ZEVNI A04429 38 Inch Wide Black LED Kitchen Island Light Instruction Manual

ZEVNI A04429 38 Inch Wide Black LED Kitchen Island Light

Instruction

Item Number: A04429
WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 21W.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

| | | |
---|---|---|---|---
Ladder| Philips Head or Flat Blade Screwdriver| Electrical Tape| Pilers| Wire Cutter/Stripper

PARTS TYPE & QTY INCLUDING

• (C) Mounting plate (1)
• (D) Screw (4)
• (E) Canopy (1)
• (F) Lock nut (3)
• (G) Steel wire (2)
• (H) Cable (1)
• (I) Tube (2)
• (J) Threaded pipe (2)
• (K) Fixture body (1)
• (L) Socket (4)
• (M) Lampshade (4)
• (N) Socket ring (4)

ACCESSORIES & QTY ENCLOSED

• (A) Mounting screw (2)
• (B) Wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

3. Make installation

• Step A1 »  Unscrew screws (D) from mounting plate (C) and canopy (E).
• Step A2 » Attach mounting plate (C) to the outlet box with mounting screws (A).
• Step A3 » Make wire connections

Connect wires as below wires connecting shown. PLEASE NOTE THAT GROUND WIRE IS BARE
COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Make wire connections

Connect wires according to the below chart

Connect Black or Red Supply Wire to:| Connect

White Supply Wire to:

---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

*Note: When parallel wires (SPT I& SPTll)areused.Theneutralwireis squareshapedorridgedandthe otherwirewillberoundinshapeor smooth(seeillus.)

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

• Step A4 » Raise canopy (E) to the ceiling and secure canopy (E) in place by threading screws (D) into canopy
• Step A5 »
  • Screw tubes (I) onto the top of threaded pipes (J).
  • Remove socket rings (N) from sockets (L), and carefully place lampshades (M) on sockets (L), then secure them with socket rings (N).
  • To adjust the hanging height of the fixture:(E) and mounting plate (C).
  • Press down and hold lock nuts (F) by hand.
  • Pull or push cable (H) and steel wires (G) in and out of canopy (E) to increase or decrease the hanging height.

Check everything is already installed properly, then you could turn on the light. Enjoy!

+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST

homecustomercare@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>