ZEVNI A04476 4-Light Black-White Transitional Chandelier Instruction Manual
- June 9, 2024
- ZEVNI
Table of Contents
- ZEVNI A04476 4-Light Black-White Transitional Chandelier Instruction
- Item Number: A04476
- IMAGE FOR FINISHED PRODUCT:
- OOLS REQUIRED (NOT INCLUDED):
- +1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
- ACCESSORIES & QTY ENCLOSED:
- ASSEMBLY & INSTALLATION INSTRUCTIONS:
- 1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
- 3. Turn off power
- 4. Make installation
- ORDERING PARTS
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEVNI A04476 4-Light Black-White Transitional Chandelier Instruction
Item Number: A04476
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides.n Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products
IMAGE FOR FINISHED PRODUCT:
OOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation pl
+1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
PARTS TYPE & QTY INCLUDING:
(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Collar ring (1)
(G) Collar loop (1)
(H) Quick link (2)
(I) Chain (1)
(J) Loop (1)
(K) Upper frame (1)
(L) Nut (8)
(M) Stem (1)
(N) Lampshade (4)
(O) Threaded tube (4)
(P) Socket (4)
(Q) Sockets assembly (1)
(R) Lower frame (1
ACCESSORIES & QTY ENCLOSED:
(A) Wire connector (3)
(B) Mounting screw (2)’
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make preinstallation
Step A1 » Pass fixture wires through stem (M), upper frame (K) and loop (J), then screw loop (J) and stem (M)
Step A2 »together onto the top of sockets assembly (Q) to secure upper frame (K).
Insert threaded tubes (O) into upper frame (K), and secure them with nuts (L).
Step A3 » Insert threaded tubes (O) into lower frame (R), and secure them with nuts (L).
1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
Step B1 » By measuring, determine the correct number of links needed for
proper hanging height. Using the chain pliers, disconnect and discard the
unwanted part.
Step B2 Attach quick link (H) to chain (I) and loop (J) on the top of upper
frame (K)
Step B2 Carefully weave the fixture wires through chain (I) in and out of
every other link and stop just when ou reach the top of chain (I). Gently pull
the wires to ensure the wires are not stressed.
3. Turn off power
Before you start the installation, NEVER attempt any work without shutting off
the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Make installation
Step C1 » Remove collar ring (F) from collar loop (G). Attach single bar (C)
to the outlet box with mounting screws (B).
NOTE: the side of single bar (C) marked “GND” must face out.
Step C2 » Raise canopy (E) over collar loop (G) and screw collar ring (F) to
measure a proper position.
Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to
the following note, you would know the proper position where collar loop (G)
should be located.
NOTE: canopy (E) should be snug against the ceiling and collar loop (G) should
be screwed enough threads (no less than 6 threads) on the preassembled
threaded nipple for more secure hanging. If not, adjust collar loop (G) on
single bar assembly (C) by screwing collar loop
(G) in or out of single bar (C) until the secure length is achieved.
Step C3 » Pass chain (I) through collar ring (F) and then through canopy (E).
Step C4 » Open quick link (H), attach quick link (H) to collar loop (G). Close
quick link (H). Pass the fixture wires through collar loop (G) to the top of
the preassembled threaded nipple and gently pull to ensure the wires are not
stressed.
Step C5 » If needed, shorten the length of fixture wires. At this point, the
remaining wire length measuredabove single bar (C) is at least 6″.
Twist wires together with plastic wire connectors until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step C6 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS
BARE
COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Step C7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by
tightening collar ring (F) onto collar loop (G).
Step C8 » 1) Install bulbs (not included) (Please do not exceed the maximum
wattage recommended on the socket.)
2) Carefully slide two metal wires of lampshades (N) along bulbs and check if
metal wires hold bulbs properly.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use
exact wording from illustration when ordering parts.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>