EVICIV MDS-7B06 7 Inch Touchscreen Display Screen User Manual

EVICIV MDS-7B06 7 Inch Touchscreen Display Screen

WARNING
Please read this user manual carefully before using the device.
This product has been designed with personal considerations in mind, but incorrect use may cause electric shock and fire.
To avoid damaging the safety parts inside the machine, please observe the following rules during installation, installation, use, and repair:

1. To prevent fire or electric shock, please do not put the monitor in humidity or even in a worse condition;
2. Before using the device, make sure all cables are connected properly and the power cord is not damaged, if there is any damage, please contact us immediately;
3. To avoid dust, moisture, and extreme temperatures, please DO NOT place the device in any DAMP area. Please place the device on a stable surface when in use.
4. DO NOT put any object or splash any liquid into the openings of the device casing;

MOST IMPORTANT NOTE:
Please use our original power charger and power cable, contact our professional After-Sales Service Team if any problems occur.
We will give you the best solution within 12 hours.

To avoid personal injury, please observe the following rules:

1. Do not place the monitor on a sloping table unless there are security measures;
2. Do not drop or throw objects or toys onto the screen, because it will result in personal injury, product and screen damage;

To prevent other injuries, please observe the following rules:

1. Please turn off the monitor when you leave for a long time;
2. Do not allow Children to throw or put objects into the monitor;
3. Do not install spare parts that are not specifically designed for this device;
4. Please Unplug the power cord when the device is unattended for a long time.
5. Do not touch the power cord or signal cable when lightning strikes, otherwise it may cause electric shock;
6. Do not let any object compress or wrap the power cord;
7. Do not place the monitor where the power cord can be easily damaged.

To prevent machine damage, the following situations should be avoided:

1. Place the monitor where is easy to fall;
2. Place the display near a radiator or heat source;

• Do not rub the screen with a hard object as it will scratch or permanently damage the screen.
• Do not use your fingers to press the screen for a long time, otherwise it will produce screen smear, and even screen damage.
• Red, green, and blue pixel defects may appear on the screen, but it does not affect the display function.
• The power cord is the main isolation device and must be put in an Easy-to-operate place.
• If possible, try to use the recommended resolution for the best results.
• Because if you use other resolutions other than the recommended resolution, a screen abnormality may occur.
• But this is a feature of an LCD panel with a fixed resolution.
• A still picture on the screen for a long time will cause damage to the screen and produce afterimages.
• Please make sure to use the screen saver, because the afterimage and related issues are not covered in the scope of product repairing warranty.
• If you encounter any technical problems while using this device, please contact our professional After-Sater Service Team immediately, we will provide you with the best solution within 12 Hours.

Ways Of Holding

Ways suggested when holding the monitor.

Ways NOT suggested when holding the monitor.

Function of main accessories

Interface function introduction

• A. Power Button
  Press button for 3 seconds to turn on/off the monitor

• B. Menu Button
  Press to enter the 05D (On-Screen Display) menu

• C. UP Button
  Volume +/Brightness+

• D. Down Button
  Press to return to the previous operation

• E. Exit Button
  Press to return to the previous operation

• F. Speakers
  Speakers

• G. Audio Port
  Audio output interface 3.5mm audio jack

• H. HDMI Input Port
  Signal transmission

• I. Type-C Input Port
  Audio Nideo/Touch Signal Transmission

• J. DC12V
  DC12V Input Port

• K. Stand Holder
  Built-in invisible stand holder

Internal Structure

1. Place the monitor where it is easy to fall
2. Place the display near a radiator or heat source

Reserved interface for cooling fans
User customize button to control the Backlight (For Raspberry Pi 10 Control) (EN OV=off 3.3V=on)
(PWM 3.3V=brightest OV=darkest)

Air Cooling System

Turn on the fan after the Raspberry Pi is built-in

Air Cooling System

Please pay attention not to rip off the fan cable when you open the case.

Product Parameters

The display supports horizontal and vertical rotation, and you need to set it in your computer device:
Extended mode – vertical rotation 90 degrees I 270 degrees.

OSD Menu introduction

PICTURE

Press ‘Menu’ button to enter screen setting.
Twice press ‘Picture’ to enter picture setting.
Double press enter Picture’ setting.
Press ‘UP’ or ‘DOWN’ to adjust brightness or contrast.

COLOR

Press ‘Menu’ button to enter screen setting.
Then press ‘Down’ button to choose ‘COLOR’.
Double press enter ‘COLOR’ setting.
You can adjust ‘Red’ ‘Green’ ‘Blue’ by press ‘UP’ or ‘DOWN’.

DISPLAY

‘DISPLAY’ is default setting. The ‘Aspect Ratio’ is 16:9.

SETUP

Press ‘Menu’ button to enter screen setting-
Press ‘DOWN’ button to choose ‘SETUP – Double press ‘SETUP to choose Language’.
There are 12 languages too choose.
Press menu to choose ‘Menu H-Position’ Menu V-Position’ “Menu Timer ‘Audio Volume’ by pressing up or down to adjust.

Input Sources Switching

The exit button is a shortcut key for input sources switching, the menu is displayed in the upper right corner.

