Hank Smart Plug HKZW-SO08P Manual
- June 8, 2024
- HANK
Table of Contents
- Hank
- Smart Plug
- SKU: HKZW-SO08P
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Quick trouble shooting
- Association – one device controls an other device
- Configuration Parameters
- Parameter 151: Threshold of power report
- Parameter 152: Percentage threshold of power report
- Parameter 171: Power report frequency
- Parameter 172: Energy report frequency
- Parameter 173: Voltage report frequency
- Parameter 174: Electricity report frequency
- Parameter 20: Overload protection
- Parameter 21: Setting device status after power failure
- Parameter 24: Notification when Load status change
- Parameter 254: Enable/disable the configuration command
- Parameter 27: Indicator modes
- Technical Data
- Supported Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Hank
Smart Plug
SKU: HKZW-SO08P
Quickstart
This is a
secure
On/Off Power Switch
for
CEPT (Europe).
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
Add for inclusion (non-security and security):1)Connect the power supply.2)Set
the Z-Wave network main controller into learning mode.3)Triple click the
Z-button, the LED indicator will be flashing 3 times in Blue.4)Smart Plug
should be recognized and included into the Z-Wave network.
Please refer to the
Manufacturers
Manual
for more information.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
Smart Plug is a Z-Wave Switch plugin module specifically used to enable Z-Wave command and control (on/off) of any plug-in tool. It can report wattage consumption or kWh energy usage. This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products.Smart Plug is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.This device must be used in conjunction with a Security Enabled Z-Wave Controller in order to fully utilize all implemented functions.Features:1) AC output switch on/off by manual or Z-Wave command;2) RGB LED indicates the Z-WAVE network range and load power;3) Support S0 and S2 security network;4) Supporting power meter;5) Supporting repeater role;6) Supporting firmware OTA;7) Supporting Smart Start;8) Supports over-current protection
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave
controller. This
procedure should only be used when the primary controller is inoperable.
Long press the button for 20 seconds and the blue LED will speed up the flash and then LED will keep on for 3 seconds in blue and Smart Plug will send Device Reset Locally Notification to the main controller and exclude from the Z-Wave network, this procedure will reset Smart Plug to factory default. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-
specific
installation guidelines/norms may do works with mains power. Prior to the
assembly of
the product, the voltage network has to be switched off and ensured against
re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Inclusion
Add for inclusion (non-security and security):1)Connect the power supply.2)Set the Z-Wave network main controller into learning mode.3)Triple click the Z-button, the LED indicator will be flashing 3 times in Blue.4)Smart Plug should be recognized and included into the Z-Wave network.
Exclusion
- Insert the Plug into a socket.2) Set the Z-Wave network controller into the exclusion mode. 3) Triple click the Z button.4) LED will blink in blue for 3 times, and then start slow flashing to indicate that the remove for exclusion is successful. LED will indicate network status after it is removed from Z-Wave network.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1 | 5 | Z-Wave Plus Lifeline |
---|
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock
further
enhanced features.
IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus
56.
In case of a two byte value the same logic applies: Values greater than 32768
may
needed to be given as negative values too.
Parameter 151: Threshold of power report
Power threshold to be interpreted, when the change value of load power
exceeds the setting threshold, the smart plug will send meter report to
association device (Group Lifeline).
Size: 2 Byte, Default Value: 50
SettingDescription
0 – 200 | Available settings: 0 – 200 (0 – 200W) |
---|---|
0 | 0 – The function is disabled. |
Parameter 152: Percentage threshold of power report
Power percentage threshold to be interpreted, when change value of the load
power exceeds the setting threshold, the smart plug will send meter report to
association device (Group Lifeline).
Size: 1 Byte, Default Value: 10
SettingDescription
0 – 100 | Available settings: 0 – 100 (0 – 100%) |
---|---|
0 | The function is disabled. |
Parameter 171: Power report frequency
The interval of sending power report to association device (Group
Lifeline).
