elgato 10LAB9901 Key Light Air User Guide
- June 4, 2024
- elgato
Table of Contents
10LAB9901
User Guide
Assemble Key Light Air
| 
---|---
|
Software Installation
| 
---|---
|
Key Light Air requires a 2.4 GHz network with WPA or WPA2 encryption. Your
system must therefore be Wi-Fi enabled, and Key Light Air must be within range
of your router.
If your PC is not equipped with Wi-Fi, use the Elgato Control Center app on
your iOS or Android device to add Key Light Air. A Wi-Fi connection is only
needed for initial pairing. One Key Light Air is paired, you can control it
via any wired or wireless device in your network.
Warning
- Key Light Air may become hot during prolonged use. Always handle with care.
- Do not cover this product, especially the ventilation holes.
- Do not place on or near a carpet, curtains, or any other flammable materials.
- Be especially cautious when setting up near children.
- Do not attach items to Key Light Air or its stand.
- Do not leave Key Light Air in direct sunlight.
- Do not set up in areas susceptible to strong air currents. Drafts and breezes can cause movement that may result in damage to Key Light Air.
- Keep the lighting surface free from dirt and dust. If Key Light Air becomes dirty, wipe it lightly with a soft cloth moistened with a little water and mild, neutral detergent. Benzene, thinner, and other volatile agents can cause permanent damage and should never be used for cleaning.
- Always place Key Light Air on a flat and firm surface. Uneven or unstable surfaces may cause tipping and result in damage or personal injury.
- Do not use the stand for applications other than those specified in this guide or the packaging.
For indoor use only Frequency range: 2412 – 2472 MHz (2462 MHz for FCC, ISED),
Max RE e.i.r.p power < 20 dBm, Temperature range: 0 °C – 45 °C Hereby, Corsair
Memory Inc declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EC. The
declaration of conformity for Elgato products is available at
www.elgato.com/doc
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment. This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator and the human
body.
For questions about Elgato product compliance with FCC regulations, please
contact: Compliance Officer, Corsair Memory Inc., 115 North McCarthy Blvd,
Milpitas, CA 95035, USA
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Elgato, a division of
Corsair Memory Inc., 115 North McCarthy Blvd, Milpitas, CA 95035, USA
Corsair Memory, BV Wormerweg 8,1311 XB, Almere, Netherlands
Copyright 2018 – 2022 Corsair Memory Inc. All rights reserved. Elgato and the
Elgato logo are trademarks of Corsair Memory
Inc., registered in the U.S. and other countries.
Part: 51LAB9907
R-R-CSI-20LAB9901
R-R-CSI-B1026-1302006X
Applicant Name: Corsair Memory, Inc.
Product Name: Key Light Air
Model No: 20LAB9901
Manufactured Year & Month: Please refer to the gift box sticker
Manufacturer & Origin: Corsair Memory, Inc./ Made in Taiwan
A/S: 1522-1460
