ZHIDATECH K Series Charging Station User Manual

K-Series Charging Station
US Standard
User manual

Safety precaution:

1. Please read the instructions carefully before use. You should follow the steps in the instructions.
2. Please do not dismantle the product. Wrong disassembly can cause product damage, leakage and water seepage.
3. The installation and maintenance of the charger must by a qualified electrician operation; Any unqualified personnel shall not be responsible for the problems caused by the above operation.
4. Any incorrect installation and repair can leave the user in a dangerous condition.
5. Do not connect the power supply and keep the open circuit status before the installation and maintenance complete.
6. Adapters or conversion adapters are not allowed.
7. Ensure that the incoming end is installed on a dedicated circuit breaker (MCB). The circuit breaker must contain a residual current device (RCD) and match the input electrical parameters.

Packing list :

Place the product on the table and open the product packaging. (Schematic)

Products and contents of the box:
K-series charger, charging card, expansion screw, instruction manual certificate of conformity

Product Features:

General Specifications

Model| ZDYDKBL0311100/ZDYDML0200000
Cable Length| 5m
Charging Mode| Mode 3
Dimension| 310x 210 x 90mm (without cable)
Weight| 4.6kg
Operating Temperature| – 40 °C to 65 °C
Storage Temperature| – 40 °C to 85 °C
Normal operating altitude| ≤4000m
Standards| IEC 61851-1, IEC 61851-22, IEC 62196-2
Electrical Specifications
Rated Input/Output Voltage (V)| 165-265
Rated Input/Output Current (A)| 32
Rated Input/OutputFrequency (Hz)| 60Hz
Output power| 7.4kw
Connector Type(SAE J1772)| Type 1
Cable Width| 3 x 6mm2
Protection Rating| IP66 / IK10

Installation Notes:

The charger installation environment meets the following conditions:

1. The installation location must fully consider the cable length and user charging convenience;
2. Charging piles should not be installed in places with severe shocks and flammable and explosive materials;
3. Charging piles should not be installed in places with low terrain and possible accumulation of water;
4. The charger should be installed in a well ventilated place;
5. The installation environment requires cleaning;
6. There should be no other equipment or articles within 50cm of the upper and lower left and right sides of the charging pile installation wall;
7. Installation conditions are as follows:

Install Process:

1. Installation tools:
   Preparation: (impact drill M8 drill bit, electric screwdriver, gradient)
   The mounting screws are already included in the fitting

2. Installation steps:
   a. Choose a wall of the right strength that can withstand at least 100kg of pulling force.
   b. Remove the front shell of the charging pile and the four screws that hold the hanging plate, and then remove the hanging plate.
   c. Using the hanging plate and the level, select the appropriate height on the wall (recommended to be 1.2-1.4 meters off the ground), and use a pen to mark the punching
   d. Punch four mounting holes in the wall according to the marked position: the size of the hole is 10x65mm
   e. Place the hanging plate in the welled hole position and place it in the provided expansion spiral. Use a Phillips screwdriver to screw in the 5×70 screw to preserve a distance of 5-8mm from the wall.
   f. Attach the pile to the back plate and lock the removed fixing screws.
   g. Remove the four screws from the junction box and remove the cover.
   h. Place the incoming cable into the Cable Gland and correspond to the L, N, and PE terminal interfaces of the terminals. Once the wire is connected, lock the Cable Gland.
   i. Close the inlet terminals, cover the junction box panel to lock the screws, and cover the front enclosure.
   j. The installation is complete

Operation Instruction:

Start charging
Before charging, the charging cable and connector should be inspected for damage, foreign objects, water ingress or impurities.
Connect charging piles and vehicles
The charging pile light strip turns into a blue light flashing quickly, waiting for the start
We use an RFID card to start charging close to the swipe area The blue-green spaced strips of light flicker breathlessly The K-series LED light turns green with slow flashing when it starts charging.

Stop charging
Swipe the RFID card again and stop charging
The charging pile turns green and the car stops being charged Pull charging connector from the car charging inlet, cover the protective sleeve on charging connector and wrap the cable around the pile enclosure

until LED light turns blue, breathing flicker
| LED Light green light blinks breathlessly| K-series is charging your car| Your car is charging
| LED Light red, flashing| K-series is experiencing the error| Check the troubleshooting chapter In this manual for solutions. If not, contact the supplier of our product.

Troubleshooting：

Note: The above faults are tested and diagnosed by professional electricians. We are not responsible for any re-damage or safety hazards caused by improper personal operation.

check the ground
Red flashes 7 times| Urgent stop failure| Turn on the red button in the lower right corner clockwise
Red flashes 8 times| Short circuit| contact us
Red flashes 9 times| Overtemperature| contact us
Red flashes 10 times| Measurement fault| contact us
Red flashes 11 times| Temperature chip failure| contact us
Red flashes 12 times| Leakage self-inspection failure| contact us
Red flashes 13 times| Relay adhesion| contact us
Red flashes 14 times| Output short circuit| contact us

Warranty, Repair & Maintenance:

ZD Tech promises its products without any material and process defects during the warranty period. During the warranty period due to normal use of the product failure, ZD will repair and replace parts for users.
Any hardware or software faults caused by the quality problems of the product itself during the warranty period shall be served by the authorized maintenance resources

Disclaimer

1. Accidental damage caused by the customer’s transportation of the product.
2. Product failure or damage caused by incorrect installation caused by installation of the customer or use in a non-product-defined working environment.
3. Damage to the appearance of the product (Such as burns, squeezing deformation, etc.).
4. The product has been repaired by personnel unauthorized by ZDTECH or its authorized service personnel.
5. Damage due to irresistible factors (such as earthquakes, floods, etc.).
6. Products that exceed the warranty period.

Declaration:

Communication Regulations (FCC)
This device complies with Part 15 of the FCC rules and Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>