LD SYSTEMS LDMAUI44G2 Cardioid Powered Column Loudspeaker User Manual

LD SYSTEMS LDMAUI44G2 Cardioid Powered Column Loudspeaker

YOU‘VE MADE THE RIGHT CHOICE!
We have designed this product to operate reliably over many years. LD Systems stands for this with its name and many years of experience as a manufacturer of high-quality audio products. Please read this User‘s Manual carefully, so that you can begin making optimum use of your LD Systems product quickly.
You can find more information about LD-SYSTEMS at our Internet site WWW.LD- SYSTEMS.COM

SAFETY INFORMATION

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observe the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment
   is always installed so that is cooled sufficiently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. Keep a minimum distance of 20 cm around and above the device.

12. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment – in this case, observe the special instructions noted below. Do not expose this equipment to flammable materials, fluids or gases. Avoid direct sunlight!

13. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with liquids, such as vases or drinking vessels, on the equipment.

14. Make certain that objects cannot fall into the device.

15. Use this equipment only with the accessories recommended and intended by the manufacturer.

16. Do not open or modify this equipment.

17. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.

18. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.

19. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.

20. Clean the equipment using a dry cloth.

21. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.

22. Plastic bags must be kept out of reach of children.

23. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
    FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS

24. CAUTION : If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

25. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.

26. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

27. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power adapter and the equipment connector.

28. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.

29. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the equipment.

30. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorised service centre.

31. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.

32. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables.

33. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

34. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

35. Children must be instructed not to play with the device.

36. If the power cord of the device is damaged, do not use the device. The power cord must be replaced by an adequate cable or assembly from an authorized service center.

CAUTION:

• To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts inside. Maintenance and repairs should be exclusively carried out by qualified service personnel.
• The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an electrical shock.
• The warning triangle with exclamation mark indicates important operating and maintenance instructions.
• Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait for a cool-down period of at least 10 minutes before handling or transporting the device.
• Warning! This device is designed for use below 2000 metres in altitude.
• Warning! This product is not intended for use in tropical climates.

CAUTION! HIGH VOLUMES IN AUDIO PRODUCTS!

This device is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national ac-cident prevention rules and regulations. As a manufacturer, Adam Hall is obligated to notify you formally about the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels (SPL) that can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid prolonged exposure to volumes in excess of 90 dB.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

INTRODUCTION

The LD Systems MAUI 44 G2 column PA system has been designed for professional use. The PA system provides high-quality components, DSP-con-trolled amplifiers and a balanced sound across the entire frequency spectrum. The digital signal processing of the LD LECC DSP includes functions such as crossover, EQ, compressor and limiter, and has been tailored to the MAUI 44 G2 PA system to ensure optimum audio performance at all times.
The system has been designed as a plug and play system. It comes without any additional cables or stands and can therefore be assembled and disassembled quickly and easily.

FEATURES

• Professional column PA system with 1500 W RMS and 132 dB max. SPL
• Cardioid column for controlled low- and mid-range frequency dispersion and cardioid subwoofer application (with additional subwoofer)
• TrueWirelessâ„¢ stereo technology for wireless stereo pairing of two column systems
• aptXâ„¢ coding and advanced audio coding (AAC) for high-resolution Bluetooth® streaming
• BEM-optimized high-frequency waveguide for uniform dispersion pattern, phase plug for coherent mid-range wavefront and flow-optimised bass-reflex ports
• DynX® DSP technology for distortion-free sound at maximum volume
• Automatic setup detection
• Fast and simple assembly without stands or cables
• Rugged subwoofer housing made out of polyurea-coated birch plywood and lightweight, powder-coated aluminium column

PLEASE NOTE: The optional subwoofer extension LDMAUI44G2SUB is technically identical to the subwoofer from the LDMAUI44G2 PA system. The subwoofer extension LDMAUI44G2SUB is supplied with a cover for the connection panel for the column speakers.

