PHILIPS BT5502 NORELCO Beard Trimmer User Manual
- June 4, 2024
- Philips
Table of Contents
BT5502 NORELCO Beard Trimmer
User Manual
General description (Fig. 1)
- Cutting unit
- Length setting zoom wheel
- On/off button
- Battery charge indicator
- Supply unit
- Small plug
- Cleaning brush
- Beard and stubble guard 1/64 in. 25/64 in. (0.4 mm 10 mm)
- Long hair guard 13/32 in. 25/32 in. (10.4 mm 20 mm)
- Short hair guard 1/64 in. 25/64 in. (0.4 mm 10 mm)
Important safety information
Read this important information carefully before you use the appliance and its
accessories and save it for future reference.
The accessories supplied may vary for different products.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric product, basic precautions should always be followed,
including the following: Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
– Do not reach for a corded product that has fallen into the water. Unplug
immediately from the power outlet.
– Use product only in dry condition. Do not use it while bathing or in a
shower.
– Do not place or store the product where it can fall or be pulled into a tub
or sink. Do not place or drop the product into water or other liquid.
– Except when charging, always unplug this product from the power outlet
immediately after use.
– Remove the power cord from the power outlet and product before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
– Close supervision is required when this product is used by, on, or near
children, or persons with limited physical, sensory, or mental capabilities or
invalids.
– Use this product only for its intended household use as described in this
manual. Do not use attachments not recommended by Philips North America LLC.
– Never operate this product if it has a damaged power cord if it is not
working properly after it has been dropped or damaged, or after the product or
power cord has been dropped into water. For assistance call
1-800-243-3050.
– Keep the power cord away from heated surfaces.
– Never drop or insert any object into any opening.
– Do not use the power cord in or near a power outlet that contains an
electric air freshener to prevent damage to the power cord.
– Do not use products outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
– Always check cutters, cutting units, and guards before using the product. Do
not use the product if cutters, cutting units or guards are damaged, as injury
may occur.
– Always attach the power cord to the product first, then to a power outlet.
To disconnect, set all controls to the `off’ position. Then remove the power
cord from the power outlet.
– Plug the power cord directly into a power outlet. Do not use an extension
cord.
– Unplug the power cord before plugging in or unplugging the product.
– The batteries used in this product may present a fire or chemical burn
hazard if mistreated. Do not disassemble, heat above 100 °C (212 °F) or
incinerate.
IMPORTANT: The power plug contains a transformer. Do not cut off the
power plug to replace it with another plug as this will cause a hazardous
condition.
– Only use original Philips accessories or consumables. Only use detachable
power cord HQ8505.
– Charge, use and store the product at a temperature between 40 °F / 4.5 °C
and 95 °F / 35 °C.
– Keep products and batteries away from fire and do not expose them to direct
sunlight or high temperatures.
– If the product becomes abnormally hot or smelly, changes color, or if
charging takes longer than usual, stop using and charging the product and
contact Philips.
– Do not place products and their batteries in microwave ovens or induction
cookers.
– Do not open, modify, pierce, damage, or dismantle the product or battery to
prevent batteries from heating up or releasing toxic or hazardous substances.
Do not short-circuit, overcharge or reverse charge batteries.
– If batteries are damaged or leaking, avoid contact with the skin or eyes. If
this occurs, immediately rinse well with water and seek medical care.
– When you handle batteries, make sure that your hands, the product, and the
batteries are dry.
– To avoid accidental short-circuiting of batteries after removal, do not let
battery terminals come into contact with metal objects (e.g. coins, hairpins,
rings). Do not wrap batteries in aluminum foil. Tape battery terminals or put
batteries in a plastic bag before you discard them.
SAVE THESE INSTRUCTIONS
Introduction
Congratulations on your purchase and welcome to Philips Norelco!
To fully benefit from the support that Philips Norelco offers, register your
product at www.norelco.com/register.
Charging
Battery status indicator
– When the battery is almost empty, the battery charge indicator flashes
orange.
– When the appliance is charging, the battery charge indicator flashes green.
– When the appliance is fully charged, the battery charge indicator lights up
green continuously.
Note: After approx. 30 minutes, the light goes out automatically.
Charging with the power cord
Charge the product fully before you use it for the first time and after a long
period of disuse. – Charging or using the product at
temperatures below 40°F (4.5°C) or higher than 95°F (35°C) adversely affects
the lifespan of the battery.
