Olink Target 48 Test Kit Instructions

: June 9, 2024
: Olink

Table of Contents

Olink Target 48 Test Kit
Short instructions
Detection
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Olink Target 48 Test Kit

Short instructions

Incubation

Prepare the Incubation mix in a microcentrifuge tube according to the table below.

Incubation mix per ½ 96-well plate (μL)

Olink® 1-48 plex Incubation Solution 168
Olink® Target 48 Frw-probes 21
Olink® Target 48 Rev-probes 21
Total 210

Vortex and spin down the Incubation mix. Transfer 23 μL of the Incubation mix to each well of a new 8-well strip.
Transfer 3 μL of Incubation mix to each well of the first 6 columns of a 96-well plate by reverse pipetting and name the plate Incubation Plate.
Add 1 μL of each sample using a multi-channel pipette to the bottom of the well, 1 μl of Sample Control to the three top wells (yellow), 1 μL of Negative Control to two wells (red), and 1 μL of Calibrators to three wells (green), according to the plate layout.
Seal the plate with an adhesive plastic film, spin at 400 – 1000 x g, 1 min at room temperature. Incubate overnight at +4 °C.
Thaw the PEA Solution over night at +4 °C, and place the PEA Enhancer at room temperature over night.

Extension

Prepare an extension mix according to the table below.

Extension mix per ½ 96-well plate (μL)

High Purity Water (+4 °C) 4350
Olink® 1-48 plex PEA Enhancer 580
Olink® 1-48 plex PEA Solution 580
Olink® 1-48 plex PEA Enzyme 58
Total 5 568

Bring the Incubation Plate to room temperature, spin at 400 – 1000 x g for 1 min. Preheat the PCR machine.
Vortex the Extension mix and pour it into a multichannel pipette reservoir.
Start a timer for 5 min and transfer 96 μL of Extension mix to the upper parts of the well walls of the Incubation Plate by using reverse pipetting.
Seal the plate with a new adhesive plastic film, use the MixMate® to vortex the plate at 2000 rpm for 30 sec, ensuring that all wells are mixed, and spin down.
Place the Incubation Plate in the thermal cycler and start the PEA program. (50 °C 20 min, 95 °C 5 min (95 °C 30 sec, 54 °C 1 min, 60 °C 1 min) x 17, 10 °C hold)

Detection

Prepare and prime an Olink® 48.48 IFC for Protein Expression. Briely, inject one control line fluid syringe into each accumulator on the chip, remove the protective film from the bottom of the IFC and then prime the IFC on the Olink® Signature Q100 following the instructions on the instrument screen.
Thaw the Primer Plate, vortex and spin briefly.
Prepare a Detection mix according to the table below.
Detection mix per ½ 96-well plate (μL)
Olink® 1-48 plex Detection Solution 275.0
High Purity Water 116.0
Olink® 1-48 plex Detection Enzyme 3.9
Olink® 1-48 plex PCR Polymerase 1.5
Total 396.4
Vortex the Detection mix and spin briefly and add 46 μL of the mix to each well of an 8-well strip.
Transfer 7.2 μL of the Detection mix to each well of column 1-6 in a new 96-well plate by reverse pipetting, and name it Sample Plate.
Remove the Incubation Plate from the thermal cycler, spin down the content and transfer 2.8 μL to the Sample Plate, using forward pipetting.
Seal the plate with an adhesive film, vortex and spin both at 400 – 1000 x g, 1 min at room temperature.
Transfer 5 μL from each well of column 1-6 of the Primer Plate and 5 μL from each well of column 1-6 of the Sample Plate into the primed 48.48 IFC left and right inlets, respectively. Use reverse pipetting and change tips after each primer or sample. Do not leave any inlets empty.
Remove bubbles and load the IFC in the Olink Signature Q100 and follow the instructions on the instrument screen.
Run the IFC on the Olink Signature Q100.

www.olink.com
© 2023 Olink Proteomics AB. Olink products and services are For Research Use Only and not for Use in Diagnostic Procedures. All information in this document is subject to change without notice. This document is not intended to convey any warranties, representations and/or recommendations of any kind, unless such warranties, representations and/or recommendations are explicitly stated. Olink assumes no liability arising from a prospective reader’s actions based on this document. OLINK and the Olink logotype are trademarks registered, or pending registration, by Olink Proteomics AB. All third-party trademarks are the property of their respective owners. Olink products and assay methods are covered by several patents and patent applications https://www.olink.com/patents/. Olink Proteomics, Dag Hammarskjölds väg 52B , SE-752 37 Uppsala, Sweden 1126, v1.3, 2023-01-18