HINKLEY 19675 Open Air Maddox LED 24 inch Black Outdoor Pendant Instruction Manual

HINKLEY 19675 Open Air Maddox LED 24 inch Black Outdoor Pendant

Assembly Instructions

start here

1. Find a clear area in which you can work.

2. Unpack fixture and glass from carton.

3. Carefully review instructions prior to assembly.

4.  To begin installation it will be necessary to determine the desired height the pendant will be installed.

5. The fixture is supplied with assorted stem sizes. Determine what combinations of stems are needed to achieve desired length see Drawing 1.

6. Slip stems over wire and thread first stem onto top of pendant, longest stem first. Repeat this process until all required stems are threaded together.

7. In the following order: take retainer ring (|) and canopy (G) and slide them over the stems attached previously.

8. Slip wire through center hole of swivel with flat plate (A), slip swivel and plate along wire, and thread into the top of the last stem installed.

9. Attach universal mounting strap (B) to the junction box (J) with screws (C) not provided- see Drawing 2.

10. Slip holes (E) in mounting plate with swivel (A) over screws (D) in mounting strap (B).

11. Thread ball knobs (F) onto screws (D) to secure fixture to universal strap (B).

12. All necessary wiring can be done at this time. Please follow I.S. 18 for wiring instructions.

13. Slip canopy (G) up along rods (R) and over mounting plate with swivel (A).

14. Slip retaining ring (1) up to canopy and thread onto coupler (K), located on the mounting plate and sWivel assembly, to secure parts.

15. After stems (M) are assembled slip cover (N) over stems

16. Use set screw to lock to cover into place

17. Secure shade (V) to top cover (N)

18. Bulb fixture using an appropriate medium base bulb

19. Next hold glass (1) up and use the three knobs (3) lock into place -Drawing 4

20. Use allen key to secure the set screw (S). This will lock to cover into place

21. Fixture power can now be restored

start here

1. Find a clear area in which you can work.

2. Unpack fixture and glass from carton.

3. Carefully review instructions prior to assembly.

4. After stems (M) are assembled slip cover (N) over stems

5. Use set screw to lock to cover into place

6. Secure shade (V) to top cover (N)

7. Bulb fixture using appropriate medium base bulb

8. Next hold glass (1) up and use the three knobs (3) lock into place -Drawing 4

9. Use allen key to secure set screw (S). This will lock to cover into place

10. Fixture power can now be restored

I.S. 18 wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS.
TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth,unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2 .
2. Connect negative supply wire ( C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead ( D).
3.  Please refer to the g rounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire ( A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead ( B) with appropriately sized twist on connector — – see Drawings 2 o r 3.

2. Connect negative supply wire ( C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead ( D).

3. Cover open end of connectors with silicone sealant to form a watertight seal.
   If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.

4. Please refer to the g rounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1 .

Note: On straps for screw supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground w ire of the building system with appropriately sized twist-on connectors – see Drawing 2.

Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3

HINKLEY 33000 Pin Oak Parkway,Avon Lake,OH44012800.446.5539/440.653.5500 hinkley.com

References

• HINKLEY - Lighting and Ceiling Fans

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>