ZEVNI A04786 Yuba 3-Light 11-in Black Flush Mount Light Instruction Manual

ZEVNI A04786 Yuba 3-Light 11-in Black Flush Mount Light

Item Number: A04786

WARNING (To reduce the risk of fire, electric shock, or personal injury)

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
4. Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
5. Place the wall switch in the “OFF” position.
6. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
7. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
8. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
9. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
10. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
11.  The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

1. (A) Plastic Wire Connector (3)
2. (B) Mounting screw (2)
3. (C) Single bar (1)
4. (D) Green ground screw (1)
5. (E) Canopy (1)
6. (F) Socket (3)
7. (G) Hex nut (1)
8. (H) Cap nut (1)
9. (I) Glass shade (3)
10. (J) Socket ring (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

3. Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.

4. Place the wall switch in the “OFF” position.

5. Unscrew hex nut (G) and cap nut (H) from single bar (C).

6. Secure single bar (C) to the outlet box with mounting screws (B).
   NOTE : the side of single bar (C) marked “GND” must face out.

7. Make wire connections Connect wires as below wires connection shown. REFER TO THE FOLLOWING CHARTS, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Twist wires together with plastic wire connector (A) until tightly joined, and wrap each connector with approved electrical tape for a more secure connection, then carefully tuck all wires into the outlet box. Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening hex nut (G) and cap nut (H) onto the pre -assembled threaded nipple on single bar (C).

NOTE: The canopy (E) should be snug against the ceiling and cap nut (H). If not, adjust the threaded length of the pre-assembled threaded nipple on single bar (C):

• First, unscrew the pre-assembled hex nut.
• Then, screw the pre-assembled threaded nipple in or out of single bar (C).
• When the secure length is achieved, tighten the pre-assembled hex nut and back to step 6.

1. Remove socket rings (J) from sockets (F), and carefully place glass shades (I) on sockets (F), then secure glass shades (I) with socket rings (J).
2. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is already installed properly, then you could turn on the light. Enjoy! www.ihomeangel.com

+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST

homecustomercare@outlook.com

References

• HOMEANGEL LLC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>