LITHONIA LIGHTING WPX0 LED Wall Pack Instruction Manual

INSTALLATION INSTRUCTIONS
LED WALL PACK
Applique murale WPX DEL Model Number(s)
WPX0 LED

WPX0 LED Wall Pack

Protect yourself. Before installing, read the entire instructions carefully and save them for future reference.
Date installed:____
Failure to follow any of these instructions could void product warranties. For a complete list of product Terms and Conditions, visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.
Upon receipt of fixture, thoroughly inspect for any freight damage. All damage should be reported to the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the inside of the housing to be sure you have received the correct merchandise.
Mounting Hardware and
Mounting Hardware and Silicone Sealant
Required
Purchase Separately
REQUIRED TOOLS:
Description
5/8” Philips Screwdriver
Caulk Gun

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electical code.

• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.

• This fixture is intended to be connected to a properly installed and grounded UL listed junction box.

• It will occasionally be necessary to clean the outside of the refractor/lens.
  Refractor/lens should be washed in a solution of warm water and any mild, nonabrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit.
  Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.

• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting,

WARNING
RISK OF ELECTRIC SHOCK
► Disconnect or turn off power before installation or servicing.
► Verify that supply voltage is correct by comparing it with the luminaire label information.
► Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
► All wiring connections should be capped with UL approved wire connectors.
CAUTION
RISK OF INJURY
► Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
► Avoid direct eye exposure to the light source while it is on.
WARNING
RISK OF BURN
► Allow lamp/fixture to cool before handling. Do not touch enclosure, lens or light source.
► Do not exceed maximum wattage marked on luminaire label.
► Follow all manufacturer’s warnings, recommendations and restrictions including but not limited to: driver type, burning position, mounting locations/methods, replacement and recycling.
CAUTION
RISK OF FIRE
► Keep combustible and other materials that can burn, away from lamp/lens.
► Do not operate in close proximity to persons, combustible materials or substances affected by heat.
CAUTION
RISK OF PRODUCT DAMAGE
► Never connect components under load.
► Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
► Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire must be checked for compatibility with the luminaire prior to installation. LED fixtures must be powered directly off a switched circuit.
► Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or cooling.
► Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature.
► Only use fixture in its intended location.
► LED products are Polarity Sensitive. Ensure proper Polarity before installation.
► Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of unit.
► Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
► Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
► Changes or modifications not expressly approved by Acuity Brand Lighting could void the authority to operate the equipment.
► Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.
► Always ensure that the electrical distribution system is up to NEC (and applicable local code) requirements.
► Verify that power distribution system has proper grounding. Lack of proper earth ground can lead to fixture failure and may void warranty.

All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

This device complies with Part 15 of the FCC Rules but may cause interference with cordless and cell phones, radios, televisions, and other electronic devises.
To correct the problem, move the device away from the luminaire or plug into a different outlet. This product may cause interference to radio equipment and should not be installed near maritime safety communication equipment or other critical navigation or communications equipment operation between. 0.45-30MHz.

5-YEAR LIMITED WARRANTY

Register your warranty on www.acuitybrands.com/resources/warranty. Your prompt product registration confirms your right to the protection available under the terms and conditions of your Lithonia Lighting warranty.
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

FIXTURE PARTS LIST

Description
Quantity

1. Rear Housing ……………………………………………………………………1
2. Door Assembly ………………………………………………………………1
3. 1” 10-24 Screws …………………………………………………….2
4. Tether ……………………………………………………………………..1
5. 5/8” 8-32 Mounting screws* ……………………………………………..2
6. Wire Nuts ………………………………………………………3
   Contained in parts packs

This wall pack is designed to be mounted to a recessed junction box or directly to a flat surface.
CAUTION: DO NOT MOUNT WITH LIGHT AIMING UP, TO AN EXTERNAL JUNCTION BOX, OR OVER RAISED RIBS AS FOUND IN CORRUGATED SIDING
Remove fixture components and parts pack. Check to ensure all parts are included. Note: Account for small parts and destroy packing material, as these may be hazardous to children.
Turn OFF Power at circuit breaker box.
CAUTION: Do not rely on wall switch alone to turn off power

Table – I Choose Settings (Optional)

Switchable Photocontrol| ON/OFF
Color Temperature| 30001C/4000K/5000K
Adjustable Lumens| 1650*
1200
1000
850

*Factory Setting

1. Remove the door assembly (2) from rear housing. Remove and retain Decorative Plugs. Loosen two screws (3) on the front, open door, unhook tether and separate door assembly from rear housing. Note: Do not remove screws completely

2. For junction box mounting, prepare the rear housing for installation by removing the knockout holes as needed, thread house supply wires through the center hole in rear housing and secure the rear housing to junction box using mounting screws (5) provided. See Figure C for detail

3. Reconnect door to rear housing and secure with tether.
   CAUTION: WIRING AND FIXTURE OPERATION Make sure power is turned off.

4. Ground fixture using wire nut to connect the (copper or green) supply ground wire & the green fixture ground wire.
   Note: If wiring does not include a ground wire, consult your local electrical code for approved grounding methods. For proper connection, place wire nut over wires and twist clockwise until tight.

5. Connect supply wires using wire nut to connect the black fixture wire to the black power supply wire and the white fixture wire to the white (neutral) supply wire. Bundle leads and secure to rear housing with provided wire tie to ensure no wires are pinched when closing the door.

6. Close Door and tighten screws to 15-20 in-lbs. Do not over-tighten the screws.
   Note: make sure no wires are pinched before tightening screws. Install Decorative plugs to cover screw heads.

7. Luminaire is preset to 1650 lumens, 4000K CCT, and PE in the On position. If desired, change settings by adjusting the switch. See Figure A/Switch.

8. Turn on electricity at fuse or circuit breaker box and verify success of installation.

For Wet Location compliance, fixture must be properly sealed! Apply caulking to the perimeter of the fixture between the housing and the wall (top and two sides) leaving the bottom side clear of any caulking. Caulking will prevent any water coming down the wall from entering the fixture.
Note: Do not apply caulking on the bottom.
Make sure all wiring access holes are sealed with weatherproof silicone sealant (not included)!

Trouble Shooting Guide

If this fixture fails to operate properly, use the guide below to diagnose and correct the problem.

1. Verify that power is turned on at switch and breaker
2. Verify that line voltage is correct
3. Check wiring and connections.
4. Check if Photocontrol works properly Cover Photocell – Light should come on.

Shine a flashlight into Photocell – Light should go off If fixture cycles on and off:
Light reflecting off any surrounding surfaces, or from other light sources enters the Photocell. To correct problem, eliminate reflective surfaces or reposition the fixture.
Note: NOT suitable for use with dimmers, motion sensors or other remote devices.
If further technical assistance is required, contact:
Technical Support at: 800-705-7378

Cleaning and Maintenance

Caution: Be sure fixture temperature is cool enough to touch.
Do not clean or maintain while fixture is energized.
This LED light provides low maintenance service with no bulbs to change. Clean surfaces with mild soap and water.
Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Acuity Brands Lighting, Inc.
One Lithonia Way, Conyers, GA 30012
www.AcuityBrands.com

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• Post Sales - Consumer Post Sales
• U.S. Environmental Protection Agency | US EPA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>