ASSEMBLY, CONNECTION AND OPERATION

GENERAL INFORMATION

Both the subwoofer of the LD Systems MAUI 44 G2 PA system and the optional subwoofer exten-sion MAUI 44 G2 SUB must be positioned on a flat surface on their rubber feet before use. Never operate the system on a trolley as there is a risk that the entire system may begin to move in an uncontrolled manner. This may result in accidents and damage. The amplifier is cooled via the heat sink below the connection panel on the back of the subwoofer. To ensure sufficient cooling during operation, a minimum distance of 50 cm must be maintained between the back of the subwoofer and other similar objects such as walls.
Please ensure that the system as well as any connected devices such as mixing consoles, CD play-ers etc. are connected to the correct audio and power connections. Use only undamaged cables with a suitable diameter and always unroll cable reels fully. Use cable protectors to avoid tripping accidents caused by loose cables. Never position the device directly on an edge. Do not place the subwoofer on a table. In order to eliminate unwanted noise when turning on connected devices, always switch the system on last and switch it off first.

ASSEMBLY

The LD Systems MAUI 44 G2 PA system comprises three components:

1. A Subwoofer with integrated electronics for all system components.

2. B MAUI 44 G2 LC:
   Lower vertical array column with six 3.5″ speakers, each with a multipin connector on the top and bottom and a guide pin on the underside.

3. C MAUI 44 G2 U:

4. The upper vertical array column with six 3.5” loudspeakers with phase plug, tweeters and a multi-pin connector and guide pins on the bottom side.
   After the subwoofer has been placed in the desired position, the lower array column is attached to the subwoofer. Rugged guide pins help the multipin connectors on each speaker to interlock perfectly. One strong magnet provide extra stability. The upper vertical array column is then attached to the lower column in the same way.
   To simplify transport, set-up and dismantling, two ergonomic handles are located on the sides of the subwoofer and an optionally available castor board (LDM44G2CB) can be installed on the back that also provides protection for the connection panel and controls during transport. Recessed handles are located on the top and underside of the array columns.
   The optional MAUI 44 G2 SUB subwoofer extension is positioned next to the MAUI 44 G2 PA system. The orientation of the subwoofer extension depends on whether the cardioid preset in the subwoofer extension is used or not.

CONNECTION AND OPERATION

A playback device can be connected via the balanced XLR inputs. The integrated Bluetooth module enables wireless control via smartphone or tab-let. There is also a stereo link function for wireless transmission of the Bluetooth signal to another MAUI 44 G2 PA system as a stereo extension. Both the volume of the entire system as well as the volume of subwoofer relative to the overall volume can be adjusted on the device. An optionally available subwoofer extension can be used in two different setups together with the MAUI 44 G2 PA system.

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

1. IN
   Balanced line stereo input with two 3-pin female XLR sockets for connection of a playback device (e.g. mixer). Any stereo signal present is internally summed to mono.

2. MAIN
   Level control for overall volume. The subwoofer volume level is controlled by adjusting the SUB level control accordingly. When the subwoofer is used as subwoofer extension, the level control is disabled and the MAIN display field is turned off.

3. SUB
   Setting the volume balance between the subwoofer and the column speaker. When the subwoofer is used as subwoofer extension, the level control is deactivated and the SUB display field is turned off.

4. SYSTEM STATUS DISPLAY

5. PROTECT – The display field lights up if the system is overloaded/overheating. The amplifiers are then muted automatically. After reaching normal
   operating conditions, the unit returns to the normal operating mode after a few minutes.

6. LIMIT – The display field lights up if the speaker system is being operated in its upper limit range. Brief illumination of the LED is not critical. To protect the system, any excessive signal level is lowered smoothly by the integrated limiter. If the limiter LED remains lit for longer or permanently, reduce the volume level.

7. SIGNAL – The display field lights up when the device is receiving an audio signal. The signal is received before the MAIN level control.

8. POWER – The display field lights up when the device is properly connected to the mains and switched on.

9. SLAVE – The display field lights up when the columns are detached from the system and the subwoofer can be used as a subwoofer extension.

10. THRU
    Balanced stereo line output with two male 3-pin XLR sockets for sending the input signal.

11. SUB OUT
    Balanced line output with male 3-pin XLR socket for control of the subwoofer extension. Subwoofer extension: Use either line input L or R for signal control. Both MAIN and SUB level controls and the Bluetooth unit with TWS are disabled if the MAUI 44 G2 subwoofer is used as a subwoofer extension. A description of the cardioid set-up can be found under point 9 CARDIOID ON/OFF.

12. HOLD TO LINK

13. The MAUI 44 G2 PA system is equipped with Bluetooth, which means that audio files from a Bluetooth playback device (e.g. smartphone or tablet)can be played back on the MAUI 44 G2 PA (maximum distance between the two devices depends on the surroundings).

14. To pair and connect the internal Bluetooth unit with a Bluetooth playback device, press and hold the HOLD TO LINK button for approximately 3 seconds until the Bluetooth display field above the button flashes rhythmically (approx. 3 Hz). Enable Bluetooth on your playback device and search on the user interface for available devices. Select “MAUI 44 G2” and pair your Bluetooth device with the Bluetooth unit of the MAUI 44 G2 PA system. If successfully paired, the Bluetooth symbol will light up permanently and playback can be started. The volume is controlled via the MAIN level control or on the playback device.

15. To disconnect a Bluetooth device and set the Bluetooth unit back to standby, press and hold the HOLD TO LINK button again for approximately 3 seconds. To delete the entire list of paired devices (= factory default), press and hold the HOLD TO LINK and STEREO LINK buttons simultaneously for
    approximately 2 seconds.

16. If the Bluetooth connection is interrupted (e.g. range is exceeded), the Bluetooth LED will go out. Connection can be restored automatically within
    approx. 90 seconds (Bluetooth device back in range). After 90 seconds, the connection can be restored with the Bluetooth playback device (connect
    paired device).

17. When using a single MAUI 44 G2 PA system, any stereo signal is automatically summed to mono in the Bluetooth module.
    Note: The Bluetooth and TWS functions are not available if the subwoofer is used as a subwoofer extension for an existing MAUI 44 G2 PA system.

18. STEREO LINK / TWS

19. The MAUI 44 G2 PA system is equipped with a Bluetooth stereo link function (true wireless stereo), which means that if two MAUI 44 G2 systems are used, stereo audio signals transmitted via Bluetooth can also be played back in stereo without a cable connection between the two systems (the maximum distance between the two devices is 40 metres under optimal conditions). The system that is connected to the Bluetooth playback device is hereinafter referred to as the master unit, the stereo expansion as a slave unit. If the master unit with the Bluetooth playback device is connected to the slave unit, the Bluetooth display field and the TWS display field on the master unit light up permanently. If connection is successfully established between the slave unit and the master unit, the TWS display field on the slave unit lights up permanently and the Bluetooth display field flashes slowly (approximately 0.3 Hz). During the pairing process, the TWS display fields on both systems flash rhythmically at a frequency of about 3 Hz.

20. Depending on the situation, there are two different methods to pair two MAUI 44 G2 PA systems via TWS: Situation A. Stereo system with 2 x MAUI 44 G2 and 1x Bluetooth playback device: Pair a Bluetooth playback device with the left MAUI 44 G2 system.

21. The left-hand system automatically becomes the master unit. Disconnect all existing Bluetooth connections on the right-hand MAUI 44 G2 (press and hold HOLD TO LINK and STEREO LINK simultaneously for approximately 2 seconds). Now pair the right MAUI 44 G2 system with the master unit by pressing and holding the STEREO LINK button on both devices for approximately 3 seconds within 30 seconds. The right-hand system automatically becomes the slave unit (max. distance when pairing 15 m). The master unit transmits the left channel of the stereo signal from the Bluetooth device and the slave unit the right channel.

22. Situation B. Stereo system with 2 x MAUI 44 G2, pair Bluetooth playback device later: Disconnect all existing Bluetooth connections on the slave unit by simultaneously pressing and holding the HOLD TO LINK and STEREO LINK buttons on the slave unit for approximately 2 seconds. When pairing two MAUI 44 G2 systems, ensure that the distance between the systems is no more than 15 metres. Press and hold the STEREO LINK button on the master unit for approximately 3 seconds and press the STEREO LINK button twice in quick succession on the slave unit. Pairing occurs place automatically within approximately 30 seconds. Pairing a Bluetooth playback device with the master unit can now be done later. The master unit transmits the left channel of the stereo signal from a Bluetooth playback device and the slave unit the right channel.

PLEASE NOTE:

• Only audio signals from a paired Bluetooth playback device can be transmitted via the TWS stereo link function. Audio signals at the line input will not be transmitted via TWS.
• When the MAUI 44 G2 systems have been switched off and back on, the Bluetooth playback device will pair automatically and the systems will connect with each other automatically via TWS.
• The maximum number of paired Bluetooth devices is 8 (including paired MAUI 44 G2 systems). If another device is paired, the last entry from the list of stored devices will be deleted. A maximum of one Bluetooth playback device and one MAUI 44 G2 system can be connected simultaneously with the MAUI 44 G2 master unit to create a stereo extension.

