DAP WMS6T-W Passive Design Wall Speaker User Manual

: June 9, 2024
: DAP

DAP WMS6T-W Passive Design Wall Speaker

Preface

Thank you for purchasing this DAP product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
This user manual contains information concerning:

Safety instructions
Installation and operation of the device
Intended and non-intended use of the device
Maintenance procedures
Troubleshooting
Transport, storage and disposal of the device

Non-observance of the instructions in this user manual may result in serious injuries and damage of property.

Introduction

Before Using the Product

Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer.

Your shipment includes:

DAP WMS6T-W
Mounting plate
Mounting screw
Rubber gasket
User manual

Introduction

Intended Use

This device is designed to be used as a 100 V line wall-mount speaker. The device is suitable for fixed permanent installation in commercial and public spaces. It can be installed indoors and outdoors. Any incorrect use may lead to hazardous situations and result in injuries and material damage.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Text Conventions

Throughout the user manual the following text conventions are used:

References: References to chapters and parts of the device are in bold lettering, for example: “Refer to 2. Safety”, “press the power switch (03)”
0–255: Defines a range of values
Notes: Note: (in bold lettering) is followed by useful information or tips

Symbols and Signal Words

Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.

DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING Indicates an imminently hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

Attention Indicates important information for the correct operation and use of the product.

Important Read and observe the instructions in this document.

Provides important information about the disposal of this product.

Symbols on the Information Label

This product is provided with an information label. The information label is located on the bottom plate of the device.
The information label contains the following symbols:

This device shall not be treated as household waste.

Read and follow the instructions in the user manual before installing, operating or servicing the device.

Safety

Important Read and follow the instructions in this user manual before installing, operating or servicing this product.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.

Warnings and Safety Instructions

DANGER Danger for children

For adult use only. The device must be installed beyond the reach of children.

Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within children’s reach. Packaging material is a potential source of danger for children.

Attention Speaker load

Make sure that the total wattage of all connected speakers does not exceed the rated wattage of the amplifier.
Make sure that the speaker cable run is appropriate for the total speaker load.

Attention General safety

Do not shake the device. Avoid brute force when installing or operating the device.
If the device fails to work properly, discontinue the use immediately

Attention This device shall be used only for the purposes it is designed for.

This device is designed to be used as a 100 V line wall-mount speaker. Any incorrect use may lead to hazardous situations and result in injuries and material damage.

This device is not suitable for households.
This device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.

Attention Do not expose the device to conditions that exceed the rated IP class conditions.

This device is IP54 rated. IP (Ingress Protection) 54 class means that the device is dust-protected. Ingress of dust does not interfere with satisfactory operation of the device. Water splashed against the enclosure from any direction shall have no harmful effect.

Requirements for the User

This product may be used by ordinary persons. Maintenance may be carried out by ordinary persons.
Service and installation shall be carried out only by instructed or skilled persons. Contact your Highlite International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person, for specific tasks and work activities associated with the installation, service and maintenance of this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the product but also any other persons that may have access to the device or who may be in the vicinity of the device.

Description of the Device

The DAP WMS6T-W is an IP-rated 100 V speaker for low-impedance audio installations. The device can be easily mounted to a wall, in a horizontal or vertical orientation. The DAP logo on the front is rotatable. The device can be used in shops, restaurants or clubs, as well as in sheltered outdoor locations.

Front View

Speaker grill
Rotatable logo
Rubber ball-joint cover

**Fig. 02**

Back View

Mounting panel
4 x speaker mounting holes
Speaker connector
Mounting plate (See 3.4. Mounting Plate on page 8)
Rubber gasket
Line transformer tap cover
Line transformer tap selector

**Fig. 03**

Bottom View

Mounting screw (M3 x 10 mm)
2 x adjustment screws (M6 x 45 mm)
Ball-joint

**Fig. 04**

Mounting Plate

4 x mounting holes (Ø 5 mm)
4 x mounting hooks
4-pin terminal connector

**Fig. 05**

Product Specifications

Model:	DAP WMS6T-W

Dimensions

Installation and Setup

Safety Instructions for Installation

WARNING
Incorrect installation can cause serious injuries and damage of property.

