LG 2208089L Over The Range Microwave Oven Instruction Manual

LG 2208089L Over The Range Microwave Oven

BEFORE YOU BEGIN

(Read these instructions completely and carefully.)

IMPORTANT Save these instructions for local inspector’s use.

IMPORTANT Observe all governing codes and ordinances.

• Note to Installer – Be sure to leave these instructions with the Consumer.
• Note to Consumer – Keep these instructions for future reference.
• Skill level – Installation of this appliance requires basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.

CAUTION : For personal safety, remove house fuse or opencircuit breaker before beginning installation to avoid severe or fatal shock injury

CAUTION : For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 63–85 pound product, plus additional oven loads of up to 50 pounds or a total weight of 113–135 pounds.

CAUTION : For personal safety, this product cannotbe installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.

NOTE : For easier installation and personal safety, it is recommended that two people install this product.

IMPORTANT – PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.

The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance. You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.

Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician. DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

ELECTRICAL REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 13.5 amps and 1.5 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of theNational Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 20 ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.

HOOD EXHAUST

NOTE : Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation

IMPORTANT : If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.

NOTE : For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

NOTE: If you need to install ducts, note that the total duct length of 3¼” x 10” rectangular or 6” diameter round duct should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully.

NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.

Exhaust connection:
The hood exhaust has been designed to mate with a standard 3¼” x 10” rectangular duct. If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6” diameter duct

Maximum duct length:
For satisfactory air movement, the total duct length of 3¼” x 10” rectangular or 6” diameter round duct should not exceed 140 equivalent feet.

Elbows, transitions, wall and roof caps, etc.,
present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts.

IMPORTANT : If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper. Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood

DAMAGE – SHIPMENT/INSTALLATION

• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.

PARTS INCLUDED

HARDWARE PACKET

You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts.

NOTE: Some extra parts are included.

ADDITIONAL PARTS

MOUNTING SPACE

NOTES:

• The space between the cabinets must be 30” wide and free of obstructions.
• If the space between the cabinets is greater than 30”, a Filler Panel Kit may be used to fill in the gap between the microwave oven and the cabinets. Your Owner’s Manual contains the kit number for your model.
• This microwave oven is for installation over ranges up to 36” wide.
• If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation.
• When installing the microwave oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance. MOUNTING SPACE DE68

PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE

1. Remove the installation instructions, Exhaust adaptor, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.
2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
3. Pull the carton up and off the oven.
4. Remove and properly discard plastic bags.
5. Remove the 2 screws from the mounting plate. This plate will be used as the rear wall template and for mounting.

NOTE : You will have to reuse two screws in original location of outcase after removing mounting plate.

FINDING THE WALL STUDS

1. Find the studs, using one of the following methods:
2. A. Stud finder-a magnetic device which locates nails.
3. B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location.
4. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16” or 24” from this mark.
5. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position – beneath flat bottom cabinet

Plate position – beneath recessed bottom cabinet with front overhang

Plate position – beneath framed recessed cabinet bottom

Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level.

THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level. If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level.

1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang.
3. For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D.

ALIGNING THE WALL PLATE

CAUTION : Wear gloves to avoid cutting fingers on sharp edges.

1. Draw a Vertical line on the wall at the center of the 30″ wide space.
2. Draw a Horizontal line on the wall at the bottom of “Rear Wall Template”.
3. Drill 5/8″ holes for toggle bolts on 3 locations (Hole A, Hole B, Hole C) but if the location of hole is same as that of stud, drill a 3/16″ hole for wood screw. In other words, toggle bolt can not be used to the location of stud.

NOTE : DO NOT MOUNT THE PLATE AT THIS TIME.

NOTE : Holes A, B and C are inside area E. If none of A, B and C is in a stud, find a stud somewhere in area E and draw a forth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside

INSTALLATION TYPES

This microwave oven is designed for adaptation to the following three types of ventilation:

1. A. Outside Top Exhaust (Vertical Duct)
2. B. Recirculating (Non-Vented Ductless)
3. C. Outside Back Exhaust (Horizontal Duct)

NOTE : This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). Select the type of ventilation required for your installation and proceed to that section

OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

1. A1. Attach Mounting Plate to Wall
2. A2. Prepare Top Cabinet
3. A3. Mount the Microwave Oven
4. A4. Adjust the Exhaust Adaptor
5. A5. Connecting Ductwork

ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to ¾” onto each bolt
   To use toggle bolts:

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
   NOTE : Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
   CAUTION : Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the TOP CABINET TEMPLATE

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom

INSTALLATION PROCEDURE FOR EXHAUST ADAPTOR AND PROPER DAMPER OPERATION CHECK

• Read the instructions on the TOP CABINET TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION : Wear safety goggles when drilling holes in the cabinet bottom.

