TOPDON BTMOBILE Lite 12V Cordless Battery and System Tester User Manual

TOPDON BTMOBILE Lite 12V Cordless Battery and System Tester

Compatibility

Please be noted that battery type and CCA values (Cold Cranking Amp) marked on the battery label. Please refer to it before using BT MOBILE lite.

• Regular Flooded
• AGM Flat plate
• AGM Spiral
• GEL
• EFB

FEATURES

APP Installation & Setup

Installation Download and install the App: “BT MOBILE” in Apple Store or Google Play.

Setup : For the first time, you can choose to register with email or skip login

Drop-down Menu Function:

Operation Introduction

Before Test

• Before you test a battery in a vehicle, turn off the ignition, all accessories, and loads. Close all of the vehicle’s doors and trunk lid.
• Make sure the battery terminals are clean. Use a wire brush to clean them, if necessary.
• Connect the RED(+) Positive Battery Clamp to the(+) positive battery terminal, and connect the BLACK (-) Negative Battery Clamp to the (-) negative battery terminal. Ensure that the clamps are securely attached to the correct terminals.
• Open the Bluetooth on the mobile phone.
• Test Introduction
• BATTERY TEST: Display SOH (State of Health), SOC (State of Charge), Voltage, Current, Rating, and the readable analysis results on App;
• CRANKING TEST: Analyze the actual cranking voltage and the cranking time to help you quickly figure out the whole state of the starting system;

Battery Test (for 12V battery)

• Open the APP on your mobile device and log in.
• Click the flashing Bluetooth logo in the upper right corner of the home screen, to enter the connection interface, and search for the matching device name.
• If the Bluetooth connection is successful, the Bluetooth logo will stop flashing.
• Click the matching device name to connect.
• Click “Battery Test” on the home screen and click “Start”
• Select the battery type and click “OK” to confirm.
• Select the battery standard marked on the battery label, and click “OK” to confirm.
• Select battery capacity value marked on the battery label and click “OK” to confirm
• Click “Next” and wait a few seconds for results
• Drop down to share the results

Cranking Test

The engine and all other accessory loads must be OFF during the test.

• * Click “Cranking Test” on the home screen, and then click “Start” 

  • Follow the steps and start the vehicle.
  • Drop down to share the result

Charging Test

• * Click “Charging Test” on the home screen, then click “Start”.

  • Follow the steps and start the vehicle.
  • Step on the accelerator, increase the number of RPM to 2500, keep it for 5 seconds.
  • Click “Next” to get the results
  • Drop-down to share the results.

System Test (Overall Test for Battery)

• * Select “System Test” in the upper right corner, or swipe the home screen left to the system test options

  • Click “Start” to enter System Test operation interface and complete all tests (refer to Battery Test. Cranking Test, Charging Test for details). Click the right arrow to access to each test result report
  • Click “System Test” to access to each test result report

Technical Specification

• Working Temperature: -20°C~65°C (-4 °F~ 140°F)
• Storage Temperature: -20°C~ 70°C (-4°F~ 158°F)
• Dimensions: 81 •68•27 mm (3.19•2.68• 1.06 inches)
• Weight: 250 g (8.81 oz)

Warranty

TOPDON Two Years Limited Warranty
The TOPDON Company warrants to its original purchaser that TOPDON products will be free from defects in material and workmanship for 24 months from the date of purchase (Warranty Period). For the defects reported during the Warranty Period, TOPDON will, according to the technical support analysis and confirmation, either repair or replace the defective part or product. O This limited warranty is void under the following conditions

Warnings

• DO NOT place the tester near the engine or exhaust pipe to avoid damage from high temperatures.
• DO NOT smoke, cause sparks, or strike matches near the battery when testing.
• DO NOT remove battery clamps while testing.
• DO NOT put the tester into a highly humid or dusty environment.
• DO NOT disassemble the tester

Cautions

• Use this tester in accordance with these instructions, taking into account the working conditions and the work to be performed.
• Hazardous results could occur if the tool is used for purposes not intended.
• Before testing, make sure the battery terminals are clean. Grease and dust could result in inaccurate test results.
• Wear eye protection when working around batteries.
• Check the insulation layer of the battery clamps is in good condition (no damage, bareness, or disconnection) to avoid electric shock.
• Test in a well-ventilated area. Vehicle exhaust contains toxic carbon monoxide.
• Keep hair, hands, and clothing as well as tester leads and cords away from moving blades and belts.
• Keep the tester out of the reach of children

FAQ

• Q: Is BT MOBILE lite able to test vehicle alternator?
  • A: It can test the alternator.
• Q: Is BT MOBILE lite able to test motorcycle batteries?
  • A: It can test the 12V battery, between 100 and 2000 CCA. If the motorcycle battery is within these values, then yes.
• Q: How to set the CCA range?
  • A: You can set the data near to the CCA standard number of your battery.
• Q: Is BT MOBILE lite able to test 12V deep cycle batteries?
  • A:Yes.
• Q: Will BT MOBILE lite work with marine batteries?
  • A: Yes, it can work with marine batteries.Q: What do SOH, SOC, and BAT mean?
  • A: The SOH refers to the “State of Health”. The SOC is the “State of Charge” and the BAT is the “Resistance Value” of the battery.
• Q: Will this accurately load test ATV batteries?
  • A: Yes, it can accurately load test ATV batteries.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>