ARMORLITE Jeep Wrangler JK 4-Door Wheelhouse Covers Instruction Manual
- June 8, 2024
- ARMORLITE
Table of Contents
ARMORLITE Jeep Wrangler JK 4-Door Wheelhouse Covers
OVERVIEW
CAUTION
- READ BEFORE INSTALLING
- DO NOT install Armorlite wheelhouse covers on top of existing factory carpet wheelhouse covers.
- Armorlite wheelhouse cover fit could be compromised if installed over a spray-in liner due to the additional thickness.
- Install Armorlite wheelhouse covers in the proper locations using existing retention points as illustrated in enclosed instructions or visit www.GoArmorlite.com/installation for installation video.
- If the wheelhouse covers are removed for cleaning, follow the installation instructions when reinstalling to ensure proper fit.
- Armorlite products are engineered and designed to fit the vehicle make and model you purchased. DO NOT INSTALL in any other vehicle make or model.
- Warnings label and instructions should be kept with the owner’s manual of your vehicle.
BEFORE YOU BEGIN INSTALLATION
- Wear gloves to protect your hands from any sharp edges in and around the seats.
- Ensure the car is in “Park,” and the emergency brake is applied
For instructions on how to remove factory installed wheelhouse covers there
are third-party online resources available
NO TOOLS REQUIRED
VISIT
www.GoArmorlite.com/installation
FOR A DETAILED INSTRUCTIONAL VIDEO.
Note : Step numbers in the video may not match printed instructions.
WHEELHOUSE COVERS INSTRUCTIONS
- Remove the wheelhouse factory carpet on both the driver and passenger sides
- Wipe down the sheet metal surface to remove dirt and debris. Use water and mild dish soap for stubborn stains.
- Begin by installing the tail section. Tuck the top edge under the sheet meal trim. Tuck the bottom edge under the plastic trim. To assure proper alignment you will need to position yourself in the rear-cargo area by the swing gate. Note: when installing driver side wheelhouse product ensure the wire harness and washer hose are fed between the cut slots
- Position yourself at the rear passenger door. Place the main section over the wheelhouse. Make sure the bottom section properly sits under the seat. Note: Slightly folding down the passenger seat could help with alignment and placement. If the seat is folded down too much it could block the part from properly aligning and nesting the trim edge at the bottom
- Align the hole between the main and tail pieces.
- Use the supplied snap fit connector plug to secure the main piece and tail piece together
- Tuck the main section’s top edge under the sheet meal trim and tuck the bottom edge under the avail- able plastic trim
- Push the cover far enough so the side of the ridge touches the plastic trim. This will prevent the wheelhouse covers from popping
- Repeat the same steps on the opposite side.
- To ensure alignment
- A. If you own an Armorlite cargo mat the wheelhouse covers tuck under the cargo mat. It is designed to nest with it for optimal water management.
- B. If you do not have the Armorlite cargo mat, make sure the finished edge on the Armorlite wheelhouse covers follow the contour of your vehicle’s wheelhouse and lies flat against the cargo floor
LIMITED LIFETIME WARRANTY
Armorlite flooring products are backed by a limited lifetime warranty for materials and workmanship, which means that our products are guaranteed not to break, tear, or deform under normal use. This limited warranty only applies when the product is correctly installed and used in the type of vehicle listed in the product description.
LENGTH OF WARRANTY
The warranty will remain in effect while the original purchaser of the Armorlite product owns the vehicle in which the product is installed. The warranty is not transferrable, which means that the warranty will terminate if you sell or otherwise give the product to someone else.
WHAT THIS WARRANTY DOES NOT COVER
Certain common sense damages to the product are NOT covered by this limited lifetime warranty:
- intentional damage;
- damage resulting from an accident;
- unreasonable use or neglect;
- improper service, installation, or removal;
- damage resulting from product modifications;
- damage to product prior to installation; and
- damage, fading or discoloration from excessive wear and tear and/or excessive exposure
HOW TO MAKE A WARRANTY CLAIM
If you have a valid warranty claim, you must follow the warranty return instructions in the “Warranty Process” section below.
HOW STATE LAW APPLIES
- Armorlite’s express warranties are limited to those expressly stated in this agreement. Armorlite makes no other express representations or warranties, express or implied, regarding the products, including regarding merchantability, suitability, originality, or fitness for a particular purpose, and any such warranties are expressly disclaimed. Any implied warranties, including without limitation the implied warranties of merchantability and fitness for a particular purpose, shall be limited to the duration of this limited warranty.
- In no event will Armorlite be liable, whether in contract or tort (including negligence) for damages in excess of the purchase price of the product, or for any indirect, incidental, special or consequential damages of any kind, or otherwise to the fullest extent these damages may be disclaimed by law. Some jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or a limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from one jurisdiction to another.
WARRANTY PROCESS
Visit our support page and fill out the form to submit a warranty claim. You will be required to upload images to demonstrate proof of a manufacturing defect. Upon receiving your claim an investigation will occur and may take up to 4-8 business days to be completed. If the warranty claim is approved, you will be provided with a replacement product. If your product model has been discontinued, you will be provided with another product of similar composition and price. Armorlite will ship your replacement product at no cost.
SHIPPING
You may be required to return product(s) for a more thorough investigation. A Return Merchandise Authorization Number (RMA#) will be provided at this time. Armorlite will cover return shipping costs and provide you with a pre-paid shipping label. Please write the RMA# on the outside of the box. The product must be cleaned and returned to its original box or equivalent packaging. Packaging must be in good condition. Armorlite is not responsible for lost or damaged packages.
All products must be shipped to: Armorlite, Inc. – Warranty 1506 East Main Street P. O. Box: 669 Old Fort, NC 28762
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>