ASUS DRW-24B1ST Optical Disc Drive Internal DVD User Manual

**ASUS DRW-24B1ST Optical Disc Drive Internal DVD

**

Safety information

Observe the following precautions before installing and using the drive.

Installation Notices

• Do not place this device in an unstable position, or on vibrating surfaces.
• Do not place this device under direct sunlight or in humid or damp places.
• Do not use or place this device near magnetic fields, televisions, or radios to avoid electronic interference that affect drive performance.
• Do not attempt to disassemble or repair the drive. Opening the drive may result to exposure to laser radiation.
  WARNING! Do not remove the front panel and/or tray door to avoid the fly- out of the rotating disc.

Using the Device

• Do not place damaged discs inside the device. A damaged disc may break while in use and damage the device
• Use of any controls, adjustments, or procedures other than those specified in this manual may result to hazardous radiation exposure.
• Do not attempt to disassemble the drive.
• Do not move the device from a cold to a warm or hot environment. Drastic change in temperature is harmful to the device.
• Before moving or uninstalling the drive, remove any disc in it.
• Prevent liquids or any metal from getting into the device, If this situation occurs, contact your retailer for help
• Do not use any evaporating solvents to clean the device. If you accidentally sprayed any solvent on the device, use a clean cloth to wipe it. You may also use a neutral cleaner to dilute the solvent to easily wipe it from the device.
• Do not turn off the computer while the device is in reading or writing mode.
• Do not place discs into the device immediately if they came from a cold environment, specially during cold seasons. Wait until the discs have reached room temperature
  [CLASS 1 LASER PRODUCT]

WARNING:
This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Hardware installation

Tum off your computer and any peripheral device connected to ii before installing the optical drive. For avoiding damage to the optical drive due to static electricity, use a grounded wrist strap or touch a safely grounded object or a metal object, such as a power supply case, before installing the optical drive.

1. Remove the computer cover.

2. For IDE optical drives, configure the drive jumper to set the device to either Master, Slave, or Cable Select mode before installing ii into the chassis.

3. For SATA optical drives, there is no necessity for jumper settings.

4. Insert the optical drive into an available 5.25-inch bay (as shown in Figure 1 ).

5. For IDE optical drives, connect a 4-pin power supply cable to the DC input connector of the optical drive (as shown in Figure 2). Next, connect an IDE cable to the IDE connector at the back of the optical drive, matching the colored stripe on the cable with Pin 1 on the IDE connector (as shown in Figure 2). Connect the other end of the IDE cable to the IDE connector on the motherboard.

6. For SATA optical drives, connee1 a 15-pin power supply cable to the DC input connector of the optical drive (as shown in Figure 3). Next, connect a SATA cable to the SATA connector at the back of the optical drive (as shown in Figure 3). Connect the other end of the SATA cable to the SATA connector on the motherboard.

7. Slide the optical drive into the bay and secure it with four screws.

8. Replace the computer cover.

9. Tum on your computer.

Australia Statement Notice

From 1 January 2012 updated warranties apply to all ASUS products, consistent with the Australian Consumer Law. For the latest product warranty details please visit http://support.asus.com. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at http://support.asus.com.

Declaration of compliance for product environmental regulation

ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements.

Please refer to http://csr.asus.com/Compliance.htm for information disclosure based on regulation requirements ASUS is complied with:

EU REACH and Article 33
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.

EU RoHS
This product complies with the EU RoHS Directive. For more details, see
http://csr.asus.com/english/article.aspx?id=35.

India RoHS
This product complies with the India E-Waste (Management) Rules, 2016 and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials and 0.01% by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule II of the Rule

Vietnam RoHS
ASUS products sold in Vietnam, on or after September 23, 2011,meet the requirements of the Vietnam Circular 30/2011/TT-BCT

Turkey RoHS
AEEE Y6netmeliQine Uygundur

ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

Compliance Statement of Innovation, Science and Economic Development

Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES-003[B)/NMB-003[B)

FCC COMPLIANCE INFORMATION

PerFCCPart2SecUoa2.1077

Responsible Party: Asus Computer International
Address: 48720 Kato Rd, Fremont, CA 94538
Phone/Fax No: (510)739-3777/(510)608-4555

hereby declares that the product compliance statement
These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) These devices may not cause harmful interference, and (2) these devices must accept any interference received, including interference that may cause undesired operation.
Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC60825-1 Ed. 3., as described in Laser Notice No. 56,dated May 8, 2019.

Simplified UKCA Declaration of Conformity
ASUSTeK Computer Inc. hereby declares that this device is in compliance with he essential requirements and other relevant provisions of related UKCA Directives. Full text of UKCA declaration of conformity is available at www.asus.com/support

Software installation

Wi11dows® 8.1/10111 automatically detects the current settings for your drive and installs the appropriate driver. (English)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>