HDMI-IN
When connecting the device via HDMI port.

HDMI-RPI
When installing Raspberry Pi to the monitor.

Type-C
When connecting the device via Type-C port. (Please kindly note the Type-C port just for signal input or U-C cable for touch. It can not power supply the display.

Function introduction

Regarding the connection method as a Pl monitor.

Connect to Pl3

Step 1:
Method 1
Solder the 3pin touch cable to the Raspberry Pi 38+ motherboard. (If it is not soldered, the touch function cannot be used).

• PP51 — Black Cable GND.
• PP43 — Green Cable USB-DP.
• PP42 — White Cable USB-DM.

Plug the 3 Pin touch cable into the monitor board.

Method 2
Plug the USB end of the 3 Pin touch cable into the USB port of the Raspberry Pi 3B+motherboard.
Plug the other end into the monitor board.

Step 2:
Insert the adapter board (HDMI-A and Micro USB) to the Raspberry Pi 3B+ motherboard.
PS: If you need to change other Pl or you do not need the touch function, just skip step 1 and step 2.

Step 3:
Insert the Pl3 Side Panel (note the Pl3 position), and fix the Raspberry Pi board to the monitor motherboard.

Step 4:
Screw the shell.

Step 5:
Connect the DC power adapter to the monitor.

Connect to Pl4

Step 1:
Method 1
Solder the 3pin touch cable to the Raspberry Pi 48 motherboard. (If it is not soldered, the touch function cannot be used).

• PP20 — Black Cable GND.
• PP19 — Green Cable USB-DP.
• PP18 — White Cable USB-DM.

Plug the 3 Pin touch cable into the monitor board.

Method 2
Plug the USB end of the 3 Pin touch cable into the USB port of the Raspberry Pi 48 motherboard.
Plug the other end to the monitor board.

Step 2:
Insert the adapter board (HDMI-D and Type-CJ to the Raspberry Pi 4B motherboard. PS: If you need to change other Pl or you do not need the touch function, just skip step 1 and step 2.

Step 3:
Insert the Pl4 Side Panel (note the Pl4 position), and fix the Raspberry Pi board to the monitor motherboard.

Step 4:
Screw the shell.

Step 5:
Connect the DC power adapter to the monitor.

Touch Rotation

The touch screen rotation can solve the user’s adjustment of the underlying code of the system and reduce the development cycle.
The capacitive touch screen can be rotated clockwise in the menu setting:
0/90/180/270, 0 is the default normal horizontal screen—Please Kindly Note: touch rotation is for the touch function not for screen rotation.

Regarding the connection method as a common monitor

Connect to PC

1. Power Cable
   Please use the configured 12V adapter for power supply.

2. USB A to C cable
   for touch.

3. HDMI Cable
   signal transmission.

If there is no touch function, please refer to the picture to check whether the touch cable is connected correctly. You can change the connection with other computer equipment to verify whether there is a problem with the touch interface.
Please note that one end of the touch cable needs to be connected to the monitor and the other end to the computer equipment, host computer, Raspberry Pi or other H DM I devices.
When the monitor is connected to a game device or the monitor’s touch end is connected to a power source, socket, or other power supply devices, it cannot be touched.

1. Computer with Type-C interfaces and supports Thunderbolt.
2. Computer with HDMI interface.
3. Connect to a mobile phone with Type-C interface (USB 3.1}(with touch function}.
4. Android phone with Type-C interface but not USB 3.1 or without Type-C port Ii Phone (touch function is not supported}.

Note: The touch function can’t be achieved by some phones which don’t support USB 3.1.

FAQ and Solution

• Q: Why the monitor can not be turned on even though the Raspberry Pi has been installed?
  • A:
  1. Please make sure that the main board of Raspberry Pi is connected correctly.
  2. Please be sure that you use the provided DC power adapter to power up the monitor.
• Q: Why is there no touch function after installing the Raspberry Pi?
  • A: You need to solder the 3 pin touch cable to the Raspberry Pi board. Please refer to page 14 or 20 for the specific connection method. If you have any further questions, please contact us.
• Q: Why there is no touch function with HDMI connection?
  • A: Be sure to connect the U-C cable.
• Q: Why is the monitor getting hot?
  • A: It is recommended that you turn on the cooling system.
• Q: Why the monitor can not be turned on after the Raspberry Pi is installed and power adapter is connected properly?
  • A:
  1. Connect the computer to confirm whether the monitor can display normally
  2. If there is no problem with the monitor, download the software from the official website of Raspberry Pi to install and check whether the adapter board is aligned and inserted.
• Q: Why is there no full screen on the monitor?
  • A: Please set the monitor as the main screen.
• Q: Why the touch function is inaccurate when the monitor is set as a second display?
  • A: Please set the monitor as the main screen.

Warranty Card

Dear Customer:
Thank you for purchasing from us!
We offer 100% money back guarantee within 30 days and replacement within 90 days, lifetime warranty for any issue, professional tech support to ensure no- worry service.
Any query or problem, please contact us via
US: support@eviciv.com
EU: monitor@eviciv.com
we will reply to you within 12 hours.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>