Vitrum

Vitrum VI EU on-off 6 triac 921.7 MHz

SKU: 01EB6S263

Quickstart

This is a
secure
On/Off Power Switch
for
.

To run this device please connect it to your mains power supply.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Vitrum can easily be installed in common flush-mounting boxes, and does not require buses, control units or additional wiring. It uses the most widespread technologies in the world, and offers an advanced and intuitive user experience and is offered in different collections to choose the style that best suits your needs. The great versatility of Vitrum simplifies home automation and makes it available to everyone.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 20| Lifeline reportAdd Controller Node ID to the list of Node ID destinations belonging to the Lifeline Group, in order to let the controller receive Central Scene Notification report andDevice Reset Locally Notification reports.Lifeline report with End Point informationAdd both Controller Node ID and Controller End Point to the list of End Points belonging to the Lifeline Group, in order to let the controller receive Central Scene Notification report with the End Point source address information. That may be achieved by sending the Multichannel Association Set Command Class and filling Multi Channel Node ID field with the Controller Node ID and End Point field with the Controller End Point.
---|---|---
2| 20| Add Node IDs to the list of Node ID destinations belonging to the Button 1 Control group in order control the added nodes by sending Basic Set commands.
3| 20| Add Node IDs to the list of Node ID destinations belonging to the Button 2 Control group in order to control the added nodes by sending Basic Set commands.
4| 20| Add Node IDs to the list of Node ID destinations belonging to the Button 3 Control group in order to control the added nodes by sending Basic Set commands.
5| 20| Add Node IDs to the list of Node ID destinations belonging to the Button 4 Control group in order to control the added nodes by sending Basic Set commands.
6| 20| Add Node IDs to the list of Node ID destinations belonging to the Button 5 Control group in order to control the added nodes by sending Basic Set commands.
7| 20| Add Node IDs to the list of Node ID destinations belonging to the Button 6 Control group in order to control the added nodes by sending Basic Set commands.

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 10: Button N.4 Off status LED

Color of LED associated to push-button N.4 reporting an off state.
Size: 1 Byte, Default Value: 3

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 11: Button N.5 Off status LED

Color of LED associated to push-button N.5 reporting an off state.
Size: 1 Byte, Default Value: 3

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 12: Button N.6 Off status LED

Color of LED associated to push-button N.6 reporting an off state.
Size: 1 Byte, Default Value: 3

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 13: Button N.1 On status LED

Color of LED associated to push-button N.1 reporting an on state.
Size: 1 Byte, Default Value: 4

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 14: Button N.2 On status LED

Color of LED associated to push-button N.2 reporting an on state.
Size: 1 Byte, Default Value: 4

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 15: Button N.3 On status LED

Color of LED associated to push-button N.3 reporting an on state.
Size: 1 Byte, Default Value: 4

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 16: Button N.4 On status LED

Color of LED associated to push-button N.4 reporting an on state.
Size: 1 Byte, Default Value: 4

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 17: Button N.5 On status LED

Color of LED associated to push-button N.5 reporting an on state.
Size: 1 Byte, Default Value: 4

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 18: Button N.6 On status LED

Color of LED associated to push-button N.6 reporting an on state.
Size: 1 Byte, Default Value: 4

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 206: Buttons Max. Brightness

Maximum brightness of LEDs associated to push-buttons.Remark: value must be grateror equal than Parameter N.207.
Size: 1 Byte, Default Value: 100

SettingDescription

Parameter 207: Buttons Min. Brightness

Maximum brightness of LEDs associated to push-buttons.Remark: value must be lessor equal than Parameter N.206.
Size: 1 Byte, Default Value: 5

SettingDescription

Parameter 209: Buzzer

Buzzer operating status.
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 218: Front-end Buttons lock

Buttons lock status
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 25: Output port connected to Button N.1

Output port connected to Button N.1.Remark: connecting a button to an output port already connected to another different button, will force the previously connected button to be automatically disconnected
Size: 1 Byte, Default Value: 1

SettingDescription

0 – 6| 0: Disconnected; 1: Button connected to Output Port 1; 2: Button connected to Output Port 2; 3: Button connected to Output Port 3; 4: Button connected to Output Port 4; 5: Button connected to Output Port 5; 6: Button connected to Output Port 6.
---|---

