TOPDON BTMOBILE lite 12V Wireless Battery and System Tester User Manual
- June 4, 2024
- TOPDON
Table of Contents
TOPDON BTMOBILE lite 12V Wireless Battery and System Tester
Welcome
Thank you for purchasing the TOPDON BT MOBILE lite wireless battery tester.
Please read and understand this manual carefully before using this product. If
any issues arise from the operation of this product, welcome to contact
support@topdon.com for official technical support.
About
BT MOBILE lite is a 12V wireless battery and system tester, adopting the most advanced conductance detection technology and reverse polarity protection technology to provide key information about battery health for technicians, and professionals, so as to identify battery and charging problems quickly, easily and accurately.
Package List
- BT MOBILE lite Wireless Battery Tester
- User Manual
Compatibility
Please be noted that battery type and CCA values (Cold Cranking Amp) marked on the battery label. Please refer to it before using BT MOBILE lite.
- Regular Flooded
- AGM Flat plate
- AGM Spiral
- GEL
- EFB
Note: If your vehicle battery is not the battery mentioned above and you are not sure about which type it is, please choose AGM to conduct test, and the error is within 10%.
Features
Indicator Display
APP Installation & Setup
Installation:
Download and install the App: “BT MOBILE” in Apple Store or Google Play.
*Note: For Apple devices, update to iOS 8.0 or later; for Android
devices, OS 4.3 or later.
Setup:
For the first time, you can choose to register with email or skip login.
Drop-down Menu Function:
Operation Introduction
Before Test:
- Before you test a battery in a vehicle, turn off the ignition, all accessories, and loads. Close all of the vehicle’s doors and trunk lid.
- Make sure the battery terminals are clean. Use a wire brush to clean them, if necessary.
- Connect the RED (+) Positive Battery Clamp to the (+) positive battery terminal, and connect the BLACK (-) Negative Battery Clamp to the (-) negative battery terminal. Ensure that the clamps are securely attached to the correct terminals.
- Open the Bluetooth on the mobile phone.
- Test Introduction
- BATTERY TEST: Display SOH (State of Health), SOC (State of Charge), Voltage, Current, Rating, and the readable analysis results on App;
- CRANKING TEST: Analyze the actual cranking voltage and the cranking time to help you quickly figure out the whole state of the starting system;
- CHARGING TEST: Test different parts of the charging system, including generator, rectifier, rectifier diode, and so on for a reliable charging volt value.
*Note: This tester works best if the battery connectors have been removed and the battery posts have been cleaned. Any corrosion between the tester clamps and the battery connectors, or between the battery connectors and the battery posts, will degrade the tester’s efficiency.
-
Battery Test (for 12V battery)
-
Open the APP on your mobile device and log in.
-
Click the flashing Bluetooth logo in the upper right corner of the home screen, to enter the connection interface, and search for the matching device name. |
-
If the Bluetooth connection is successful, the Bluetooth logo will stop flashing.
-
Click the matching device name to connect.
-
Click “Battery Test” on the home screen and click “Start”
-
Select the battery type and click “OK” to confirm.
-
Select the battery standard marked on the battery label, and click “OK” to confirm. *Note: If the battery is JIS standard, please refer to the table for value and select CCA (SAE) as the test standard (please Google JIS to CCA).
-
Select battery capacity value marked on the battery label and click “OK” to confirm.
-
Click “Next” and wait a few seconds for results.
-
Drop down to share the results.
-
Cranking Test
The engine and all other accessory loads must be OFF during the test. -
Click “Cranking Test” on the home screen, and then click “Start”.
-
Follow the steps and start the vehicle.
-
Click “Test” to get the results.
-
Drop down to share the results.
-
Charging Test
The engine must be ON during the test. -
Click “Charging Test” on the home screen, then click “Start”.
-
Follow the steps and start the vehicle.
-
Step on the accelerator, increase the number of RPM to 2500, keep it for 5 seconds.
-
Click “Next” to get the results.
-
Drop-down to share the results.
-
System Test (Overall Test for Battery)
-
Select “System Test” in the upper right corner, or swipe the home screen left to the system test options.
-
Click “Start” to enter System Test operation interface and complete all tests (refer to Battery Test, Cranking Test, Charging Test for details). Click the right arrow to access to each test result report.
-
Click “System Test” to access to each test result report.
-
Drop down to share test results.
Technical Specification
- Working Temperature: -20°C~65°C (-4°F~140°F)
- Storage Temperature: -20°C~70°C (-4°F~158°F)
- Dimensions: 816827 mm (3.192.681.06 inches)
- Weight: 250 g (8.81 oz)
Warranty
TOPDON Two Years Limited Warranty
The TOPDON Company warrants to its original purchaser that TOPDON products
will be free from defects in material and workmanship for 24 months from the
date of purchase (Warranty Period). For the defects reported during the
Warranty Period, TOPDON will, according to the technical support analysis and
confirmation, either repair or replace the defective part or product.
This limited warranty is void under the following conditions:
Misused, disassembled, altered, or repaired by a non-TOPDON technical repair
specialist. Careless handling and violation of operation.
Notice: All information in this manual is based on the latest information
available at the time of publication and no warranty can be made for its
accuracy or completeness. TOPDON reserves the right to make changes at any
time without notice.
Warnings
- DO NOT place the tester near the engine or exhaust pipe to avoid damage from high temperatures.
- DO NOT smoke, cause sparks, or strike matches near the battery when testing.
- DO NOT remove battery clamps while testing.
- DO NOT put the tester into a highly humid or dusty environment. DO NOT disassemble the tester.
Cautions
- Use this tester in accordance with these instructions, taking into account the working conditions and the work to be performed. Hazardous results could occur if the tool is used for purposes not intended.
- Before testing, make sure the battery terminals are clean. Grease and dust could result in inaccurate test results.
- Wear eye protection when working around batteries.
- Check the insulation layer of the battery clamps is in good condition (no damage, bareness, or disconnection) to avoid electric shock.
- Test in a well-ventilated area. Vehicle exhaust contains toxic carbon monoxide.
- Keep hair, hands, and clothing as well as tester leads and cords away from moving blades and belts.
- Keep the tester out of the reach of children.
FAQ
Q: Is BT MOBILE lite able to test vehicle alternators?
A: It can test the alternator.
Q: Is BT MOBILE lite able to test motorcycle batteries?
A: It can test the 12V battery, between 100 and 2000 CCA. If the motorcycle
battery is within these values, then yes.
Q: How to set the CCA range?
A: You can set the data near the CCA standard number of your battery.
Q: Is BT MOBILE lite able to test 12V deep cycle batteries?
A: Yes.
Q: Will BT MOBILE lite work with marine batteries?
A: Yes, it can work with marine batteries.
Q: What do SOH, SOC, and BAT mean?
A: The SOH refers to the “State of Health”. The SOC is the “State of Charge”
and the BAT is the “Resistance Value” of the battery.
Q: Will this accurately load test ATV batteries?
A: Yes, it can accurately load test ATV batteries.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Support
If you have any questions or doubts, please
Contact us via Hotline:
833-629-4832
Email: support@topdon.com
Website: www.topdon.com
Facebook @TopdonOfficial
Twitter @TopdonOfficial
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>