Hank

Smart Plug

SKU: HKZW-SO03

Quickstart

This is a ****

On/Off Power Switch
for
U.S. / Canada / Mexico.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:

1. Connect the power supply.2) Set the Z-Wave network main controller into inclusion mode (see Z-Wave network controller operating manual).3) Triple click the Z-button or power up the device , RGB LED indicator should blink fast in blue.4) Smart Plug should be recognized and included into the Z-Wave network.

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Smart plug is a Z-Wave Switch plugin module specifically used to enable Z-Wave command and control (on/off) of any plug-in tool. It can report wattage consumption or kWh energy usage. Smart Plug is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade .

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

1. Insert the Plug into a socket,2) Press and hold the Z button for more than 20 seconds,3) If holding time more than 20seconds, the RGB LED indicator will keep yellow for 2 seconds, which means resetting is complete.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

1. Connect the power supply.2) Set the Z-Wave network main controller into inclusion mode (see Z-Wave network controller operating manual).3) Triple click the Z-button or power up the device , RGB LED indicator should blink fast in blue.4) Smart Plug should be recognized and included into the Z-Wave network.

Exclusion

1. Insert the Plug into a socket.2) Set the Z-Wave network controller into the exclusion mode (see Z-Wave controller operating manual).3) Triple click the Z button.4) RGB LED indicator will blink orange till the removing process is completed, than the indicator will keep orange for 3 seconds.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 5| Z-Wave Plus Lifeline.Association command class allows Smart Plug to communicate with other Z-Wave devices directly, such as sending BASIC REPORT whenever the smart plug is turn on or off.
---|---|---

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 151: Threshold of change in wattage

Power threshold to be interpreted, when the change value of load power exceeds the setting threshold, the smart plug will send meter report to associated device (Group Lifeline).
Size: 2 Byte, Default Value: 50

SettingDescription

the associated device

Parameter 152: Threshold of change in wattage percentage

Power percentage threshold to be interpreted, when change value of the load power exceeds the setting threshold, the smart plug will send meter report to associated device (Group Lifeline).
Size: 1 Byte, Default Value: 10

SettingDescription

report to the associated device

Parameter 171: Intervals of sending METER REPORT (for wattage)

The interval of sending meter report(in term of wattage) to associated device (Group Lifeline).
Size: 4 Byte, Default Value: 30

SettingDescription

Parameter 172: Intervals of sending METER REPORT (for kWh)

The interval of sending meter report(in term of kWh) to associated device (Group Lifeline).
Size: 4 Byte, Default Value: 300

SettingDescription

Parameter 173: Intervals of sending METER REPORT (for voltage).

The interval of sending meter report(in term of voltage) to associated device (Group Lifeline).
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 174: Intervals of sending METER REPORT (for current).

The interval of sending meter report(in term of current) to associated device (Group Lifeline).
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 20: Overcurrent protection

Smart Plug keep detecting the load power, once the AC current exceeds 16.5A for more than 5s, smart plug’s relay will turn off.
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 21: Setting Smart Plugs load status after re-power on

Define how the Plug reacts after the power supply is back on.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 24: Notification when Load status change

Smart Plug can send notifications to association device (Group Lifeline) when state of smart plugs load change.
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 27: Indicator modes

After smart plug being included into a Z-Wave network, the RGB LED indicator will indicator the situation of load.
Size: 1 Byte, Default Value: 0

SettingDescription

state of Smart Plugs load changed. RGB LED indicator will turn off if there is no more switch action in 5 seconds.

Technical Data

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>