MOORE RACE CHASSIS FABRICATION MRC8100N MRC Foxbody Pre-Notched 8.50 Cage Kit User Manual

June 9, 2024
MOORE RACE CHASSIS FABRICATION

MOORE-RACE-CHASSIS -LOGO

MOORE RACE CHASSIS   FABRICATION MRC8100N MRC Foxbody Pre-Notched 8.50

Cage Kit

MOORE-RACE-CHASSIS -FABRICATION-MRC8100N-MRC-Foxbody-Pre-Notched-8-50-Cage-
Kit-PRODUCT

MRC Foxbody Pre-Notched 8.50 Cage Kit
Thank you for choosing MRC for your cage kit!
We hope we made this as painless as possible.
If there are any questions this sheet doesn’t cover, please contact us by phone, Email or Facebook Messenger.
Phone – (636) 791 1541
Email –  info@Mooreracechassis.com
You have 48 Hours to inventory tubing and report missing tubing upon receiving pallet. After 48 hours we are not responsible for missing tubing.

PARTS DESCRIPTIONS

MOORE-RACE-CHASSIS -FABRICATION-MRC8100N-MRC-Foxbody-Pre-Notched-8-50-Cage-
Kit-FIG 1. MOORE-RACE-CHASSIS -FABRICATION-MRC8100N-MRC-Foxbody-Pre-Notched-8-50-Cage-
Kit-FIG 2

INSTALLATION

These Lengths are based on a plain tube. Lengths will be shorter if it is notched.

This kit allows you to install a 8.50 Cage kit with relative ease. Without spending a lot of money on a notcher and required tools.
Due to the nature of each individual car some adjustment is required to fit perfectly for your vehicle.
To do this, we recommend a sanding drum/roll. Pictured below.
We have these on our website if you do not have one of your own.

This guide is to be a supplement to common roll cage installation techniques.
We are providing you with some measurements to help you set the bars where they need to go to fit other bars. All measurements are not provided.

Make sure the car is level, front to back and side to side

  1. Place car on a flat and level surface. This is critical.
  2. Clean Seam Sealer and get floor to bare metal where the 6×6 plates will land on the floor. Some fitment to the plates may need to be done. As shown here.MOORE-RACE-CHASSIS -FABRICATION-MRC8100N-MRC-Foxbody-Pre-Notched-8-50-Cage-Kit-FIG 4 MOORE-RACE-CHASSIS -FABRICATION-MRC8100N-MRC-Foxbody-Pre-Notched-8-50-Cage-Kit-FIG 5
  3. Once the plates are on the floor, Set the main hoop and tack lightly
  4. The main hoop needs to be leaned back at a 5 degree angle layback to be able to place the rest of the other tubes correctly. A Ratchet strap is useful here to hold the main hoop in place.MOORE-RACE-CHASSIS -FABRICATION-MRC8100N-MRC-Foxbody-Pre-Notched-8-50-Cage-Kit-FIG 6
  5. Once the main hoop is set and tacked. Fit the 12A, 12B, 13 bars
  6. Now, the #11 bar can now be set.
  7. The rest of the bars can now be set in any order. Keeping the above order helps keep the cage square and even as you assemble and tack into place.
  8. The rear down will be placed on the plates provided.

If there’s something this didn’t cover, Please contact us and we can point you in the right direction.

Warranty

Warranty: There is no warranty stated or implied due to unusual stresses placed on race cars and components because we have no control over how they are maintained and used. Moore Race Chassis and fabrication LLC accepts no liability for failures of racing products manufactured or sold by MRC. The customer accepts all risks involved with racing and hazards thereof, MRC makes no claims nor does it intend for it’s products to be used on street driven vehicles.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals