Hank Smart Tech HKSWL-MS08 Motion Sensor User Manual

June 6, 2024
Hank Smart Tech

Hank Smart Tech
HKSWL-MS08 Motion Sensor
User ManualHank Smart Tech HKSWL MS08 Motion
Sensor

PRODUCT OVERVIEW

HKSWL-MS08 is a Wi-Fi-based PIR sensor. You can check the device status, battery level, alarm record, and even receive a push notification via APP when it detects someone or animal moving within the detection range.

PRODUCT FEATURES

  • Digital PIR sensor with low power consumption and strong anti-interference performance;
  • Standard 2.4G wireless Wi-Fi communication technology, two methods for Wi-Fi inclusion, EZ and AP;
  • 2x123A batteries operated or USB powered;
  • Compliant with CE, FCC, and RoHS;
  • Elegant design and flexible installation;
  • Low battery alert and alarm push notification on APP;
  • Immediate report when vibration triggered;

PRODUCT STRUCTURE

Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE 1

Definition of LED Indicator

AP Mode LED indicator blink slow in blue
EZ Mode LED indicator blinks fast in blue

Button Instruction

In the network| Press and hold the Button for 5s then release, resume to default the setting, then it enters into EZ inclusion mode
---|---
Out of the network| Press and hold the Button for 5s then release to switch EZ/AP mode

Note:

  1. In the network: Device has been included in the network.
  2. Out of the network: The device is in the status of the default setting, never configured Wi-Fi.

SPECIFICATIONS

Power supply 6V:2*CR123A or 5V USB
Working current 80mA
Standby current 40uA
Battery Capacity 1300mAh
Detection Distance 8m
Detection Angle 120°
Sensitivity Level 8
Wireless transmitting and receiving frequency 2.4GHz-2.483GHz
network protocol supported IEEE802.11 b/g/n
Encryption type WEP/TKIP/AES,WPS
Transmitting power 802.11 b: +15dBm@ 11Mbps 802.11g: +15dBm@ 54Mbps 802.11n:

+13dBm@ MCS7
working temperature| – 10 – +40°C
Storage temperature| -20 – +60°C
Relative humidity| 8 – 80%RH

INSTALLATION

  1. Power on (battery or USB)
    Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE 2

  2. install the sensor’s holder in the desired location with crews or 3M glue.
    Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE 3

  3. insert the multi-sensor into its holder.
    Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE 4

Download app

Scanning following QR codes to download APP for Android and IOS System. Hank
Smart Tech HKSWL MS08 Motion Sensor - QR CODEhttp://e.tuya.com/smartlife

Registration

Open the APP and type your mobile number or email address, and then confirm the password to complete the registration.

Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE 5

Add Devices

Click“Add Device” or “+” upper right, and then select the “Security &Sensors” and “Sensor(Wi-Fi)” next, input the Wi-Fi password. Click “Next”.
Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE 6

EZ Mode
Power on, the blue indicator flashes one time, then the blue LED indicator will blink fast(if not, press and hold the button for 5S time), enter the EZ mode, click the “Confirm indicator rapidly blink”, and click “Next”, it will Adding device, once it is connected successfully, click “Done” upper right and switch to the device main interface.

Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE 7

AP Mode
Power on, the blue indicator flashes one time , then the blue LED indicator will blink fast and hold the button for 5S time, then the LED indicator will blink slowly in blue, Select “AP Mode” upper right, click “Confirm indicator slowly blink” and “Next”, then click “Go to Connect”. Hank Smart Tech HKSWL
MS08 Motion Sensor - FIGURE 9

Open the smartphone Wi-Fi list, select SmartLife-XXXX, and get back when connected successfully, it will Add the device, Once it is connected successfully, click “Done”  upper right and switch to the device main interface.Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE
10

Device working condition

Motion Detected
When it detects someone or animal moving within the detection range, the device’s main interface would make a difference and push notification. Hank
Smart Tech HKSWL MS08 Motion Sensor - FIGURE 11

Tampered alarm
When it tampers, the device’s main interface would make a difference and push Tampered alarm notification. Hank Smart Tech HKSWL MS08 Motion Sensor -
FIGURE 12

Motion Detected and Tampered alarm
If it is tampered with and detects someone or animal moving within the detection range at the same time, the device’s main interface would make a difference and push Tampered alarm notification. Hank Smart Tech HKSWL MS08
Motion Sensor - FIGURE 13

Delete devices

Click the upper right on the device main interface, click “Remove Device”, select “Disconnect” and then click “Confirm” to remove this device from APP. Select “Disconnect and wipe data” and then click “Confirm” to remove this device from APP and all related data will be wiped. Hank Smart Tech HKSWL
MS08 Motion Sensor - FIGURE 14Hank Smart Tech HKSWL MS08 Motion Sensor - FIGURE
15

FCC NOTICE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference
  2. This device must accept any interference received, including interference that may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals