity Iii Appendix V Directive 2000/14/EC amended by 2005/88/EC.
Authorized to compile the technical file: 3

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>