Lucci decor 031079 Presly Dimmable Colour Shifting LED Pendant Instruction Manual

Installation Instructions

PRESLY DIMMABLE COLOUR SHIFTING LED PENDANT
SKU# 031078, 031079
Rated Voltage 220-240V~ 50Hz

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation, and use of this luminaire. Please keep instructions for future reference.

Warranty

• This luminaire is covered by a 3-year warranty. The warranty is from the date of purchase, not the date of installation.
• If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
• Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty inquiries.
• The use of non-compatible dimmers may damage your LED luminaire and will void the warranty.
• Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• This luminaire must be assembled and installed by a licensed electrician.

• All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
  E.g. AS/NZS 3000 Electrical Installations.

• This luminaire is a Class I product and must be earthed during wiring and installation.

• Select a suitable location for installation:
  − This luminaire is suitable for indoor use only.
  − The mounting point must support 2 times the weight of the luminaire.
  − Ensure the luminaire is not installed in the direct line of an air vent/system.
  − If installing a luminaire in an area prone to moisture, ensure that the area is well-ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.

• The colour shifting function will only operate with a mechanical or relay ON/OFF switch.

• The colour shifting function will not operate with a semi-conductor ON/OFF switch.

• This luminaire is dimmable and was tested with the dimmers listed in the specification table at the date of publication.

• The use of a LED dimmer such as the Lucci LEDlux SKU# 290998, SKU# 290997, SKU# 290992 or SKU# 290993, 290994 or SKU# 299043, or Buster + Punch DIM-002, dimmer is highly recommended.
  NOTE: For the best dimming range, use the Lucci LEDlux SKU# 290998 dimmer and adjust the variable resistor at the minimum and maximum dimming positions on the dimmer during the installation.
  NOTE: Dimming may cause buzzing sounds or a slight flicker. There may be slight delays with the LED luminaire start-up or slightly uneven light performance when more than one LED luminaire is linked together, switched ON, or dimmed. This is not a product fault and as such is not covered under warranty.
  NOTE: Some dimmers have a minimum load of 20W. Ensure the dimmer position is on the maximum setting before turning on the luminaire and adjusting the dimmer down to your desired light level.
  NOTE: Testing cannot account for installation variables such as variation in mains supply voltage, cable capacitance, electrical noise, transients, surges and ripple control signals (commonly found in NSW & QLD).
  NOTE: The information provided is correct to the best of Beacon Lighting’s knowledge at the date of publication.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

• Lay out all the components on a smooth surface and make sure no components are missing before assembling.
  If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair, or replacement.

Installation Directions

NOTE: Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
NOTE: Due to the size and weight of the luminaire, two people will be required to lift it up during the installation process.

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.

2. Use the mounting bracket (B) as a template to mark the screw positions on the ceiling and drill the holes.

3. Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (D) and anchors (A). Ensure the screws (D) and anchors (A) are suitable for the mounting surface and the surrounding environment.

4. Determine the length of the suspension rods (K, L, M, N) required for your installation location. Install the required lengths of suspension rods (K, L, M, N) onto the body of the luminaire (O).
   NOTE: Pull the luminaire LED wires (black, red, and white) out as you install the suspension rods (K, L, M, N) to remove any slack. Take care not to cross thread or twist and damage the luminaire LED wires.

5. Place and loop the locking nuts (J) onto the suspension rods.

6. Place and loop the canopy (I) onto the suspension rods.

7. Lift up the luminaire and attach the top of the suspension rod to the threaded rod on the mounting bracket (B).
   NOTE: Secure the suspension rod onto the mounting bracket by tightening the nuts (C) with the spanner provided.

8. Connect the luminaire LED wires (black, red, and white) to the terminal block (H – output end of the LED driver (G)). Ensure the wires are secure and no bare wires are exposed.

9. Open the terminal box (E) and connect the mains supply wire to the terminal block (F).
   Mains Supply Wire
   Earth – Yellow/Green
   Neutral – Blue or Black
   Live – Brown or Red| Luminaire Wire / Terminal Block
   Yellow/Green
   Blue or N
   Brown or L
   ---|---

NOTE: The luminaire is a Class I product and must be earthed during wiring and installation.
NOTE: Ensure the earth wiring is secure and correct, by performing an earthing continuity test.

10. Ensure the wires are secure and no bare wires are exposed.
11. Install the cover back onto the terminal box (E) and ensure the cover is firmly fixed.
12. Lift up the canopy (I) and install it onto the mounting bracket (B) by tightening the locking nuts (J).
13. Carefully insert the glass rods (P) into the side of the luminaire.
14. Install the end-cap (Q) onto the end of the luminaire, it is held in position by magnets.
15. After the installation is complete, switch on the luminaire to test and enjoy your new lighting product.
16. To operate the colour shifting function, use the wall switch.
    − While the luminaire is on, toggle the wall switch OFF and ON again within 3 seconds.
    − The colour shifting sequence will jump from 3000K – 4000K – 5000K.
    − For the colour shifting to memorise the colour temperature, leave the wall switch OFF for over 7 seconds.

To reset the colour shifting, toggle the wall switch OFF and ON twice within 1 second. Repeat if it doesn’t reset.

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, or making any adjustments to the luminaire.
• To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
• The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced. There are no serviceable parts, do not attempt to dismantle or open the luminaire.
• Select a suitable location away from liquids and hazards.
• To clean, wipe with a soft damp clean cloth. Do NOT soak or immerse the luminaire in water or other liquids.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.

Specifications

Specifications| |
---|---|---
SKU #| 031078| 031079
Colour| Matte Black| Brass Finish
Rated Voltage| 220-240V— 50Hz
Rated Wattage| 37W Max.
Insulation Class| Class I
LED Specs| Colour Shifting *LEDs, ****Dimmable, ****CRI >90
Lumens| 3000K — 3000 lumens
4000K — 3250 lumens
5000K — 3350 lumens
Highly
Recommended
Dimmers| Luce’ LEDIux SKU# 290998,
Lucci LEDIux SKU# 290997, 290992,
Lucci LEDIux SKU# 290993, 290994,
Lucci LEDIux SKU# 299043,
Buster + Punch DIM-002.
Compatible
Dimmers| Clipsal PDL354RDMLED-VW, 31E2RUDM, 32E450TM, 32E450UDM, 31E2PUDM, 32ELEDM.
DIGINET LED Smart MEDM.
LUMEX Load Smart LT1D450LS
HPM Cat. 4001
Weight| 7.6kg
Canopy
Dimensions| H:45mm L:600mm W:65mm
Luminaire
Dimensions| H:135mm L:1510mm W:80mm Susp:1800 Max.**

• NOTE: The colour shifting function will only operate with a mechanical or relay ON/OFF switch.
  The colour shifting function will not operate with a semi-conductor ON/OFF switch.

v 1 . 0 (12 / 2 0 21)

Documents / Resources

| Lucci decor 031079 Presly Dimmable Colour Shifting LED Pendant [pdf] Instruction Manual
031078, 031079, 031079 Presly Dimmable Colour Shifting LED Pendant, 031079, Presly Dimmable Colour Shifting LED Pendant, Pendant, LED Pendant
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>