HILTI 700-AVR Breaker Hammer Corded User Manual
- June 8, 2024
- HILTI
Table of Contents
700-AVR Breaker Hammer Corded
User Manual
700-AVR Breaker Hammer Corded
|
---|---
Original operating instructions
Information about the operating instructions
1.1 About these operating instructions
- Read these operating instructions before the product is used or operated for the first time. This is a prerequisite for safe, trouble-free handling and use of the product.
- Observe the safety instructions and warnings in these operating instructions and on the product.
- Always keep the operating instructions with the product and make sure that the product is accompanied by these operating instructions only, when the product is given to other persons.
1.2 Explanation of symbols
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the
product. The following signal words are used:
DANGER !
▶ Draws attention to imminent danger that will lead to serious personal injury
or fatality.
WARNING !
▶ Draws attention to a potential threat of danger that can lead to serious
injury or fatality.
CAUTION !
▶ Draws attention to a potentially dangerous situation that could lead to
personal injury or damage to the equipment or other property.
1.2.2 Symbols in the operating instructions
The following symbols are used in these operating instructions:
| Comply with the operating instructions
---|---
| Instructions for use and other useful information
| Dealing with recyclable materials
| Do not dispose of electric equipment and batteries as household waste
| Hilti Liion battery
| Hilti charger
1.2.3 Symbols in illustrations
The following symbols are used in illustrations:
2| These numbers refer to the illustrations at the beginning of these
operating instructions.
---|---
3| The numbering reflects the sequence of operations shown in the
illustrations and may deviate from the steps described in the text.
11| Item reference numbers are used in the overview illustration and
refer to the numbers used in the key in the product overview section.
| These characters are intended to specifically draw your attention to certain
points when handling the product.
1.3 Symbols on the product
1.3.1 Symbols on the product
The following symbols are used on the product:
| Chiseling
---|---
| Chisel positioning
|
Protection class II (double-insulated)
****| Wear protective gloves
1.4 Product information
Hilti products are designed for professional use and may be operated, serviced
and maintained only by trained, authorized personnel. This personnel must be
specifically informed about the possible hazards. The product and its
ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use. The type
designation and serial number are printed on the rating plate.
▶ Write down the serial number in the table below. You will be required to
state the product details when contacting Hilti Service or your local Hilti
organization to inquire about the product.
Product information
Breaker | TE 700AVR |
---|---|
Generation | 1 |
Serial no. |
Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
▶ Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
▶ Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may
ignite the dust or fumes.
▶ Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
Electrical safety
▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
▶ Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
▶ Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
▶ Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
▶ When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
▶ If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
▶ Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
▶ Use personal protective equipment. Always wear eye protection. Protective
equipment such as a dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce personal injuries.
▶ Prevent unintentional starting. Ensure the switch is in the offposition
before connecting to power source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
▶ Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
▶ Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair and
clothing away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
▶ If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
▶ Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause
severe injury within a fraction of a second.
Power tool use and care
▶ Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed. ▶ Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
▶ Disconnect the plug from the power source and/or remove the battery pack, if
detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
▶ Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
▶ Maintain power tools and accessories. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
▶ Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
▶ Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
Service
▶ Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
2.2 Hammer safety warnings
▶ Wear ear protectors. Exposure to noise can cause hearing loss.
▶ Use auxiliary handles, if supplied with the tool. Loss of control can cause
personal injury.
▶ Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
2.3 Additional safety instructions for breakers
Personal safety
▶ Use the product and accessories only when they are in perfect working order.
▶ Never tamper with or modify the product or accessories in any way.
▶ When chiseling into ceilings, walls and floors, always make sure that you
have a safe and firm stance. A sudden break-through can affect your balance!
▶ Apply appropriate safety measures at the opposite side of the workpiece in
work that involves breaking through. Parts breaking away could fall out and /
or fall down causing injury to other persons.
▶ You and the other persons in the vicinity must wear suitable eye protection,
a hard hat, ear protection, protective gloves and light respiratory protection
while the product is in use.
