DigiTech Trioplus Band Creator Looper User Guide

digitech.com
TRIO+
Quick Start Guide
PN: 5064507-A

QUICK START GUIDE

GETTING STARTED

WHAT’S IN THE BOX

• TRIO + Band Creator + Looper
• Power Adapter
• 8 GB Micro SD Card

REGISTER YOUR PRODUCT / GET THE OWNER’S MANUAL
To register your product and download the owner’s manual, please visit http://digitech.com

CONNECT THE TRIO+

A. Turn down the guitar amp or headphone volume. If connecting to a mixer, turn down the gain/trim control and lower the fader on the channel you’re connecting to.

B. Make connections using the diagram to the right for reference.
C. Connect the included power adapter to the TRIO + power input connector then connect the other end to an available AC outlet and wait for the TRIO + to boot.
D. Turn your guitar volume all the way up then strum and gradually increase the guitar amp or headphone volume until the desired level is achieved. If using a mixer, set the channel fader to unity (0) then raise the gain/trim control for the desired level.

ARM THE BAND

NOTE: If the PART buttons are flashing amber, ensure the Micro SD Card is installed in the slot on the left side of the TRIO+ pedal. A Micro SD Card must be installed for the TRIO+ to function.
NOTE: Turn off any style and tempo hints by turning the STYLE knob until all STYLE LEDs are off, and pushing the ALT TIME button until it goes off.
A. Set the BASS and DRUMS levels to about 10 o’clock position.
B. Select the GENRE you want to use for the song part you will be teaching the TRIO+.
C. Press the BAND footswitch to arm the TRIO+ . Keep your guitar quiet until you are ready to strum the first chord. The LED above the BAND footswitch will begin flashing red rapidly.

TEACH THE BAND

A. Start strumming your part in a steady rhythm. You are teaching the TRIO+ a chord progression, so play clearly and avoid embellishments.
B. As you complete your chord progression, press the BAND footswitch just as you strum the same down-beat you started on. The band will now begin playing.
NOTE: To clear the part so you can re-teach the band, see step 10.

CONTROL THE BAND

NOTE: Different GUITAR FX, GENRE, STYLE, SIMPLE BASS, and ALT TIME settings can be selected for each song part.

ARM THE LOOPER

A. Start the band by pressing the BAND footswitch if it is not already playing. B. Set the LOOP level knob to 12 o’clock.
C. Ensure the AUDIOLASTIC LED is off. If it isn’t, adjust the TEMPO control and set it to the 12 o’clock position.
D. Press the LOOPER footswitch to arm the Looper for recording. While the band is playing, the LOOPER LED will flash red rapidly until the band part starts over from the beginning.

RECORD A LOOP

A. Once the band part restarts at the beginning, the LOOPER LED will light solid red indicating the looper is recording. Begin playing the guitar part.
B. When the band part reaches the end, the LOOPER LED will light solid green and the loop you just recorded will now play along with the band.
NOTE: To clear a loop so you can re-record it, see step 10.
A. Begin playing when the LOOP LED lights solid red.

RECORD OVERDUBS

A. Press the LOOPER footswitch once to enable overdub recording. The LOOPER LED will turn solid amber and you can now play an overdub over the loop.
B. When you are done overdubbing, press the LOOPER footswitch to resume Looper play mode. The LOOPER LED will turn solid green again.
NOTE: To clear the last recorded overdub so you can re-record it, see step 10.

REPEAT FOR EACH SONG PART

A. Press the BAND footswitch to stop band/loop playback.
B. Select the next song part using the PART buttons.
C. Repeat steps 3-9 until all parts for the song have been learned and loops recorded.
NOTE: To teach the next part at the same tempo as the previous part, press and hold the new
PART button for 2 seconds to enable a count in metronome for teaching the new part.

CLEARING LOOPS & PARTS

TO CLEAR A PART
A. Press the BAND footswitch to stop band playback.
B. Press and hold the BAND footswitch for 2 seconds until the BAND footswitch LED turns off and then begins flashing red slowly. Press and hold the BAND footswitch again for 2 seconds to restore a cleared part.

NOTE: If a loop is recorded with the band, the loop will be cleared and restored along with the band part.
TO CLEAR A LOOP
A. Press the BAND footswitch to stop loop playback.
B. Press and hold the LOOPER footswitch for 2 seconds until the LOOPER footswitch LED flashes red then turns off. Press and hold the LOOPER footswitch again for 2 seconds to restore a cleared loop.

TO CLEAR AN OVERDUB
A. While the loop is playing, press and hold the LOOPER footswitch for 2 seconds until the LOOPER footswitch LED flashes amber to clear the last overdub. Press and hold the LOOPER footswitch again for 2 seconds to restore the last overdub.
NOTE: Only the last recorded overdub can be cleared. Each time a new overdub is recorded, the previously recorded overdub is mixed with the original loop.

PROGRAM SONG DYNAMICS & SEQUENCE

A. To make a part higher intensity, such as a chorus or the bridge, stop band playback, select the part, then press the PART button again. The LED will light red, indicating the band will play the part more intensely. Repeat for other parts if necessary

B. To program a song sequence, press the SEQ button (the button will begin flashing).

C. Press each PART button in the desired sequence order. Note that you can sequence the same part multiple times.

D. When done, press the SEQ button again.The various PART buttons will flash to indicate the order of the programmed song sequence.

E. The song will now playback in the programmed sequence order when the BAND footswitch is pressed. Turn sequencing on or off by stopping loop/band playback and pressing the SEQ button.

F. To clear the song sequence, make sure the SEQ button is enabled then press and hold the button for 2 seconds (the button will begin flashing). Repeat steps C-D to re-program the song sequence or press the SEQ button to exit Sequence Program mode.

WORKING WITH SONGS

STORING SONGS & LOOPS
All songs and loops are automatically stored to the inserted Micro SD Card in real time. Up to 12 songs with loops can be stored.

SELECT A NEW SONG
A. Press the SONG button.
B. Turn the STYLE knob to select an empty song (the STYLE LEDs will be off for empty songs).
C. Press the SONG button again to exit. Follow steps 3-9 to to add parts.

LOAD A SONG
A. Press the SONG button.
B. Turn the STYLE knob to select a song to load (previously stored songs will be lit dim red).
C. Press the SONG button again to exit.

TO CLEAR A SONG
A. Press the SONG button.
B. Turn the STYLE knob to select the song to clear.
C. Press and hold the SONG button for 2 seconds to clear the selected song.
Note that clearing a song cannot be undone.

Enjoy! And thanks for choosing DigiTech.

© 2022 CORTEK Corp. DigiTech is a registered trademark of CORTEK Corp.
All rights reserved.

References

• DigiTech Home - DigiTech

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>