Gisemi Microelectronics G01-SPIPX-N 2.4G Module User Manual
- June 8, 2024
- Gisemi Microelectronics
Table of Contents
Gisemi Microelectronics G01-SPIPX-N 2.4G Module User Manual
A. Product Overview
G01-SPIPX-N is a 160mW industrial wireless data transceiver with high speed and high stability, operates at ISM band 2.4GHz. The module uses original Si24R1. It comes with high-performance IPEX antenna and accurate impedance matching. The module is equipped with a shielding cover to effectively enhance the anti-interference capability. It features enough power, good spectral properties, small harmonic wave, small cross talk, and super small volume. Some of the devices meet military grade standard.
-
Comes with IPEX antenna, transmission distance up to 2.0km [ 1 ]
-
Super low power consumption, the lowest power consumption is about 2uA
-
Operation frequency 2.4-2.4835GHz channels
♦ Frequency adjustable,1MHz stepping
♦ GFSK modulation -
3 FIFO levels
♦ Transmission length:1-32 bytes each data packet
♦ Receiving length: 1-32 bytes each data packet
♦ Automatically resend mechanism
♦ Support data transmission of 6 channels -
Communication interface
♦ Hardware SPI interface of 4-Pin
♦ 4Mbps data speed is recommended, Max speed is up to 10Mbps. -
Multiple levels of wireless data rate
♦ 3 levels of wireless data rate are optional: [2] 250Kbps, 1Mbps -
4 operation modes [4] ♦ Power down
♦ Standby
♦ Send
♦ Receive -
Supply voltage range
♦ 2.0V-3.6VDC -
Receiving sensibility
♦ -99dBm (data speed 1Mbps)
♦ -108dBm (data speed 250Kbps) -
Ultra-small volume, SMD package
♦ 13 * 19mm
♦ Module weight is about 0.5g -
Ultra-small volume, in-line package
♦ 12 * 19mm
♦ Module weight is about 3.5g
Remarks:
- Open, sunny, no obstacles; The max power, height 2m, data speed 250Kbps
- The airspeed is higher, the distance is closer. The wireless data rate is lower, the distance is longer.
- For transmitting power, please see chip manual of Si24R1
- For four operation modes, please see chip manual Si24R1
- Voltage higher than 3.6V will damage the module permanently
C. Series products
D. Electrical Parameters
Test condition: Tc = 25℃，VCC = 3.3V
- Voltage higher than 3.6V will damage the module. The lower the voltage, the lower the transmission power.
- Power supply capability must be greater than 30mA.
E. Module Functions
5.1 Recommended Connection Diagram
- High level CE is valid. When the module writes the register, it must first be set to power-down mode. It is recommended to connect CE to the IO port of the micro-controller.
- IRQ is recommended to connect the external interrupt of the micro-controller. Alternatively, the SPI query mode can be used to obtain the interrupt status.
- The Si24R1 technical manual requires that the high-level time of the CE pin is greater than 10us to start data transmission. However, to make the same code compatible with our G01 series modules with PA and LNA, it is recommended to change CE to high level after setting the SPI operation. After the completion of the transmission, continue to maintain a high level of 1ms, and then lower the CE.
5.2 Pin Definition
5.3 Pin Function
Function of IRQ Pin
IRQ is an interrupt mapping pin, which is active at low level. Refer to the Si24R1 chip manual for the specific interrupt signal it represents.
CE pin function
The module control pin, the module’s transmit mode (TXD) and receive mode (RXD) are determined by this pin. See the Si24R1 chip manual for details.
Function of SPI pin
The SPI sequence diagram is as follows:
F. Package Information
6.1 Overall dimension(unit: mm)
6.2 Reference Pad Design (unit: mm)
G. Package
7.1 Electrostatic Bag Package (unit: mm)
Important Remarks and Disclaimers
As the hardware and software of the product continue to improve, this manual
may be subject to change, andthe final version of the manual shall prevail.
Users of this product need to pay attention to the product dynamics on the
official website, so that userscangetthe latest information of this product in
time.
The pictures and diagrams used in this manual to explain the functions of this
product are for referenceonly. The measured data in this specification are all
measured by our company at room temperature for referenceonly. Please refer to
the actual measurement for details. Chengdu Gisemi Electronics Co., Ltd.
reserves the right of final interpretation and modification of all
contentsinthis manual.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy a nd, if not installed and used in accordance with the instructions, may cause harmful interference to radio com medications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help important
announcement Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled
environment. This equipment should be installed and operated with minimum
distance 20cm
between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. Country Code
selection feature to be disabled for products marketed to the US/Canada.
This device is intended only for OEM integrators under the following
conditions:
- The antenna must be installed such that 20cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna,
Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following” Contains FCC ID: 2ANIVG01″
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
2.3 Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
2.4 Limited module procedures
Not applicable
2.5 Trace antenna designs
Not applicable
2.6 RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
2.7 Antennas
This radio transmitter FCC ID:2ANIV-G01 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID:2ANIVG01″.
2.9 Information on test modes and additional testing requirements
Host manufacturer which install this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result comply with FCC part 15.247 and 15.209 requirement, then the host can be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.
ISED Statement
English: This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, a nd (2) This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES 3 (B)/NMB 3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Note Important:
In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the Canada authorization is no longer considered valid and the ISED cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following: Contains IC: 22889-G01
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>