▶ Wear protective gloves when changing the accessory tool. Touching the
accessory tool can result in cuts and burns.
▶ Wear eye protection. Flying fragments can injure the body and eyes.
▶ Dust produced by grinding, sanding, cutting and drilling can contain
dangerous chemicals. Some examples are: lead or lead-based paints; brick,
concrete and other masonry products, natural stone and other products
containing silicates; certain types of wood, such as oak, eech and chemically
treated wood; asbestos or materials that contain asbestos. Determine the
exposure of the operator and bystanders by means of the hazard classification
of the materials to be worked. Implement the necessary measures to restrict
exposure to a safe level, for example by the use of a dust collection system
or by the wearing of suitable respiratory protection. The general measures for
reducing exposure include:
▶ working in an area that is well ventilated,
▶ avoidance of prolonged contact with dust,
▶ directing dust away from the face and body,
▶ wearing protective clothing and washing exposed areas of the skin with water
and soap.
▶ Take frequent breaks and do physical exercises to improve the blood
circulation in your fingers. High vibration during long periods of work can
lead to disorders of the blood vessels and nervous system in the fingers,
hands and wrists.
Electrical safety
▶ Before beginning work, check the working area for concealed electric cables
or gas and water pipes. External metal parts of the product could give you an
electric shock or cause an explosion if you accidentally damage an electric
cable or a gas or water pipe.
Power tool use and care
▶ Wait until the product has come to a complete stop before you lay it down.
Description
3.1 Overview of the product 1
1 | Chuck |
---|---|
2 | Function selector switch |
3 | Power level selection switch |
4 | On/off switch |
5 | Grip |
6 | Indicators |
7 | Supply cord |
8 | Air vents |
9 | Knob |
10 | Side handle |
11 | Theft protection indicator (optional) |
12 | Service indicator |
13 | Power level indicator |
3.2 Intended use
The product described is an electrically powered breaker for medium-duty
chiseling work. It is designed for removing and breaking up concrete, masonry
and stone.
▶ Operation is permissible only when connected to a power source providing a
voltage and frequency in compliance with the information given on the type
identification plate.
3.3 Active Vibration Reduction (AVR)
The breaker is equipped with an Active Vibration Reduction (AVR) system, which
reduces vibration significantly.
3.4 Service indicator
The breaker is equipped with a service indicator LED.
Status | Meaning |
---|---|
The service indicator lights red. | End of service interval – servicing is due. |
A fault has occurred in the tool.
The service indicator blinks red.| The overheating prevention cut-out has been
activated.
The voltage provided by the electric supply is too high.
Bring the product to Hilti Service in good time. This will help to ensure that
it’s always ready for use.
3.5 Power level indicator
The breaker is equipped with a power level indicator LED.
Chiseling power can be reduced to approx. 70% by pressing the power level
selector switch. The power level LED then lights up, indicating reduced power.
3.6 Restart interlock
The tool doesn’t restart automatically when the power returns after an
interruption in the supply. The on/off switch must first be released and then
pressed again to restart.
3.7 Items supplied
Breaker, side handle, operating instructions.
You can find other system products approved for your product at your local
Hilti Center or online at: www.hilti.com
Technical data
4.1 Breaker
For details of the rated voltage, frequency, current and input power,
please refer to the power tool’s country-specific type identification plate.
When powered by a generator or transformer, the generator or transformer’s
power output must be at least twice the rated input power shown on the rating
plate of the power tool. The operating voltage of the transformer or generator
must always be within +5% and -15% of the rated voltage of the power tool.
Single impact energy | 1.5 J |
---|---|
Weight | 17.4 lb (7.9 kg) |
Operation
5.1 Preparations at the workplace
CAUTION
Risk of injury! Inadvertent starting of the product.
▶ Unplug the supply cord before making adjustments to the power tool or before
changing accessories.
Observe the safety instructions and warnings in this documentation and on the
product.
5.2 Fitting the side handle 2
CAUTION
Risk of injury! Loss of control over the breaker.
