digitech AR1919 5.8GHz HDMI 1080P Wireless AV Sender User Guide
- June 3, 2024
- Digitech
Table of Contents
5.8GHz HDMI 1080P
Wireless AV Sender
Model: AR1919
Quick Start Guide
PACKAGE CONTENTS
| 1 | 1x Main Unit Transmitter (TX) |
|---|---|
| 2 | 1x IR RX Cable |
| 3 | 1x Main Unit Receiver (RX) |
| 4 | 1x IR TX Cable |
| 5 | 4x Mounting Accessories |
| 6 | 1x 3.5mm Male to Male Cable (for pairing and re-pairing units) |
| 7 | 2x Antennas (same antenna for transmitter and receiver) |
| 8 | 2x Power Adapter (power supplies for transmitter and receiver) |
| 9 | 1x Quick Start Guide |
PORTS AND INTERFACES
| 1 | HDMI In: Connect to Input Sources via HDMI Male Input Port |
|---|---|
| 2 | HDMI Out: Connect to Output Devices via HDMI Male Output Port |
| 3 | DC 5V: DC 5V In |
| 4 | Loop out: HDMI Loop Out Port for Local View |
| 5 | Reset: Hold for 10 seconds to reset, short click to match the Transmitter & |
Receiver
6| IR In: IR Signal Input Port
7| IR Out: IR Signal Output Port
8| Power: Power LED Indicator
9| Link: No connection – Light stays on / Connected: Flashes quickly
10| Status: No video signal: Flashes slowly / Video signal: Flashes quickly
CONNECTION DIAGRAM
FIRST USE
|
---|---
01 Install antennas for Transmitter & Receiver.| 02 Connect the Receiver to
your output display through the “HDMI OUT” port.
|
03 Connect the Transmitter to your media output device through the “HDMI IN”
port.| 04 Connect power to Transmitter and Receiver separately.
|
05 After 10 seconds you will see a loading screen.| 06 After 40 seconds you
will see a screen showing “Searching TX”.
07 Once connected you will see the screen from the output device. (Screen picture for example only)
LED STATUS IDENTIFICATION
Paired Lost / No Match (PtMP)
Power & Link LED is solid, Status LED off
Status LED flash slowly
**** Long press “Reset” for more than 10 seconds will cause the device
configuration to be lost and require units to be repaired.
Normal Mode
Power LED is solid, Status LED flash frequency is faster than Link LED
Power LED is solid, Status LED flash frequency is faster than Link LED
The picture and text here can not correctly describe the working state of the
LED, please refer to it appropriately.
HOW TO PUT THE RECEIVER INTO PAIRING MODE
After the Receiver is reset or when you have purchased two or more receivers and need to pair them to the transmitter.
|
---|---
01 Make sure the Transmitter and Receiver are not powered on.| 02 Open 3.5mm
male-to-male cable.
|
03 Connect the Receiver and Transmitter with the 3.5mm male-to-male cable.| 04
Connect the power adapter of the Receiver and Transmitter.
|
05 After 10 seconds you will see a loading screen.| 06 After 40 seconds you
will see a screen showing “Searching TX”.
|
07 When the display screen shows “SearchingTX”, short press the
“Reset” button in turn on the Receiver and the Transmitter.| 07 Pairing
successful. (Screen picture for example only)
We recommend using up to 2 receivers per transmitter, 1 transmitter can
support up to 4 receivers. If you have multiple Receivers that need to pair,
repeat the pairing actions in this section from steps 01-08.
*Actual wireless environment may increase or decrease pairing time.
TROUBLESHOOTING
| Problem | Cause | Solution |
|---|---|---|
| No picture out after the correct connection at one MOM | Maybe the Transmitter | |
| and receiver have not yet matched the connection | Please follow the operation |
steps:
1. Please connect the Transmitter and receiver with the 3.5mm male to male,
connect Transmitter with an input device, and connect the receiver with the
display;
2. Supply power on both Transmitter and receiver;
3. Long press the reset button for Los on the receiver until the display
shows the OSD content “searching TX”;
4. Short press the reset button on either receiver or both sides
simultaneously to match the Transmitter and receiver automatically, the Link
and Status LED both flash quickly means the Transmitter and receiver is
connected well. If customers want to connect more receivers, they can repeat
these steps to match one Transmitter up to four receivers simultaneously
No picture out after correct connection at different room| The distance can’t
reach 100m due to the signal loss via passing through the solid walls.| When
passing through a solid wall (thickness under 30cm), the signal will lose 30%
of the original signal and the distance will be shorter than 70m; if passing
through two or more solid walls, the distance will be shorter than 20m. Please
get a shorter distance at pass through solid wall application
The picture out not stable or the distance is shorter than the description|
Maybe there have some same band Interference sources at 5GHz affect the
extender’s signal transmission.| Please place the product closer when there
have the same bond Interference sources or remove the Interference sources
Distributed by:
Electus Distribution Pty. Ltd.
320 Victoria Rd, Rydalmere
NSW 2116 Australia
www.electusdistribution.com.au
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>