Parameter 26: Output port connected to Button N.2

Output port connected to Button N.2.Remark: connecting a button to an outputport already connected to another differentbutton, will force the previously connectedbutton to be automatically disconnected
Size: 1 Byte, Default Value: 2

SettingDescription

0 – 6| 0: Disconnected; 1: Button connected to Output Port 1; 2: Button connected to Output Port 2; 3: Button connected to Output Port 3; 4: Button connected to Output Port 4; 5: Button connected to Output Port 5; 6: Button connected to Output Port 6.
---|---

Parameter 27: Output port connected to Button N.3

Output port connected to Button N.3.Remark: connecting a button to an outputport already connected to another differentbutton, will force the previously connectedbutton to be automatically disconnected
Size: 1 Byte, Default Value: 3

SettingDescription

0 – 6| 0: Disconnected; 1: Button connected to Output Port 1; 2: Button connected to Output Port 2; 3: Button connected to Output Port 3; 4: Button connected to Output Port 4; 5: Button connected to Output Port 5; 6: Button connected to Output Port 6.
---|---

Parameter 28: Output port connected to Button N.4

Output port connected to Button N.4.Remark: connecting a button to an outputport already connected to another differentbutton, will force the previously connectedbutton to be automatically disconnected
Size: 1 Byte, Default Value: 4

SettingDescription

0 – 6| 0: Disconnected; 1: Button connected to Output Port 1; 2: Button connected to Output Port 2; 3: Button connected to Output Port 3; 4: Button connected to Output Port 4; 5: Button connected to Output Port 5; 6: Button connected to Output Port 6.
---|---

Parameter 29: Output port connected to Button N.5

Output port connected to Button N.5.Remark: connecting a button to an outputport already connected to another differentbutton, will force the previously connectedbutton to be automatically disconnected
Size: 1 Byte, Default Value: 5

SettingDescription

0 – 6| 0: Disconnected; 1: Button connected to Output Port 1; 2: Button connected to Output Port 2; 3: Button connected to Output Port 3; 4: Button connected to Output Port 4; 5: Button connected to Output Port 5; 6: Button connected to Output Port 6.
---|---

Parameter 30: Output port connected to Button N.6

Output port connected to Button N.6.Remark: connecting a button to an outputport already connected to another differentbutton, will force the previously connectedbutton to be automatically disconnected
Size: 1 Byte, Default Value: 6

SettingDescription

0 – 6| 0: Disconnected; 1: Button connected to Output Port 1; 2: Button connected to Output Port 2; 3: Button connected to Output Port 3; 4: Button connected to Output Port 4; 5: Button connected to Output Port 5; 6: Button connected to Output Port 6.
---|---

Parameter 31: Basic Set On from Group 2

Value of the Basic Set command sent:0: 99 (0x63)1: 255 (0xFF)
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 32: Basic Set On from Group 3

Value of the Basic Set command sent:0: 99 (0x63)1: 255 (0xFF)
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 33: Basic Set On from Group 4

Value of the Basic Set command sent:0: 99 (0x63)1: 255 (0xFF)
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 34: Basic Set On from Group 5

Value of the Basic Set command sent:0: 99 (0x63)1: 255 (0xFF)
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 35: Basic Set On from Group 6

Value of the Basic Set command sent:0: 99 (0x63)1: 255 (0xFF)
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 36: Basic Set On from Group 7

Value of the Basic Set command sent:0: 99 (0x63)1: 255 (0xFF)
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 7: Button N.1 Off status LED

Color of LED associated to push-button N.1 reporting an off state.
Size: 1 Byte, Default Value: 3

SettingDescription

0 – 7| LED is off: 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 8: Button N.2 Off status LED

Color of LED associated to push-button N.2 reporting an off state.
Size: 1 Byte, Default Value: 3

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Parameter 9: Button N.3 Off status LED

Color of LED associated to push-button N.3 reporting an off state.
Size: 1 Byte, Default Value: 3

SettingDescription

0 – 7| 0: LED is off; 1: Red; 2: Green; 3: Blue; 4: Yellow; 5: Magenta; 6: Cyan; 7; White.
---|---

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Basic
• Central Scene V3
• Configuration V2
• Device Reset Locally
• Manufacturer Specific V2
• Multi Channel Association V3
• Multi Channel V4
• Node Naming
• Powerlevel
• Security 2
• Supervision
• Switch Binary
• Transport Service V2
• Version V2
• Zwaveplus Info V2

Controlled Command Classes

• Basic

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>