▶ Check that the side handle is fitted correctly and tightened securely.
- Slide the side handle clamping band over the tool holder from the front and into the recess provided.
- Bring the side handle into the desired position.
- Secure the side handle by turning the knob until the clamping band is tight.
5.3 Fitting the accessory tool 3
WARNING
Risk of injury! The accessory tool gets hot during use and may also have sharp
edges.
▶ Wear protective gloves when changing the tool.
DANGER
Risk of fire! Risk of contact between the hot accessory tool and highly
inflammable materials.
▶ Do not lay the hot accessory tool down on highly inflammable materials.
Check the accessory tool for damage or uneven wear each time before use and
replace it if necessary.
Use only the recommended grease supplied by Hilti. Use of unsuitable grease
may cause damage to the product.
- Apply a little grease to the connection end of the accessory tool.
- Push the accessory tool into the chuck as far as it will go, turning it and applying light pressure until it engages with an audible click.
▶ The product is ready for use.
Use only the recommended grease supplied by Hilti. Use of unsuitable grease
may cause damage to the product.
5.4 Removing the accessory tool 4
DANGER
Risk of fire! Risk of contact between the hot accessory tool and highly
inflammable materials.
▶ Do not lay the hot accessory tool down on highly inflammable materials.
WARNING
Risk of injury! The tool becomes hot as a result of use.
▶ Wear protective gloves when changing the tool.
- Pull the chuck back.
- Remove the accessory tool.
Use only the recommended grease supplied by Hilti. Use of unsuitable grease
may cause damage to the product.
5.5 Positioning the chisel 5
The chisel can be adjusted to 24 different positions (in 15° increments).
This ensures that flat chisels and shaped chisels can always be set to the
optimum working position.
▶ Set the function selector switch to and position the chisel as desired.
5.6 Locking the chisel
▶ Set the function selector switch to and rotate the chisel until it engages.
5.7 Setting the chiseling power
Chiseling power can be reduced to approx. 70% by pressing the power level
selector switch. The power level LED then lights up, indicating reduced power.
Chiseling power can be adjusted only when the power tool is switched on and
ready for use. To reselect full chiseling power, press the chiseling power
level selector switch again. Switching off and then on again also causes the
power tool to return to full chiseling power.
▶ Press the power level selector switch.
Types of work
WARNING
Risk of electric shock! Severe injury and burns can result if any attempt is
made to operate the tool without an earth/ground conductor and ground fault
circuit interrupter correctly connected.
▶ Irrespective of whether mains power or generator power is used, always make
sure that an earth/ground conductor and ground fault circuit interrupter are
present in the power supply and that these are correctly connected.
▶ Do not use the product unless these safety measures are in place and fully
operational.
WARNING
A damaged supply cord presents a hazard! Do not touch the supply cord or
extension cord if damaged while working. Disconnect the supply cord plug from
the power outlet.
▶ Check the appliance’s supply cord at regular intervals and have it replaced
by a qualified specialist if found to be damaged.
Full approval must be obtained from the site engineer or architect prior to
beginning the work.
6.1 Chiseling 6
▶ Set the function selector switch to the position.
Care and maintenance
WARNING
Electric shock hazard! Attempting care and maintenance with the supply cord
connected to a power outlet can lead to severe injury and burns.
▶ Always unplug the supply cord before carrying out care and maintenance
tasks.
Care
- Carefully remove stubborn dirt from the tool.
- Clean the air vents carefully with a dry brush.
- Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as they can attack the plastic parts.
Maintenance
WARNING
Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including burns.
▶ Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical specialists.
- Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
- Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired immediately by Hilti Service.
- After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.
To help ensure safe and reliable operation, use only genuine Hilti spare parts
and consumables. Spare parts, consumables and accessories approved by Hilti
for use with the product can be found at your local Hilti Store or online at:
www.hilti.group.
7.1 Cleaning the dust shield
▶ Clean the dust shield on the chuck with a dry, clean cloth at regular
intervals.