– If the product is subjected to a major change in temperature, pressure, or
humidity, let the product acclimatize for 30 minutes before use.
It takes approximately 1 hour to fully charge the product. When it is fully
charged, the product has a cordless operating time of up to 100 minutes.
- Make sure the product is turned off.
- Insert the small plug into the product and put the power plug in any 120 V AC outlet (Fig. 2).
- After charging, remove the power plug from the wall outlet and pull the small plug out of the product.
Note: An adapter plug may be necessary for cord usage in some foreign
countries. Use an attachment plug adapter of the proper configuration for the
power outlet.
Using the product
Always check the product and all accessories before using it. Do not use
the product or any accessory if it is damaged, as this may cause injury.
Always replace a damaged part with one of the original types.
– Use this product for its intended household use as described in this manual.
– For hygienic reasons, the product should only be used by one person.
– Note: This appliance can be used without a cord or when it is connected
to the wall socket (Fig. 3).
Turning the product on and off
– Press the on/off button once to turn the product on or off (Fig. 4).
Beard trimming
Trimming with guard
Note: When you trim for the first time, start at a length setting that is
longer than what you are used to, to familiarize yourself with the product.
Use the trimming guard attached to the cutting element to trim your beard,
stubble, and mustache in your preferred style. This product comes with one
beard and stubble guard.
-
Make sure the product is turned off.
-
Slide the guard into the guiding grooves on both sides of the product (`click’) (Fig. 5).
-
Turn the zoom wheel to select the desired length setting (Fig. 6). The selected length setting is shown on the front of the handle. For the beard and stubble guard: the silver color refers to length settings ranging from 1/64 in. (0.4 mm) to 25/64 in. (10 mm).
-
Turn on the product (Fig. 7).
-
To trim most effectively, move the product against the hair growth direction. Make sure that the surface of the guard always stays in contact with the skin (Fig. 8).
Since all hairs do not grow in the same direction, you may want to try different trimming directions (i.e. upwards, downwards, or across). Practice is best for optimum results. -
If a lot of hair has accumulated in the guard, remove it from the product and blow and/or shake out the hair. Regularly remove cut hair from the guard. The selected length setting does not change when the guard is removed.
-
Turn off and clean the product after each use (see `Cleaning’).
Trimming without guard
If you trim without the guard (Fig. 4), your hair is cut close to the skin
(1/64 in. / 0.4 mm). You can use the trimming head without the guard to:
– Define hair line – Trim nape of the neck
– Remove single unwanted hairs
-
Make sure the product is turned off.
-
Pull the guard off the product (Fig. 9).
-
Never pull at the flexible top of the guard. Always pull at the sides
-
Turn on the product.
-
Make well-controlled movements. Touch the hair lightly with the trimmer.
– For a comfortable trim close to your skin, place the flat side of the trimming head against your skin and make strokes in the desired direction (Fig. 10).
– For contouring, hold the trimming head perpendicular to the skin and move the trimming head upwards or downwards with gentle pressure (Fig. 10). -
Turn off and clean the product after each use (see `Cleaning’).
Hair clipping
– For best results, use the product on clean, dry hair. Do not use it on
freshly washed hair.
– Before you start clipping, comb the hair in the direction of hair growth.
– When you trim for the first time, start at the highest length setting to
familiarize yourself with the product.
– To achieve optimal clipping results, always move the product slowly through
the hair against the direction of hair growth.
-
Make sure the product is turned off.
-
Slide the guard into the guiding grooves on both sides of the product (`click’) (Fig. 5).
-
Turn the zoom wheel to select the desired length setting (Fig. 11). The selected length setting is shown on the front of the product.
– Short hair guard: select a length setting from the silver color, ranging from 1/64 in. (0.4 mm) to 25/64 in.(10 mm).
– Long hair guard: select a length setting from the blue color, ranging from 13/32 in. (10.4 mm) to 25/32 in. (20 mm). -
Turn on the product (Fig. 7).
-
Move the product slowly through the hair, making sure the surface of the guard stays in contact with the skin (Fig. 12).
– Regularly remove cut hairs from the guard. If a lot of hairs have accumulated in the guard, detach the guard from the product and blow and/or shake the hairs out of it. -
Turn off and clean the product after each use (see `Cleaning’).