Installation Site Requirements

The device can be used outdoors.
The device can be mounted on a wall in a vertical or horizontal orientation.
The device must be installed away from heating sources.
The maximum ambient temperature ta = 45 °C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 45 °C

Mounting and Setup

To mount the device, you need:

Phillips screwdriver (PH1)
Hex key (5 mm)
Anchors
Drill bits
Power drill

To mount and set up the device, follow the steps below:

Drill mounting holes on the wall. See 4.3.1. Drilling Mounting Holes on page 12.
Connect the amplifier and daisy-chain the WMS speakers. See 4.3.2. Connecting Devices on page 13.
Install the mounting plate (07) on the wall. See 4.3.3. Installing the Mounting Plate on page 15.
Set a correct line transformer tap. See 4.3.4. Setting Line Transformer Taps on page 16.
Install the speaker on the mounting plate (07). See 4.3.5. Installing the Speaker on page 17.
Adjust the angle of the device. See 4.3.6. Adjusting the Angle on page 18.
Adjust the orientation of the logo. See 4.3.7. Adjusting the Logo on page 19.
Connect the amplifier to the power supply. See 4.3.8. Connecting the Amplifier on page 20.
Switch on the amplifier.

Drilling Mounting Holes

Hold the mounting plate (07) against the wall, as shown in Fig. 07, and mark the mounting locations.

Installation and Setup

Drill holes at the marked locations. See 4.3.1.1. Drilling into Wood or 4.3.1.2. Drilling into Concrete on page 12 for more information.
Insert anchors into the drilled holes (Fig. 08). Do not perform this step when mounting the device on a wooden wall.

**Fig. 08**

Drilling into Wood

If you drill into wood, use hardwood drill bits. Predrill before inserting screws, to remove drill dust and to avoid damaging of the wood.

Installation and Setup
**Fig. 09**

Note: Drill bits shall be of the same diameter as the anchors.

Connecting Devices

Connect all cables to the mounting plate (07). Make sure that the cable polarity is correct (+/-) (Fig. 11).

Installation and Setup

**Fig. 11**

100 V Amplifier Mode

To use the device with a 100 V amplifier, follow the steps below:

Connect the COM output of the 70/100 V amplifier to one of the (-) connectors on the mounting plate (07).
Connect the line transformer tap (70 V or 100 V) of the 70/100 V amplifier to one of the (+) connectors on the mounting plate (07).
Connect multiple speakers as shown in Fig. 12.

WMS6T-W

Conventional Amplifier Mode

To use the device with a conventional amplifier, follow the steps below:

Connect the (-) output of the conventional amplifier to one of the (-) connectors on the mounting plate (07) of the first speaker.
Connect the (+) output of the conventional amplifier to one of the (+) connectors on the mounting plate (07) of the first speaker.
Connect multiple speakers as shown in Fig. 13.

Installing the Mounting Plate
Install the mounting plate (07) with the mounting hooks facing up (Fig. 14).

Fig.14

To install the mounting plate (07), follow the steps below:

Hold the mounting plate (07), with the rubber gasket (08), against the wall, in such a way that all cables fit through the opening in the rubber gasket (08) (Fig. 15)
Note:
Make sure that the opening in the gasket is located at the bottom (Fig. 15). If, for any reason, such installation is not possible, seal the opening with a waterproof sealant to protect the device from the ingress of water (Fig. 16).
Insert and tighten the screws to install the mounting plate (07) and the rubber gasket (08) on the wall (Fig. 17). The screws shall be at least 12,5 mm long. Do not overtighten the screws as this can damage the mounting plate (07). The damaged mounting plate (07) cannot support the weight of the device and can break easily.

Setting Line Transformer Taps
The device has multiple selectable line transformer taps.
To select line transformer taps, follow the steps below:

Pry up and remove the line transformer tap cover (09) to get access to the line transformer tap selector (10).
1Turn the line transformer tap selector (10) to select a line transformer tap. The available line transformer taps are:
Install the line transformer tap cover (09) again.

Note:
The line transformer tap values depend on the type of amplifier connected to the PA system.

For a 70 V amplifier, the line transformer taps are: 2,5 W/3,5 W/7,5 W/15 W.
For a 100 V amplifier, the line transformer taps are: 5 W/7,5 W/15 W/30 W.
For a conventional amplifier, use only the “8 Ω” line transformer tap.
The higher the wattage setting, the higher the volume level of the speaker

Installing the Speaker

Turn the mounting screw (11) counter-clockwise to remove it.
Hang the speaker on the mounting plate (07) (Fig. 19).
Notes:
● The 4 x mounting hooks (15) shall fit through the 4 x speaker mounting holes (05) on the mounting panel (04).
● The speaker connector (06) shall fit in the 4-pin terminal connector (16) on the mounting plate (07).
Insert the mounting screw (11) and tighten it with the Phillips screwdriver (Fig. 20).