▶ Clean the sealing lip by wiping it carefully and then grease it again
lightly with Hilti grease.
▶ It is essential that the dust shield is replaced if the sealing lip is
damaged.
Transport and storage
- Do not transport electric tools with accessory tools fitted.
- Always unplug the supply cord before storing an electric tool or appliance.
- Store tools and appliances in a dry place where they cannot be accessed by children or unauthorized persons.
- Check electric tools or appliances for damage after long periods of transport or storage.
Troubleshooting
If the trouble you are experiencing is not listed in this table or you are
unable to remedy the problem by yourself, please contact Hilti Service.
9.1 Troubleshooting
Trouble or fault | Possible cause | Action to be taken |
---|---|---|
The breaker doesn’t start. | Electronics initialization in progress (takes up | |
to 4 seconds after plugging in). | ▶ Switch the power tool off and then on |
again.
The electronic restart interlock is activated after an interruption in the
electric supply.| ▶ Switch the power tool off and then on again.
Interruption in the elec- tric supply.| ▶ Plug in another electric tool or
appliance and check whether it works.
The generator is in sleep mode.| ▶ Apply a load to the generator by connecting
a second power consumer (e.g. worklight). Switch the tool off and then on
again.
The tool is faulty or ser- vicing is due.| ▶ Have the product repaired only by
Hilti Service.
No hammering ac- tion.| The power tool is too cold.| ▶ Bring the tip of the
accessory tool into contact with the working surface, switch the power tool on
and allow it to run. If necessary, repeat the procedure until the hammering
mechanism begins to operate.
Trouble or fault| Possible cause| Action to be taken
---|---|---
No hammering ac- tion.| Chuck not sufficiently greased.| ▶ Inject 1-2 strokes
of grease from the dispenser into the chuck. Use genuine Hilti grease. Then
fit the accessory tool and distribute the grease in the chuck by pulling the
accessory tool in and out several times.
The service indicator lights red.| The tool is faulty or ser- vicing is due.|
▶ Have the product repaired only by Hilti Service.
The service indicator blinks red.| The overheating preven- tion cut-out has
been activated.| ▶ Allow the tool to cool down.
Clean the air vents. Running under no load is still possible.
The voltage provided by the electric supply is too high.| ▶ Use a different
power outlet. Check the electric supply.
The breaker switches itself off while running.| The overheating prevention
cut-out has been activated.| ▶ Allow the tool to cool down.
Clean the air vents. Running under no load is still possible.
The breaker doesn’t achieve full power.| Power reduction is active.| ▶ Press
the power level selector switch (observe the power level indicator). Unplug
the power tool from the electric supply and then plug it back in.
The extension cord is too long or its gauge is inadequate.| ▶ Use an extension
cord of an approved length and / or of adequate gauge.
The voltage provided by the electric supply is too low.| ▶ Connect the power
tool to a different power source.
Trouble or fault| Possible cause| Action to be taken
---|---|---
The chisel cannot be released from the chuck.| The chuck is not pulled back
fully.| ▶ Pull the tool lock back as far as it will go and remove the insert
tool.
Disposal
Most of the materials from which Hilti tools and appliances are manufactured
can be recycled. The materials must be correctly separated before they can be
recycled. In many ountries, your old tools, machines or appliances can be
returned to Hilti for recycling. Ask Hilti Service or your Hilti
representative for further information.
▶ Do not dispose of power tools, electronic equipment or batteries as
household waste!
Manufacturer’s warranty
▶ Please contact your local Hilti representative if you have questions about the warranty conditions.
https://hilti.to/ontrackapp Hilti Corporation
LI-9494 Schaan
Tel.:+423 234 21 11
Fax:+423 234 29 65
www.hilti.group
Hilti = registered trademark of Hilti Corp., Schaan
Documents / Resources
|
HILTI 700-AVR Breaker Hammer
Corded
[pdf] User Manual
700-AVR Breaker Hammer Corded, 700-AVR, Breaker Hammer Corded, Hammer Corded,
Corded
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>