Tip: Write down the settings you have used to create a certain hairstyle as a reminder for future clipping sessions.
Cleaning
Never use scouring pads, abrasive cleaning agents or aggressive liquids such
as petrol or acetone to clean the appliance.
Clean the product after each use.
-
Turn off the product and disconnect it from the wall outlet.
-
Wipe the housing of the product with a dry cloth.
-
Remove the guard (Fig. 9) and clean it with the cleaning brush and/or rinse it under the tap (Fig. 13).
-
Clean the cutting unit with the cleaning brush and/or rinse it under the tap (Fig. 14).
-
Carefully shake off excess water and let all parts air-dry completely.
Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth. -
After cleaning, reattach the guard (Fig. 5) to the product.
Every 3 months: cleaning trimming head connector
- Turn off the product and disconnect it from the wall outlet.
- Remove the guard (Fig. 9).
- Pull the cutting unit off the product (Fig. 15).
- Clean the trimming head connector and hair chamber with the cleaning brush and/or rinse them under the tap (Fig. 16).
- Clean the inside of the trimming head with the cleaning brush and/or rinse it under the tap (Fig. 17).
- Carefully shake off excess water and let all parts air-dry completely.
- Press the trimming head back on the product. Make sure the projection on the back of the trimming head fits exactly onto the notch in the hair chamber (Fig. 18).
This product has no other user-serviceable parts. For assistance call 1-800-243-3050.
Accessories
Accessories may be purchased at a store near you or on our website www.philips.com/store.
Assistance
For assistance, visit our website:
www.philips.com/support or call toll-free at
1-800-243-3050.
Online information is available 24 hours a day, 7 days a week.
D isposal
– This appliance contains a rechargeable lithium-ion battery which must be
disposed of properly. Contact your local town or city officials for battery
disposal information. You can also call
1-800-822-8837 (Fig. 19) or visit
www.call2recycle.org for battery drop-off
locations.
– For assistance, visit our website
www.philips.com/support or call
1-800-243-3050 toll-free.
– Your product is designed and manufactured with high-quality materials and
components, which can be recycled and reused. For recycling information,
please contact your local waste management facilities or visit
www.recycle.philips.com
Full Five-Year Warranty
Philips North America LLC warrants this new product (except blade and guards)
against defects in materials or workmanship for a period of five years from
the date of purchase, and agrees to repair or replace any defective product
without charge.
IMPORTANT: This warranty does not cover damage resulting from accident,
misuse or abuse, lack of reasonable care, the affixing of any attachment not
provided with the product or loss of parts or subjecting the product to any
but the specified voltage or batteries.
* NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/support for
assistance. It is suggested that for your protection you return shipments of
product by insured mail, insurance prepaid. Damage occurring during shipment
is not covered by this warranty.
NOTE:* No other warranty, written or oral, is authorized by Philips North
America LLC.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above exclusion
and limitations may not apply to you.
Read the enclosed instructions carefully.
45-DAY MONEY-BACK GUARANTEE
If you are not fully satisfied with your product send the product back and
we’ll refund you the full purchase price. The product must be shipped prepaid
by insured mail, insurance prepaid, have the original sales receipt,
indicating purchase price and date of purchase, and the money-back guarantees
return authorization form enclosed. We cannot be responsible for lost mail.
The product must be postmarked no later than 45 days after the date of
purchase. Philips reserves the right to verify the purchase price of the
product and limit refunds not to exceed the suggested retail price.
To obtain the money-back guarantee service, please go
towww.PhilipsMoneyBack.com and follow the
simple 3-step process. Delivery of refund check will occur 68 weeks after
receipt of returned product.**
Manufactured for: Philips Personal Health
a division of Philips North America LLC
P.O. Box 10313, Stamford, CT 06904, USA
This symbol on the product’s nameplate means it is listed by Underwriters’
Laboratories, Inc.
Norelco is a registered trademark of Philips
North America LLC.
PHILIPS and Philips shield are registered trademarks of Koninklijke Philips
N.V.
©2021 Philips North America LLC. All rights reserved.
3000.072.4773.2 (12/21/2021)
****> 75 % recycled paper
References
- Philips - United Kingdom
- Call2Recycle | Leading the Charge For Battery Recycling
- Product registration | Philips
- Philips - United States | Philips
- Philips Customer Service Support - Home | Philips
- Philips Consumer Product Return and Refunds - Cookies Required
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>