onn 100123973 Rugged Mini Speaker User Guide

100123973 Rugged Mini Speaker
User Guide Rugged Mini- Speaker
100123973
WM_ONN
DP Audio 100123973
BTS Mini Speaker
OPT03_QSG 12/30/2022
Filename: WM_ONN_DP Audio_100123973_BTS Mini Speaker_OPT03_QSG_C
Date: 30 Dec 2022
Stock: 157g C2S
Size: 22.75″ x 4.48″

Overview

Buttons

Power Button
Press and hold to turn the speaker on/off.
Press to show current battery level.
Volume Up/Next Button
Press to turn up the volume.
Press and hold to go to next song.
Multi-function Button
Press to pause/play the current track.
Press to accept an incoming call.
Press again to hang up.
Press and hold to reject an incoming call.
Volume Down/Previous Button
Press to turn down the volume.
Press and hold to go to previous song.
Bluetooth° Button
Press and hold to activate Party Sync Mode.
Press to switch between AUX/FM/Bluetooth* modes.

Charging Your Device

Plug the included USB-C cable into the speaker’s charging port, and connect the other end of the cable to a power adapter (sold separately). Allow approximately 3 hours to fully charge the battery.
Note: We recommend using a USB wall adapter with a 5V output.
Press the Power button to check current battery level.

Initial Setup

1. Once your device is fully charged, press and hold the Power button until you hear a prompt indicating the de-vice has entered Bluetooth* pairing mode.
2. On your smartphone or tablet, search for the Blue-tooth’ device named “onn. bts mini spkr” and tap to connect.
3. A prompt will play once pairing is successful.

Party Sync Mode

This device features Party Sync Mode technology, which allows you to play music on two of these mini-speakers simultaneously, creating a surround sound experience.

1. Press and hold the Power button on both speakers to turn them on and enter Bluetooth’ Pairing Mode.
2. On your smartphone or tablet, search for the Blue-tooth’ device named “onn. bts mini spkr” and tap to connect to one of the speakers.
3. Press and hold the Bluetooth’ button on the speaker that is connected to your smartphone or tablet.
4. You will hear a sound prompt while the speakers are pairing. The status light will illuminate on both speakers once connected.

AUX Mode
Connect your external device to the AUX input on the side of the speaker via AUX cable (sold separately) to enter AUX mode and start streaming audio from your device. Press the Bluetooth’ button to exit AUX mode.
NOTE: An AUX cable (sold separately) must be connect-ed to detect AUX mode.

FM Radio Mode

1. Switch to FM Radio mode by pressing the Bluetooth’ button.
2. Press and hold the Multi-function button to auto-matically scan for radio stations. Press and hold the Multi-function button again to remain on a selected channel.
3. To manually scan for radio stations, press and hold the Previous and Next buttons.

Insert the included USB-C cable into the Charging Port while in FM mode to use it as an external antenna and improve signal.

Hands-Free Calling Controls

Volume Down/Previous Button
Press once to decrease volume
Volume Up/Next Button
Press once to increase volume
Multi-function Button
Press to accept an incoming call. Press again to hang up. Press and hold to reject an incoming call.

Reset

If your speaker is not operating properly, you may reset it. To do so, press and hold the Power button for approx-imately 8 seconds until the speaker powers off, and then power it on again as usual.

Specs

Speaker Output Power
3W RMS
Bluetooth Speaker Frequency Response
150 Hz -16000 Hz
Battery
Built-in rechargeable
Battery Life
Up to 13 Hours’
IPX5
Water-resistant, rainproof, sprayproof, and splashproof
Modes
Bluetooth’ Mode Party Sync Mode” AUX Mode FM Radio Mode
Range
33 ft (10m)
Input
AUX USB C
‘Battery life measured as number of playtime hours with volume set at 50%.
“Can pair with another onn.” Rugged Mini-Speaker. Will NOT pair with the onn? Mini Rugged Speaker series 8100081667

FCC Warning

This device complies with Part 15 of the FCC Rules. Oper-ation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undesired operation.
Caution
Changes or modifications to this product not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm-ful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit differ-ent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-cian for help.

This device has been evaluated to meet general RF ex-posure requirements.
The device can be used in portable exposure conditions without restriction.
FCC ID: 2AVRV100123973

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>