Bluetooth and TWS status

Bluetooth and stereo link status| Bluetooth LED| STEREO LINK LED
---|---|---
Pair Bluetooth unit with playback device| Flashes (3 Hz)| off
Bluetooth unit is paired and connected only with playback device| on permanently| off
Pair Bluetooth unit with playback device (as stereo link – master)| Flashes (3 Hz)| on permanently
Pair slave unit – stereo link to master unit| Flashes (0,3 Hz)| Flashes (3 Hz)
Slave unit – stereo link paired with master unit| Flashes (0.3 Hz)| on permanently
Slave unit – slave unit paired but not connected| Flashes (0.3 Hz)| off
Pair master unit – stereo link pairing without Bluetooth connection to playback device| off| Flashes (3 Hz)
Master unit connected to slave unit but without Bluetooth connection to playback device| off| on permanently
Master unit – stereo link pairing with Bluetooth connection to playback device| on permanently| Flashes (3 Hz)
Master unit connected to slave unit with Bluetooth connection to playback device| on permanently| on permanently
Neither Bluetooth nor stereo link connection| off| off

CARDIOID SUBWOOFER ON / OFF
Note : The cardioid subwoofer feature is only available when the loudspeaker columns are not connected to the MAUI 44 G2 subwoofer. MAIN / SLAVE operation: The optionally available MAUI 44 G2 SUB subwoofer extension can be used with the MAUI 44 G2 PA system in two different ways.
The subwoofer extension is positioned in the same orientation as the subwoofer of the MAUI 44 G2 PA system. In this case, the cardioid preset on the subwoofer extension must be disabled (CARDIOID OFF). Press and hold the CARDIOID button for about 2 seconds to change status.
The subwoofer extension is positioned 180° to the subwoofer of the MAUI 44 G2 PA system. In this case, the cardioid preset must be enabled (CARDIOID ON). Press and hold the CARDIOID button for about 2 s econds to change status. The cardioid set up results in more pr ominent bass dispersion at the front and a clearer stage sound at the rear due to extensive low-frequency cancellation.

POWER INPUT
Neutrik powerCON mains input socket. A suitable power cable is included.
POWER
On–off switch for power supply to the device. Safe disconnection from the power supply is achieved only by pulling the mains plug

WIRING EXAMPLES

Example of mono operation

Example of stereo operation

Subwoofer extension (cardioid setup):

OPTIONAL ACCESSORIES

• LDMAUI44G2SUB
  Subwoofer extension

• LDM44G2CB
  Castor board for subwoofer

• LDM44G2SUBPC
  Cover for subwoofer

• LDM44G2SATBAG
  Transport bag for columns

TECHNICAL DATA

MANUFACTURER´S DECLARATIONS

MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY
You can find our current warranty conditions and limitations of liability at:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS-LD- SYSTEMS.pdf To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Anspach / Email: Info@adamhall.com / +49 (0)6081 / 9419-0.
CORRECT DISPOSAL OF THIS PRODUCT

(valid in the European Union and other European countries with a differentiated waste collection system) This symbol on the product, or on its documents indicates that the device may not be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased this product, or their local government office, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste for disposal.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation

SIMPLIFIED UK DECLARATION OF CONFORMITY

Hereby, Adam Hall Ltd. declares that the radio equipment type ( Radio Equipment Regulations 2017) is in compliance with
Directive SI2017/1206. The full text of the UK declaration of conformity is available at the following internet adress: www.adamhall.com/compliance/

CE Compliance

Adam Hall GmbH states that this product meets the following guidelines (where applicable):
R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017
Low voltage directive (2014/35/EU)
EMV directive (2014/30/EU)
RoHS (2011/65/EU)
The complete declaration of conformity can be found at www.adamhall.com.
Furthermore, you may also direct your enquiry to info@adamhall.com.

EU DECLARATION OF CONFORMITY
Hereby, Adam Hall GmbH declares that this radio equipment type is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.adamhall.com/compliance/

Adam Hall GmbH
Adam-Hall-Str. 1
61267 Neu-Anspach
Germany Phone: +49 6081 9419-0
adamhall.com

References

• Eventtechnik Lösungen | Adam Hall Group
• LD Systems® | Your Sound. Our Mission.
• Eventtechnik Lösungen | Adam Hall Group
• Downloads | Service | Adam Hall Shop
• LD Systems® | Your Sound. Our Mission.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>