Adjusting the Angle

You can adjust the angle of the device with the adjustment screws (12).
To adjust the angle, follow the steps below:

Fold the rubber ball-joint cover (03) to get access to the adjustment screws (12).
Loosen the adjustment screws (12) with the hex key (Fig. 21).
Tilt the device. The tilt range is 30° in all directions (Fig. 22).
Rotate the ball-joint (13) to set the device in a vertical or horizontal orientation (Fig. 23). The ball-joint rotation range is 90°.
Tighten the adjustment screws (12) with the hex key, so that the device cannot move freely.
Unfold the rubber ball-joint cover (03).

Adjusting the Logo
You can adjust the orientation of the DAP logo on the speaker grill so that it is always legible, regardless of the orientation of the device.

Option 1

Use a tool to pry up the rotatable logo (02).
Move the rotatable logo (02) to the correct orientation.

Option 2

Pry up the speaker grill (01) and remove it from the device (Fig. 25).
On the inside of the speaker grill (01), press on the spring-loaded pin and move the rotatable logo
to the correct orientation (Fig. 26).
Release the spring-loaded pin.
Install the speaker grill (01) on the device.

Connecting the Amplifier

**** Attention Speaker load

Before connecting the amplifier to the power supply, make sure that the total load of all connected speakers is below the maximum rating of the amplifier. If the total load is higher, it may cause damage to the amplifier and to the speakers.
The total load depends also on the current line transformer tap setting of the speakers. See Setting
Line Transformer Taps on page 16 for more information. To determine if the settings are correct:

Add up the wattage settings of all connected speakers.
Compare the value with the maximum rating of the amplifier. If necessary, disconnect speaker(s).

Troubleshooting

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts.
Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.
Refer servicing to instructed or skilled persons. Contact your Highlight International dealer in case the solution is not described in the table.

Problem	Probable cause(s)	Solution
The device does not function at all	Bad connection

Check if the connections between the devices are correct

No power to the amplifier|

Check if the amplifier is on

Incorrect settings|

Check if correct line transformer taps are selected Check if the amplifier is compatible with the device

No sound| Incorrect polarity of the connections|

Check if the polarity of the connections between the devices is correct

Maintenance

Preventive Maintenance

Attention
Before use, examine the device visually for any defects.

Make sure that:

There are no deformations on the housing
The device is rigidly mounted to the wall.

Basic Cleaning Instructions

To clean the device, follow the steps below:
Clean the device with a soft, lint-free cloth.

Attention

Do not immerse the device in liquid.
Do not use alcohol or solvent

Corrective Maintenance

The device does not contain user-serviceable parts. Do not open the device and do not modify the device.
Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for more information.

Deinstallation, Transportation and Storage

Instructions for Deinstallation

WARNING
Incorrect deinstallation can cause serious injuries and damage of property.

Disconnect power supply before deinstallation.
Always observe the national and site-specific regulations during deinstallation and derigging of the device.
Wear personal protective equipment in compliance with the national and site-specific regulations.

+Instructions for Transportation

Use the original packaging to transport the device, if possible.
Always observe the handling instructions printed on the outer carton box, for example: “Handle with care”, “This side up”, “Fragile”.

Storage

Clean the device before storing. Follow the cleaning instructions in chapter 6.1.1. Basic Cleaning Instructions on page 21.
Store the device in the original packaging, if possible

Disposal

Correct disposal of this product
Waste Electrical and Electronic Equipment
This symbol on the product, its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. For more detailed information about recycling of this product contact the local authorities or the authorized dealer.

Approval

Symbols Check the respective product page on the website of Highlite International (www.highlite.com) for an available declaration of conformity.

Product code: D3843

Documents / Resources

| DAP WMS6T-W Passive Design Wall Speaker [pdf] User Manual
WMS6T-W Passive Design Wall Speaker, WMS6T-W, Passive Design Wall Speaker, Design Wall Speaker, Wall Speaker, Speaker
---|---