Size: 4 Byte, Default Value: 3600
SettingDescription
3600 – 2678400 | Available settings: 3600- 2678400 (3600 – 2678400s) |
---|---|
0 | The function is disabled. |
Parameter 172: Energy report frequency
The interval of sending energy report to association device (Group
Lifeline).
Size: 4 Byte, Default Value: 7200
SettingDescription
3600 – 2678400 | Available settings: 3600- 2678400 (3600 – 2678400s) |
---|---|
0 | The function is disabled. |
Parameter 173: Voltage report frequency
The interval of sending voltage report to association device (Group
Lifeline).
Size: 4 Byte, Default Value: 0
SettingDescription
3600 – 2678400 | Available settings: 3600- 2678400 (3600 – 2678400s) |
---|---|
0 | The function is disabled. |
Parameter 174: Electricity report frequency
The interval of sending electricity report to association device (Group
Lifeline).
Size: 4 Byte, Default Value: 0
SettingDescription
3600 – 2678400 | Available settings: 3600- 2678400 (3600 – 2678400s) |
---|---|
0 | The function is disabled. |
Parameter 20: Overload protection
Smart Plug keep detecting the load power, once the AC current exceeds 11.5A
for more than 5s, smart plug’s relay will turn off.
Size: 1 Byte, Default Value: 1
SettingDescription
0 | The function is disabled |
---|---|
1 | The function is enabled. |
Parameter 21: Setting device status after power failure
Define how the Plug reacts after the power supply is back on.
Size: 1 Byte, Default Value: 0
SettingDescription
0 | Smart Plug memorizes its state after a power failure. |
---|---|
1 | Smart Plug does not memorize its state after a power failure. Connected |
device will be on after the power supply is reconnected.
2| Smart Plug does not memorize its state after a power failure. Connected
device will be off after the power supply is reconnected.
Parameter 24: Notification when Load status change
Smart Plug can send notifications to association device (Group Lifeline)
when state of smart plugs load change.
Size: 1 Byte, Default Value: 1
SettingDescription
0 | The function is disabled. |
---|---|
1 | Send Basic report. |
2 | Send Basic report only when Load condition is not changed by Z-WAVE |
Command.
Parameter 254: Enable/disable the configuration command
Lock/unlock all configuration parameters.
Size: 1 Byte, Default Value: 0
SettingDescription
0 | Unlock |
---|---|
1 | Lock |
Parameter 27: Indicator modes
After smart plug being included into a Z-Wave network, the RGB LED indicator
will indicator the situation of load.
Size: 1 Byte, Default Value: 0
SettingDescription
0| The indicator light remains the same as the load on/off status. When the
load is on, the light is on, and the off is off.
---|---
1| Within 5 seconds after the operation load, the indicator light is
consistent with the load on/off status, and then the indicator is off.
Technical Data
Hardware Platform | ZM5202 |
---|---|
Device Type | On/Off Power Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.02 |
Z-Wave Version | 6.81.01 |
Certification ID | ZC10-19016348 |
Z-Wave Product Id | 0x0208.0x0100.0x0019 |
Firmware Updatable | Updatable by Consumer via Internet |
Communications Protocol | Z-Wave Serial API |
Color | White |
Electric Load Type | Dimmable ELV (Magnetic)Dimmable FluorescentDimmable |
LEDDimmable MLV (Magnetic)ELV (Electronic)FluorescentIncandescentInductive
(e.g. Motor)LEDMLV (Magnetic)
Switch Type| Push Button Illuminated
Supported Meter Type| Electric Energy
Security V2| S2_UNAUTHENTICATED
Frequency| XXfrequency
Maximum transmission power| XXantenna
Supported Command Classes
- Association Grp Info
- Association V2
- Basic
- Configuration
- Device Reset Locally
- Firmware Update Md V3
- Manufacturer Specific V2
- Meter V3
- Powerlevel
- Scene Activation
- Scene Actuator Conf
- Security
- Security 2
- Supervision
- Switch Binary
- Transport Service V2
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.