ZEVNI A04407 Mordy 4.7-in 1-Light Black/Brass LED Modern Instruction Manual

June 9, 2024
ZEVNI

ZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern
logo

ZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern

ZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern
product

Instruction

Item Numbe r: A04407
WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 5W per bulb.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:ZEVNI A04407 Mordy 4.7-in 1-Light Black Brass
LED Modern 01

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below pictureZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern
02

PARTS INCLUDING

  • (C) Green ground screw (1)
  • (D) Mounting plate (1)
  • (E) Back plate (1)
  • (F) Stud (1)
  • (G) Movable joint (1)
  • (H) Knob nut (2)
  • (I) Swivel joint (1)
  • (J) Socket (1)
  • (K) Glass shade (1)

ACCESSORIES ENCLOSED:

  • (A) Mounting screw (2)
  • (B) Plastic wire connector (3)ZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern 03

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home.
      Place the main power switch in the “OFF” position.

    • Place the wall switch in the “OFF” position.

Make assemblyZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern
04

  • Step A1 » Unscrew knob nuts (H) from back plate (E), then set them aside for later installation.

  • Step A2 »

    • Carefully pull the fixture wires from movable joint (G).
    • Put movable joint (G) and back plate (E) together, then lay wires in the fluted side of movable joint (G).
    • Put movable joint (G) and back plate (E) together again, and secure them with stud (F).
  • Step A3 »Carefully pass the supply wires from the outlet box through mounting plate (D).
    Secure mounting plate (D) to the outlet box with mounting screws (A).

  • Step A4 » Make wire connections
    Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

    • Connect ground wires according to the below chartZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern 05
    • Connect wires according to the below chartZEVNI A04407 Mordy 4.7-in 1-Light Black Brass LED Modern 06Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
  • Step A5 » Align the holes in back plate (E) with the pre­assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (H). Hand tighten until snug.
    NOTE: back plate (E) should be snug against the wall with knob nuts (H).
    If not, remove back plate (E), adjust the threaded length of pre­assembled mounting screws on mounting plate assembly (D):

    • first, unscrew the pre­assembled hex nuts;
    • then, screw the pre­assembled mounting screws in or out of mounting plate (D);
    • when the secure length is achieved, tighten the pre­assembled hex nuts and back to Step A5.
  • Step A6 » Screw glass shade (K) onto socket (J).
    To adjust the angle of light by swivel joint (I): Press socket (J) up and down within 90 degrees.

Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non­abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
www.ihomeangel.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ZEVNI User Manuals

Related Manuals