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

IMPORTANT : Do not grip or use handle during installation.

NOTE : If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE : We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT : If filler blocks are not used, case damage may occur from over tightening screws.

NOTE : When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift oven by pulling cord.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet

Attach the microwave oven to the top cabinet. Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.

Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

Install grease filter. See the Owner’s Manual packed with the microwave

ADJUST THE EXHAUST ADAPTOR
Open the top cabinet and adjust the exhaust adaptor to connect to the house duct.

CONNECTING DUCTWORK

1. Extend the house duct down to connect to the exhaust adaptor.
2. Seal exhaust duct joints using duct tape.

RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

1. B1. Attach Mounting Plate to Wall
2. B2. Prepare Top Cabinet
3. B3. Adjust Blower
4. B4. Mount Microwave Oven
5. B5. Install Charcoal Filter

ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to ¾” onto each bolt.
   To use toggle bolts:

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
   NOTE : Before tightening toggle bolts and wood screw, make sure to coincide bottom line of the Mounting plate with Horizontal line of “Rear wall Template” and then the Mounting plate is properly centered under the cabinet.
   CAUTION : Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION : Wear safety goggles when drilling holes in the cabinet bottom

ADAPTING MICROWAVE BLOWER FOR RECIRCULATION

NOTE : The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use.

Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.

CAUTION : Do not touch blade of blower forpreventing crack and break. Hold outer case when the blower pull out or back into

Roll the blower unit 90° so that fan blade openings are facing toward the front of the microwave

Place the blower unit back into the opening

CAUTION : Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. Secure blower unit to microwave with the screw

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

IMPORTANT : Do not grip or use handle during installation.

NOTE : If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE : We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT : If filler blocks are not used, case damage may occur from over tightening screws.

NOTE : When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift oven by pulling cord

1. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
2. Attach the microwave oven to the top cabinet.
3. Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.
4. Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
5. Install grease filter. See the Owner’s Manual packed with the microwave.

INSTALLING THE CHARCOAL FILTER

1. Remove screws on top of grille using a #1 Phillips screwdriver.
2. Open the door.
3. Remove the grille
4. After push left, Pull the straight off
5. Install the charocal filter. When properly installed, the wire mesh of the filter should be visible from the front.
6. Reinstall the grille and the screws.
7. Close the door.

OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

1. C1. Prepare Rear Wall
2. C2. Attach Mounting Plate to Wall
3. C3. Prepare Top Cabinet
4. C4. Adjust Blower
5. C5. Mount the Microwave Oven

PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for outside exhaust

• Read the instructions on the REAR WALL TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions of the REAR WALL TEMPLATE

ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to ¾” onto each bolt.

To use toggle bolts:

Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.

NOTE : Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.

CAUTION : Be careful to avoid pinching fingers between the back of the mounting plate and the wall.  Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION : Wear safety goggles when drilling holes in the cabinet bottom.

ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST

1. Remove and save screws that hold the blower plate and the blower motor to the microwave.

2. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.

3. Remove “Parts “A” with tin snips or pliers. (On Some Model)

4. Rotate blower unit counterclockwise 180°.

5. Place the blower unit back into the opening
   CAUTION : Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.
   NOTE : The blower unit exhaust openings should match exhaust openings on rear of microwave oven.

6. Replace the blower plate in the same position as before with the screw.

7. Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven.

Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely.

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE : If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE : We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT : If filler blocks are not used, case damage may occur from over tightening screws.

NOTE : When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift oven by pulling cord.

1. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
2. Attach the microwave oven to the top cabinet.
3. Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
4. Install grease filter. See the Owner’s Manual packed with the microwave.

Before You Use Your Microwave

1. Make sure the microwave oven has been installed according to instructions
2. Remove all packing material from the microwave oven.
3. Install turntable and ring in cavity.
4. Replace house fuse or turn breaker back on.
5. Plug power cord into a dedicated 20 amp electrical outlet.
6. Read the Owner’s Manual.
7. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE.

Code No.:DE68-03587B-02 Printed in Malaysia\

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>